lkml.org 
[lkml]   [2021]   [Aug]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] net/mlx5e: Avoid field-overflowing memcpy()
From
Date
On Fri, 2021-08-06 at 14:50 -0700, Kees Cook wrote:
> In preparation for FORTIFY_SOURCE performing compile-time and run-
> time
> field bounds checking for memcpy(), memmove(), and memset(), avoid
> intentionally writing across neighboring fields.
>
> Use flexible arrays instead of zero-element arrays (which look like
> they
> are always overflowing) and split the cross-field memcpy() into two
> halves
> that can be appropriately bounds-checked by the compiler.
>
> We were doing:
>
>         #define ETH_HLEN  14
>         #define VLAN_HLEN  4
>         ...
>         #define MLX5E_XDP_MIN_INLINE (ETH_HLEN + VLAN_HLEN)
>         ...
>         struct mlx5e_tx_wqe      *wqe  = mlx5_wq_cyc_get_wqe(wq, pi);
>         ...
>         struct mlx5_wqe_eth_seg  *eseg = &wqe->eth;
>         struct mlx5_wqe_data_seg *dseg = wqe->data;
>         ...
>         memcpy(eseg->inline_hdr.start, xdptxd->data,
> MLX5E_XDP_MIN_INLINE);
>
> target is wqe->eth.inline_hdr.start (which the compiler sees as being
> 2 bytes in size), but copying 18, intending to write across start
> (really vlan_tci, 2 bytes). The remaining 16 bytes get written into
> wqe->data[0], covering byte_count (4 bytes), lkey (4 bytes), and addr
> (8 bytes).
>
> struct mlx5e_tx_wqe {
>         struct mlx5_wqe_ctrl_seg   ctrl;                 /*     0   
> 16 */
>         struct mlx5_wqe_eth_seg    eth;                  /*    16   
> 16 */
>         struct mlx5_wqe_data_seg   data[];               /*    32    
> 0 */
>
>         /* size: 32, cachelines: 1, members: 3 */
>         /* last cacheline: 32 bytes */
> };
>
> struct mlx5_wqe_eth_seg {
>         u8                         swp_outer_l4_offset;  /*     0    
> 1 */
>         u8                         swp_outer_l3_offset;  /*     1    
> 1 */
>         u8                         swp_inner_l4_offset;  /*     2    
> 1 */
>         u8                         swp_inner_l3_offset;  /*     3    
> 1 */
>         u8                         cs_flags;             /*     4    
> 1 */
>         u8                         swp_flags;            /*     5    
> 1 */
>         __be16                     mss;                  /*     6    
> 2 */
>         __be32                     flow_table_metadata;  /*     8    
> 4 */
>         union {
>                 struct {
>                         __be16     sz;                   /*    12    
> 2 */
>                         u8         start[2];             /*    14    
> 2 */
>                 } inline_hdr;                            /*    12    
> 4 */
>                 struct {
>                         __be16     type;                 /*    12    
> 2 */
>                         __be16     vlan_tci;             /*    14    
> 2 */
>                 } insert;                                /*    12    
> 4 */
>                 __be32             trailer;              /*    12    
> 4 */
>         };                                               /*    12    
> 4 */
>
>         /* size: 16, cachelines: 1, members: 9 */
>         /* last cacheline: 16 bytes */
> };
>
> struct mlx5_wqe_data_seg {
>         __be32                     byte_count;           /*     0    
> 4 */
>         __be32                     lkey;                 /*     4    
> 4 */
>         __be64                     addr;                 /*     8    
> 8 */
>
>         /* size: 16, cachelines: 1, members: 3 */
>         /* last cacheline: 16 bytes */
> };
>
> So, split the memcpy() so the compiler can reason about the buffer
> sizes.
>
> "pahole" shows no size nor member offset changes to struct
> mlx5e_tx_wqe
> nor struct mlx5e_umr_wqe. "objdump -d" shows no meaningful object
> code changes (i.e. only source line number induced differences and
> optimizations).
>
>

spiting the memcpy doesn't induce any performance degradation ? extra
instruction to copy the 1st 2 bytes ?


[...]
> --- a/drivers/net/ethernet/mellanox/mlx5/core/en/xdp.c
> +++ b/drivers/net/ethernet/mellanox/mlx5/core/en/xdp.c

why only here ? mlx5 has at least 3 other places where we use this
unbound memcpy ..

> @@ -341,8 +341,10 @@ mlx5e_xmit_xdp_frame(struct mlx5e_xdpsq *sq,
> struct mlx5e_xmit_data *xdptxd,
>  
>         /* copy the inline part if required */
>         if (sq->min_inline_mode != MLX5_INLINE_MODE_NONE) {
> -               memcpy(eseg->inline_hdr.start, xdptxd->data,
> MLX5E_XDP_MIN_INLINE);
> +               memcpy(eseg->inline_hdr.start, xdptxd->data,
> sizeof(eseg->inline_hdr.start));
>                 eseg->inline_hdr.sz =
> cpu_to_be16(MLX5E_XDP_MIN_INLINE);
> +               memcpy(dseg, xdptxd->data + sizeof(eseg-
> >inline_hdr.start),
> +                      MLX5E_XDP_MIN_INLINE - sizeof(eseg-
> >inline_hdr.start));
>                 dma_len  -= MLX5E_XDP_MIN_INLINE;
>                 dma_addr += MLX5E_XDP_MIN_INLINE;
>                 dseg++;


\
 
 \ /
  Last update: 2021-08-07 00:18    [W:1.378 / U:0.056 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site