lkml.org 
[lkml]   [2021]   [Sep]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: beaglebone black boot failure Linux v5.15.rc1
From
Date


On 17/09/2021 14:34, Vaittinen, Matti wrote:
> Thanks a lot guys!
>
> On 9/17/21 14:01, Grygorii Strashko wrote:
>>
>>
>> On 17/09/2021 13:57, Grygorii Strashko wrote:
>>>
>>>
>>> On 17/09/2021 13:28, Vaittinen, Matti wrote:
>>>> Hi deeee Ho Tony & All,
>>>>
>>>> On 9/17/21 09:14, Tony Lindgren wrote:
>>>>> Hi,
>>>>>
>>>>> * Vaittinen, Matti <Matti.Vaittinen@fi.rohmeurope.com> [210916 09:15]:
>>>>
>>>>>> My beaglebone black (rev c) based test environment fails to boot with
>>>>>> v5.15-rc1. Boot succeeds with the v5.14.
>>>>>>
>>>>>> Bisecting the Linus' tree pointed out the commit:
>>>>>> [1c7ba565e70365763ea780666a3eee679344b962] ARM: dts: am335x-baltos:
>>>>>> switch to new cpsw switch drv
>>>>>>
>>>>>> I don't see this exact commit touching the BBB device-tree. In Linus'
>>>>>> tree it is a part of a merge commit. Reverting the whole merge on
>>>>>> top of
>>>>>> the v5.15-rc1
>>>>>>
>>>>>> This reverts commit 81b6a285737700c2e04ef0893617b80481b6b4b7,
>>>>>> reversing
>>>>>> changes made to f73979109bc11a0ed26b6deeb403fb5d05676ffc.
>>>>>>
>>>>>> makes my beaglebone black to boot again.
>>>>>>
>>>>>> Yesterday I tried adding this patch:
>>>>>> https://lore.kernel.org/linux-omap/20210915065032.45013-1-tony@atomide.com/T/#u
>>>>>>
>>>>>> pointed by Tom on top of the v5.15-rc1 - no avail. I also did #define
>>>>>> DEBUG at ti-sys.c as was suggested by Tom - but I don't see any
>>>>>> more output.
>>>>>
>>>>> Correction, that was me, not Tom :)
>>>>
>>>> Oh.. Sorry! I don't know where I picked Tom from... My bad!
>>>>
>>>>> For me, adding any kind of delay fixed the issue. Also adding some
>>>>> printk
>>>>> statements fixed it for me.
>>>>>
>>>>>> Any suggestions what to check next?
>>>>>
>>>>> Maybe try the attached patch? If it helps, just try with the with the
>>>>> ti,sysc-delay-us = <2> added as few modules need that after enable.
>>>>>
>>>>> It's also possible there is an issue with some other device that is now
>>>>> getting enabled other than pruss. The last XXX printk output should
>>>>> show
>>>>> the last device being probed.
>>>>>
>>>>> Looks like you need to also enable CONFIG_SERIAL_EARLYCON=y, and pass
>>>>> console=ttyS0,115200 debug earlycon in the kernel command line.
>>>>
>>>> Ah. Thanks again. I indeed lacked the "debug earlycon" parameters. Now
>>>> we're more likely to see what went wrong :) I pasted the serial log form
>>>> failing boot with v5.15-rc1 which has both the patch you linked me above
>>>> and the patch you suggested me to test in previous email.
>>>>
>>>
>
> This really feels like an timing/synchronization issue. Adding various
> prints to
>
> I tried adding prints to omap_reset_deassert() made the Ooops to go
> away. I suspect the prints did change timing just the needed bit. Later
> the boot hanged to NFS mount failing though - but that may also be
> problem on the NFS server side. (I jave a new laptop and I am still
> trying to set-up my development environment there.)
>
>
>>> [...]
>>>
>>>> [    2.786181] ti-sysc 48311fe0.target-module: XXX sysc_probe
>>>> [    2.791994] ti-sysc 48311fe0.target-module:
>>>> 48310000:2000:1fe0:1fe4:NA:00000020:rng
>>>> [    2.800820] omap_rng 48310000.rng: Random Number Generator ver. 20
>>>> [    2.807315] random: crng init done
>>>> [    2.814207] ti-sysc 4a101200.target-module: XXX sysc_probe
>>>> [    2.820080] ti-sysc 4a101200.target-module:
>>>> 4a100000:8000:1200:1208:1204:4edb0100:cpgmac
>>>
>>> This one cpsw
>>>
>>>> [    2.830347] ti-sysc 4a326000.target-module: XXX sysc_probe
>>>
>>> This one pruss and it still shows sysc_probe
>>>
>>> Not sure what are the dependency here :( if any.
>>>
>>> Additional option to try - cmdline param "initcall_debug" and maybe
>>> increase print level in really_probe_debug()
>>>
>>
>> Just to be clear - idea is to see *all* probes - not only sysc.
>>
>> [...]
>>
>
> I added initcall_debug && changed the pr_debug() to pr_err() in
> really_probe_debug(). Log from that run is attached. The
> omap_reset_deassert() was not instrumented to print/delay for this run.

can you try just disable pruss_tm in am335x-bone-common.dtsi?



--
Best regards,
grygorii

\
 
 \ /
  Last update: 2021-09-17 14:38    [W:3.514 / U:0.500 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site