lkml.org 
[lkml]   [2021]   [Jul]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 2/3] hwmon: da9063: HWMON driver
On Wed, Jul 07, 2021 at 12:20:45AM +0000, Vincent Pelletier wrote:
> Hello,
>
> Thanks a lot for your reviews.
>
> On Tue, 6 Jul 2021 10:42:01 -0700, Guenter Roeck <linux@roeck-us.net> wrote:
> > -EINVAL seems wrong. Maybe -EIO or -ETIMEDOUT.
>
> On this topic, I've been hesitating to change this code to the
> following. Would it be acceptable ?
>
> ret = wait_for_completion_timeout(...)
> if (ret == 0)
> warn[_once](...)
> ...
> if (adc_man & DA9063_ADC_MAN) {
> ret = -ETIMEDOUT;
> goto err_mread;
> }
>
> The warn is to make it easier to debug in case of IRQ issue. The reason

"to debug". Then make it a debug message.

> I'm caring is that I happen to have triggered such issue while testing
> this driver, as the GPIO and PLIC on the hifive-unmatched seem to
> disagree with each other. I debugged this and reported to linux-riscv,
> and I believe the issue is not in da9063-hwmon: it also affects
> da9063-onkey, and my GPIO-level workaround fixes both.
>
> On a tangential topic: this chip is supposed to complete an ADC cycle
> in 10ms, so 1s timeout seems a lot to me. On the one hand it made the
> IRQ issue obvious, but on the other hand a safety factor of 100 seems
> enormous to me. What would be a usual/reasonable safety factor ? 10 ?
> 2 ?

Your call, really.

Guenter

>
> > > + ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
> > > + da9063_hwmon_irq_handler,
> > > + IRQF_TRIGGER_LOW | IRQF_ONESHOT,
> >
> > Is that correct ? The trigger condition is normally provided by
> > devicetree.
>
> At least it is consistent with the existing and related da9063-onkey:
>
> irq = platform_get_irq_byname(pdev, "ONKEY");
> if (irq < 0)
> return irq;
>
> error = devm_request_threaded_irq(&pdev->dev, irq,
> NULL, da9063_onkey_irq_handler,
> IRQF_TRIGGER_LOW | IRQF_ONESHOT,
> "ONKEY", onkey);
>
> I am not familiar enough with IRQ handling to tell if IRQF_TRIGGER_LOW
> has an actual meaning here: in my understanding the regmap handler
> decides how to clear an interrupt based on regmap_irq_chip content, and
> this is coming from mfd/da9063-irq.c .
>
> Are both devm_request_threaded_irq() equally wrong ?
>
No idea. My understanding is that devicetree data is used unless
an explicit method is specified. That is why I was asking _if_ this
is correct, and did not claim that it is wrong.

> > > + /* set trim temperature offset to value read at startup */
> > > + hwmon->tjunc_offset = (signed char)hwmon->da9063->t_offset;
> >
> > Can you explain why this is read in and passed from the mfd driver
> > and not here ?
>
> I cannot, at least not with something other than "this is how I found
> the code", which I realise is not satisfactory.
> I've been holding back on changes as I felt constrained by preserving
> the original author's name on the changes (both Author and
> Signed-off-by), but this split was indeed bothering me.
>
Sorry, that is not a good argument. On the contrary, if I have to assume
that the code has non-technical constraints, I am inclined to just reject
it for that very reason.

Guenter

\
 
 \ /
  Last update: 2021-07-07 02:59    [W:0.051 / U:0.168 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site