lkml.org 
[lkml]   [2021]   [Jul]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 01/11] media: ov5640: Use runtime PM to control sensor power
Hi Laurent,

On Thu, Jul 08, 2021 at 12:51:16AM +0300, Laurent Pinchart wrote:
> Hi Sakari,
>
> On Thu, Jul 08, 2021 at 12:44:15AM +0300, Sakari Ailus wrote:
> > On Thu, Jul 08, 2021 at 12:00:57AM +0300, Laurent Pinchart wrote:
> > > On Wed, Jul 07, 2021 at 11:37:18PM +0300, Sakari Ailus wrote:
> > > > On Fri, Jun 25, 2021 at 12:51:50AM +0530, Pratyush Yadav wrote:
> > > > > Calling s_power subdev callback is discouraged. Instead, the subdevs
> > > > > should use runtime PM to control its power. Use runtime PM callbacks to
> > > > > control sensor power. The pm counter is incremented when the stream is
> > > > > started and decremented when the stream is stopped.
> > > > >
> > > > > Refactor s_stream() a bit to make this new control flow easier. Add a
> > > > > helper to choose whether mipi or dvp set_stream needs to be called. The
> > > > > logic flow is also changed to make it a bit clearer.
> > > > >
> > > > > Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
> > > > >
> > > > > ---
> > > > >
> > > > > Changes in v3:
> > > > > - Clean up the logic in ov5640_s_stream() a bit.
> > > > > - Use pm_runtime_resume_and_get() instead of pm_runtime_get_sync().
> > > > > - Rename the label error_pm to disable_pm.
> > > > >
> > > > > Changes in v2:
> > > > > - New in v2.
> > > > >
> > > > > drivers/media/i2c/Kconfig | 2 +-
> > > > > drivers/media/i2c/ov5640.c | 127 +++++++++++++++++++++++--------------
> > > > > 2 files changed, 79 insertions(+), 50 deletions(-)
> > > > >
> > > > > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> > > > > index 588f8eb95984..8f43a4d7bcc1 100644
> > > > > --- a/drivers/media/i2c/Kconfig
> > > > > +++ b/drivers/media/i2c/Kconfig
> > > > > @@ -929,7 +929,7 @@ config VIDEO_OV2740
> > > > >
> > > > > config VIDEO_OV5640
> > > > > tristate "OmniVision OV5640 sensor support"
> > > > > - depends on OF
> > > > > + depends on OF && PM
> > > >
> > > > Could you add support for runtime PM without requiring CONFIG_PM?
> > > >
> > > > Essentially you'll need to power on the device in probe and power it off in
> > > > probe, and make sure the runtime PM nop variant functions return the value
> > > > you'd expect.
> > >
> > > I've gone through that in several sensor drivers, and it really
> > > increases the complexity to get it right, to a point where I'm not
> > > comfortable asking someone to do the same (not to mention the very, very
> >
> > I don't think it's very complicated, really. Looking at examples of other
> > drivers (e.g. imx334) doing exactly the same helps as you don't need to
> > check for individual functions.
> >
> > The complexity of the power management in this driver is mostly because of
> > evolutionary development done over time, it's an old driver.
>
> https://git.linuxtv.org/pinchartl/media.git/commit/?h=sensors/ar0330/driver&id=e72ca23c4c6b1ab6b06ac48280726e09d63cc818
>
> Look at the changes to ar0330_probe(). As far as I understand, anything
> less than that would be incorrect, and it's way too easy to get it
> wrong.

The driver uses autosuspend that requires quite a few extra calls to
runtime PM framework. The only other driver doing this may be the CCS
driver.

>
> > > high chance that it won't be done correctly). What's the practical
> > > drawback in requiring CONFIG_PM ?
> >
> > Good question. CONFIG_PM is something you can disable (for a reason I can't
> > think of though). Why should a driver depend on it when it could perfectly
> > work without it as well?
>
> Because it requires additional complexity in the driver, times the
> number of sensor drivers we have in the kernel. Not even mentioning test

How much of additional complexity?

You need to call the function powering on the sensor in probe, and call
another one to power the sensor off in remove, and make sure the use of
runtime PM functions is correct. Good examples exist of this.

Even if you fully relied on runtime PM and do not call the aforementioned
functions directly, you need to power on the sensor in probe using runtime
PM on DT based systems which is not the case on ACPI based systems. These
differences need to be taken into account in that case.

> coverage, I'm pretty sure very few people would test the sensor drivers
> without CONFIG_PM.

That is probably true.

--
Regards,

Sakari Ailus

\
 
 \ /
  Last update: 2021-07-08 12:29    [W:0.092 / U:1.156 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site