lkml.org 
[lkml]   [2021]   [Jul]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v7 4/5] arm64: dts: add support for Marvell cn9130-crb platform
Date
From: Konstantin Porotchkin <kostap@marvell.com>

The Marvell reference platform CN9130-CRB is a small form factor
board in a metal case. The platform is based on CN9130 SoC with
addition of 8 Gigabit ports SOHO Ethernet switch.
The reference platform features the following:
* Up to 4 CPU cores ARMv8 Cortex-A72 CPU
* CPU core operating speed of up to 2.2GHz
* DDR4 DIMM – 8GB 64bit+ECC @ 2400Mhz.
* 1x eMMC 8GB device
* 1x uSD card 4 bits port on CP
* 1x 128MB SPI NOR flash memory
* 1x USB 3.0 Host port (Type A)
* 1x SATA Gen3 via M.2
* 1x USB 3.0 via M.2
* 1x SIM card slot
* 1x 1G Ethernet port via RGMII
* 1x 10G switch port over SFP+ connector
* 8x 1G ports through 88E6393X switch via XFI
* 1x 2.5G/1G/100M/10M port via HS_SGMII
* 1x PCI Express (PCIe)x1 Gen 3.0
* 1x PCI Express (PCIe)x4 Gen 3.0 via NVMe M.2
* JTAG port

The CRB board uses MCP23017 i2c pin controller that drives the
onboard eMMC abd USB 3,0 port power lines.
The following configuration should be enabled for this controller
support:
CONFIG_PINCTRL_MCP23S08=y

The plaform supports two HW configurations - "A" and "B"
CN9130-CRB-A
* AP-MPP configuration: SDIO, UART
* CP0 Serdes configuration:
* Lane0-3: NVMe (PCIe x4)
* Lane4: XFI
* Lane5: HS_SGMII

2. CN9130-CRB-B
* AP-MPP configuration: SDIO, UART
* CP0-MPP configuration: RGMII, SDIO, I2C0, I2C1, SMI, XSMI
* CP0 Serdes configuration:
* Lane0: PCIe x1
* Lane1: USB3_0 x1
* Lane2: SATA x1
* Lane3: USB3_1 x1
* Lane4: XFI
* Lane5: HS_SGMII

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
---
arch/arm64/boot/dts/marvell/Makefile | 2 +
arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++++
arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++++
arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 222 ++++++++++++++++++++
4 files changed, 308 insertions(+)
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi

diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 5e39f9774e68..c686a8dd3ca5 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -21,3 +21,5 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9131-db-B.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts b/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
new file mode 100644
index 000000000000..a7b6dfba8af5
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include "cn9130-crb.dtsi"
+
+/ {
+ model = "Marvell Armada CN9130-CRB-A";
+};
+
+&cp0_pcie0 {
+ status = "okay";
+ num-lanes = <4>;
+ num-viewport = <8>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy0 0
+ &cp0_comphy1 0
+ &cp0_comphy2 0
+ &cp0_comphy3 0>;
+ iommu-map =
+ <0x0 &smmu 0x480 0x20>,
+ <0x100 &smmu 0x4a0 0x20>,
+ <0x200 &smmu 0x4c0 0x20>;
+ iommu-map-mask = <0x031f>;
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy0>;
+ phy-names = "usb";
+};
+
+&cp0_usb3_1 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy1>;
+ phy-names = "usb";
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts b/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
new file mode 100644
index 000000000000..0904cb0309ae
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include "cn9130-crb.dtsi"
+
+/ {
+ model = "Marvell Armada CN9130-CRB-B";
+};
+
+&cp0_pcie0 {
+ status = "okay";
+ num-lanes = <1>;
+ num-viewport = <8>;
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy0 0>;
+ iommu-map =
+ <0x0 &smmu 0x480 0x20>,
+ <0x100 &smmu 0x4a0 0x20>,
+ <0x200 &smmu 0x4c0 0x20>;
+ iommu-map-mask = <0x031f>;
+};
+
+&cp0_sata0 {
+ status = "okay";
+ sata-port@0 {
+ status = "okay";
+ /* Generic PHY, providing serdes lanes */
+ phys = <&cp0_comphy2 0>;
+ };
+};
+
+&cp0_usb3_0 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy0>;
+ phy-names = "usb";
+ phys = <&cp0_comphy1 0>;
+};
+
+&cp0_usb3_1 {
+ status = "okay";
+ usb-phy = <&cp0_usb3_0_phy1>;
+ phy-names = "usb";
+ phys = <&cp0_comphy3 1>;
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
new file mode 100644
index 000000000000..75933477324a
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#include "cn9130.dtsi" /* include SoC device tree */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ aliases {
+ i2c0 = &cp0_i2c0;
+ ethernet0 = &cp0_eth0;
+ ethernet1 = &cp0_eth1;
+ ethernet2 = &cp0_eth2;
+ };
+
+ memory@00000000 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>;
+ };
+
+ ap0_reg_mmc_vccq: ap0_mmc_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "ap0_mmc_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&expander0 5 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+
+ cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0-xhci1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ cp0_usb3_0_phy0: cp0_usb3_phy0 {
+ compatible = "usb-nop-xceiv";
+ };
+
+ cp0_usb3_0_phy1: cp0_usb3_phy1 {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <&cp0_reg_usb3_vbus1>;
+ };
+
+ cp0_reg_sd_vccq: cp0_sd_vccq@0 {
+ compatible = "regulator-gpio";
+ regulator-name = "cp0_sd_vccq";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&cp0_gpio2 18 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x1
+ 3300000 0x0>;
+ };
+
+ cp0_reg_sd_vcc: cp0_sd_vcc@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "cp0_sd_vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+/* on-board eMMC U6 */
+&ap_sdhci0 {
+ pinctrl-names = "default";
+ bus-width = <8>;
+ status = "okay";
+ mmc-ddr-1_8v;
+ vqmmc-supply = <&ap0_reg_mmc_vccq>;
+};
+
+&cp0_syscon0 {
+ cp0_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+
+ cp0_i2c0_pins: cp0-i2c-pins-0 {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "i2c0";
+ };
+ cp0_i2c1_pins: cp0-i2c-pins-1 {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+ cp0_sdhci_cd_pins_crb: cp0-sdhci-cd-pins-crb {
+ marvell,pins = "mpp55";
+ marvell,function = "gpio";
+ };
+ cp0_sdhci_pins: cp0-sdhi-pins-0 {
+ marvell,pins = "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+ cp0_spi0_pins: cp0-spi-pins-0 {
+ marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
+ marvell,function = "spi1";
+ };
+ };
+};
+
+&cp0_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+ expander0: mcp23x17@20 {
+ compatible = "microchip,mcp23017";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+ status = "okay";
+ };
+};
+
+&cp0_i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_i2c1_pins>;
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+
+&cp0_sdhci0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_sdhci_pins
+ &cp0_sdhci_cd_pins_crb>;
+ bus-width = <4>;
+ cd-gpios = <&cp0_gpio2 23 GPIO_ACTIVE_HIGH>;
+ vqmmc-supply = <&cp0_reg_sd_vccq>;
+ vmmc-supply = <&cp0_reg_sd_vcc>;
+ status = "okay";
+};
+
+&cp0_spi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_spi0_pins>;
+ reg = <0x700680 0x50>, /* control */
+ <0x2000000 0x1000000>; /* CS0 */
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <0x1>;
+ #size-cells = <0x1>;
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ /* On-board MUX does not allow higher frequencies */
+ spi-max-frequency = <40000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "U-Boot";
+ reg = <0x0 0x200000>;
+ };
+
+ partition@400000 {
+ label = "Filesystem";
+ reg = <0x200000 0xe00000>;
+ };
+ };
+ };
+};
+
+&cp0_mdio {
+ status = "okay";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+};
+
+&cp0_xmdio {
+ status = "okay";
+ nbaset_phy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ reg = <0>;
+ };
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+&cp0_eth0 {
+ /* This port is connected to 88E6393X switch */
+ status = "okay";
+ phy-mode = "10gbase-kr";
+ managed = "in-band-status";
+ phys = <&cp0_comphy4 0>;
+};
+
+&cp0_eth1 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
+
+&cp0_eth2 {
+ /* This port uses "2500base-t" phy-mode */
+ status = "disabled";
+ phy = <&nbaset_phy0>;
+ phys = <&cp0_comphy5 2>;
+};
+
--
2.17.1
\
 
 \ /
  Last update: 2021-07-08 14:47    [W:0.073 / U:1.160 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site