lkml.org 
[lkml]   [2021]   [Jul]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
SubjectRe: [RFC PATCH 2/3] mwifiex: pcie: add reset_d3cold quirk for Surface gen4+ devices
From
Date
On 5/24/21 10:27 PM, Amey Narkhede wrote:
> On 21/05/23 12:28PM, Jonas Dreßler wrote:
>> On 5/22/21 8:44 PM, Amey Narkhede wrote:
>>> On 21/05/22 03:18PM, Jonas Dreßler wrote:
>>>> From: Tsuchiya Yuto <kitakar@gmail.com>
>>>>
>>>> To reset mwifiex on Surface gen4+ (Pro 4 or later gen) devices, it
>>>> seems that putting the wifi device into D3cold is required according
>>>> to errata.inf file on Windows installation (Windows/INF/errata.inf).
>>>>
>>>> This patch adds a function that performs power-cycle (put into D3cold
>>>> then D0) and call the function at the end of reset_prepare().
>>>>
>>>> Note: Need to also reset the parent device (bridge) of wifi on SB1;
>>>> it might be because the bridge of wifi always reports it's in D3hot.
>>>> When I tried to reset only the wifi device (not touching parent),
it gave
>>>> the following error and the reset failed:
>>>>
>>>> acpi device:4b: Cannot transition to power state D0 for
parent in D3hot
>>>> mwifiex_pcie 0000:03:00.0: can't change power state from
D3cold to D0 (config space inaccessible)
>>>>
>>> May I know how did you reset only the wifi device when you encountered
>>> this error?
>>
>> Not exactly sure what you mean by that, the trick was to put the parent
>> bridge into D3cold and then into D0 before transitioning the card into
>> D0.
>>
> If the parent bridge has multiple devices attached to it, this can
> have some side effects on other devices after the reset but as you
> mentioned below that parent bridge is only connected to wifi card it
> should be fine in that case.
>
>> That "Cannot transition to power state" warning is just the kernel
>> enforcing ACPI specs afaik, and that prevents us from putting the device
>> into ACPI state D0. This in turn means the device still has no power and
>> we can't set the PCI power state to D0, which is the second error.
>>
>>>
>>>> Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
>>>> Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
>>>> ---
>>>> drivers/net/wireless/marvell/mwifiex/pcie.c | 7 +
>>>> .../wireless/marvell/mwifiex/pcie_quirks.c | 123
++++++++++++++++++
>>>> .../wireless/marvell/mwifiex/pcie_quirks.h | 3 +
>>>> 3 files changed, 133 insertions(+)
>>>>
>>>> diff --git a/drivers/net/wireless/marvell/mwifiex/pcie.c
b/drivers/net/wireless/marvell/mwifiex/pcie.c
>>>> index 02fdce926de5..d9acfea395ad 100644
>>>> --- a/drivers/net/wireless/marvell/mwifiex/pcie.c
>>>> +++ b/drivers/net/wireless/marvell/mwifiex/pcie.c
>>>> @@ -528,6 +528,13 @@ static void mwifiex_pcie_reset_prepare(struct
pci_dev *pdev)
>>>> mwifiex_shutdown_sw(adapter);
>>>> clear_bit(MWIFIEX_IFACE_WORK_DEVICE_DUMP, &card->work_flags);
>>>> clear_bit(MWIFIEX_IFACE_WORK_CARD_RESET, &card->work_flags);
>>>> +
>>>> + /* For Surface gen4+ devices, we need to put wifi into D3cold right
>>>> + * before performing FLR
>>>> + */
>>>> + if (card->quirks & QUIRK_FW_RST_D3COLD)
>>>> + mwifiex_pcie_reset_d3cold_quirk(pdev);
>>>> +
>>>> mwifiex_dbg(adapter, INFO, "%s, successful\n", __func__);

>>>> card->pci_reset_ongoing = true;
>>>> diff --git a/drivers/net/wireless/marvell/mwifiex/pcie_quirks.c
b/drivers/net/wireless/marvell/mwifiex/pcie_quirks.c
>>>> index 4064f99b36ba..b5f214fc1212 100644
>>>> --- a/drivers/net/wireless/marvell/mwifiex/pcie_quirks.c
>>>> +++ b/drivers/net/wireless/marvell/mwifiex/pcie_quirks.c
>>>> @@ -15,6 +15,72 @@
>>>>
>>>> /* quirk table based on DMI matching */
>>>> static const struct dmi_system_id mwifiex_quirk_table[] = {
>>>> + {
>>>> + .ident = "Surface Pro 4",
>>>> + .matches = {
>>>> + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
>>>> + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Pro 4"),
>>>> + },
>>>> + .driver_data = (void *)QUIRK_FW_RST_D3COLD,
>>>> + },
>>>> + {
>>>> + .ident = "Surface Pro 5",
>>>> + .matches = {
>>>> + /* match for SKU here due to generic product name "Surface Pro" */
>>>> + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
>>>> + DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "Surface_Pro_1796"),
>>>> + },
>>>> + .driver_data = (void *)QUIRK_FW_RST_D3COLD,
>>>> + },
>>>> + {
>>>> + .ident = "Surface Pro 5 (LTE)",
>>>> + .matches = {
>>>> + /* match for SKU here due to generic product name "Surface Pro" */
>>>> + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
>>>> + DMI_EXACT_MATCH(DMI_PRODUCT_SKU, "Surface_Pro_1807"),
>>>> + },
>>>> + .driver_data = (void *)QUIRK_FW_RST_D3COLD,
>>>> + },
>>>> + {
>>>> + .ident = "Surface Pro 6",
>>>> + .matches = {
>>>> + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
>>>> + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Pro 6"),
>>>> + },
>>>> + .driver_data = (void *)QUIRK_FW_RST_D3COLD,
>>>> + },
>>>> + {
>>>> + .ident = "Surface Book 1",
>>>> + .matches = {
>>>> + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
>>>> + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Book"),
>>>> + },
>>>> + .driver_data = (void *)QUIRK_FW_RST_D3COLD,
>>>> + },
>>>> + {
>>>> + .ident = "Surface Book 2",
>>>> + .matches = {
>>>> + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
>>>> + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Book 2"),
>>>> + },
>>>> + .driver_data = (void *)QUIRK_FW_RST_D3COLD,
>>>> + },
>>>> + {
>>>> + .ident = "Surface Laptop 1",
>>>> + .matches = {
>>>> + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
>>>> + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Laptop"),
>>>> + },
>>>> + .driver_data = (void *)QUIRK_FW_RST_D3COLD,
>>>> + },
>>>> + {
>>>> + .ident = "Surface Laptop 2",
>>>> + .matches = {
>>>> + DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Microsoft Corporation"),
>>>> + DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "Surface Laptop 2"),
>>>> + },
>>>> + .driver_data = (void *)QUIRK_FW_RST_D3COLD,
>>>> + },
>>>> {}
>>>> };
>>>>
>>>> @@ -29,4 +95,61 @@ void mwifiex_initialize_quirks(struct
pcie_service_card *card)
>>>>
>>>> if (!card->quirks)
>>>> dev_info(&pdev->dev, "no quirks enabled\n");
>>>> + if (card->quirks & QUIRK_FW_RST_D3COLD)
>>>> + dev_info(&pdev->dev, "quirk reset_d3cold enabled\n");
>>>> +}
>>>> +
>>>> +static void mwifiex_pcie_set_power_d3cold(struct pci_dev *pdev)
>>>> +{
>>>> + dev_info(&pdev->dev, "putting into D3cold...\n");
>>>> +
>>>> + pci_save_state(pdev);
>>>> + if (pci_is_enabled(pdev))
>>>> + pci_disable_device(pdev);
>>>> + pci_set_power_state(pdev, PCI_D3cold);
>>>> +}
>>> pci_set_power_state with PCI_D3cold state calls
>>> pci_bus_set_current_state(dev->subordinate, PCI_D3cold).
>>> Maybe this was the reason for the earlier problem you had?
>>> Not 100% sure about this though CCing: Alex
>>
>> Hmm, so we'd only have to put the bridge into D3cold and that takes care
>> of the device going to D3cold automatically?
>>
> Yeah I think it should do it. Have you tried this?

Finally found some time to try that now and looks like it doesn't work.
First reset works fine, but on the second one the device can't switch
from D3cold to D0:

mwifiex_pcie 0000:01:00.0: can't change power state from D3cold to D0
(config space inaccessible)
Thanks,
Jonas

>>>
>>>> +
>>>> +static int mwifiex_pcie_set_power_d0(struct pci_dev *pdev)
>>>> +{
>>>> + int ret;
>>>> +
>>>> + dev_info(&pdev->dev, "putting into D0...\n");
>>>> +
>>>> + pci_set_power_state(pdev, PCI_D0);
>>>> + ret = pci_enable_device(pdev);
>>>> + if (ret) {
>>>> + dev_err(&pdev->dev, "pci_enable_device failed\n");
>>>> + return ret;
>>>> + }
>>>> + pci_restore_state(pdev);
>>> On the side note just save and restore is enough in this case?
>>> What would be the device <-> driver state after the reset as you
>>> are calling this on parent_pdev below so that affects other
>>> devices on bus?
>>
>> Not sure we can do anything more than save and restore, can we? I don't
>> think it will affect other devices on the bus, the parent bridge is only
>> connected to the wifi card, nothing else.
>>
> I was thinking of doing remove-reset-rescan but I think save-restore
> should be ok if there is a single device connected to the parent bridge.
>
> Thanks,
> Amey
> [...]
>>>> diff --git a/drivers/net/wireless/marvell/mwifiex/pcie_quirks.h
b/drivers/net/wireless/marvell/mwifiex/pcie_quirks.h
>>>> index 7a1fe3b3a61a..549093067813 100644
>>>> --- a/drivers/net/wireless/marvell/mwifiex/pcie_quirks.h
>>>> +++ b/drivers/net/wireless/marvell/mwifiex/pcie_quirks.h
>>>> @@ -5,4 +5,7 @@
>>>>
>>>> #include "pcie.h"
>>>>
>>>> +#define QUIRK_FW_RST_D3COLD BIT(0)
>>>> +
>>>> void mwifiex_initialize_quirks(struct pcie_service_card *card);
>>>> +int mwifiex_pcie_reset_d3cold_quirk(struct pci_dev *pdev);
>>>> --
>>>> 2.31.1
>>>>
>>
>> Thanks for the review,
>> Jonas

\
 
 \ /
  Last update: 2021-07-09 16:11    [W:0.117 / U:0.516 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site