lkml.org 
[lkml]   [2021]   [Jul]   [29]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[RFC-PATCH] net: stmmac: Add KR port support.
Date
From: Balamurugan Selvarajan <balamsel@cisco.com>

For KR port the mii interface is a chip-to-chip
interface without a mechanical connector. So PHY
inits are not applicable. In this case MAC is
configured to operate at forced speed(1000Mbps)
and full duplex. Modified driver to accommodate
PHY and NON-PHY mode.

Cc: xe-linux-external@cisco.com
Signed-off-by: Balamurugan Selvarajan <balamsel@cisco.com>
Signed-off-by: Daniel Walker <danielwa@cisco.com>
---
drivers/net/ethernet/stmicro/stmmac/common.h | 2 +
.../net/ethernet/stmicro/stmmac/stmmac_main.c | 89 +++++++++++++------
2 files changed, 65 insertions(+), 26 deletions(-)

diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h
index 5fecc83f175b..6458ce5ec0bd 100644
--- a/drivers/net/ethernet/stmicro/stmmac/common.h
+++ b/drivers/net/ethernet/stmicro/stmmac/common.h
@@ -435,6 +435,8 @@ struct dma_features {
#define MAC_CTRL_REG 0x00000000 /* MAC Control */
#define MAC_ENABLE_TX 0x00000008 /* Transmitter Enable */
#define MAC_ENABLE_RX 0x00000004 /* Receiver Enable */
+#define MAC_FULL_DUPLEX 0x00000800
+#define MAC_PORT_SELECT 0x00008000

/* Default LPI timers */
#define STMMAC_DEFAULT_LIT_LS 0x3E8
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
index 7b8404a21544..0b31aae65f3a 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
@@ -3212,6 +3212,7 @@ static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)
bool sph_en;
u32 chan;
int ret;
+ int speed;

/* DMA initialization and SW reset */
ret = stmmac_init_dma_engine(priv);
@@ -3226,7 +3227,9 @@ static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)

/* PS and related bits will be programmed according to the speed */
if (priv->hw->pcs) {
- int speed = priv->plat->mac_port_sel_speed;
+ speed = priv->plat->mac_port_sel_speed;
+ if (priv->plat->phy_interface == PHY_INTERFACE_MODE_NA)
+ speed = SPEED_1000;

if ((speed == SPEED_10) || (speed == SPEED_100) ||
(speed == SPEED_1000)) {
@@ -3256,6 +3259,17 @@ static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)
/* Enable the MAC Rx/Tx */
stmmac_mac_set(priv, priv->ioaddr, true);

+ if (priv->plat->phy_interface == PHY_INTERFACE_MODE_NA) {
+ /*
+ * Force MAC PORT SPEED to 1000Mbps and Full Duplex.
+ */
+ u32 ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
+ ctrl |= MAC_FULL_DUPLEX;
+ ctrl &= ~(MAC_PORT_SELECT);
+ writel(ctrl, priv->ioaddr + MAC_CTRL_REG);
+ }
+
+
/* Set the HW DMA mode and the COE */
stmmac_dma_operation_mode(priv);

@@ -3291,8 +3305,14 @@ static int stmmac_hw_setup(struct net_device *dev, bool init_ptp)
}
}

- if (priv->hw->pcs)
- stmmac_pcs_ctrl_ane(priv, priv->ioaddr, 1, priv->hw->ps, 0);
+ if (priv->hw->pcs) {
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA) {
+ stmmac_pcs_ctrl_ane(priv, priv->ioaddr, 1, priv->hw->ps, 0);
+ } else {
+ /* Disable Autoneg */
+ writel(0x0, priv->ioaddr + GMAC_PCS_BASE);
+ }
+ }

/* set TX and RX rings length */
stmmac_set_rings_length(priv);
@@ -3644,12 +3664,14 @@ int stmmac_open(struct net_device *dev)
priv->hw->pcs != STMMAC_PCS_RTBI &&
(!priv->hw->xpcs ||
xpcs_get_an_mode(priv->hw->xpcs, mode) != DW_AN_C73)) {
- ret = stmmac_init_phy(dev);
- if (ret) {
- netdev_err(priv->dev,
- "%s: Cannot attach to PHY (error: %d)\n",
- __func__, ret);
- goto init_phy_error;
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA) {
+ ret = stmmac_init_phy(dev);
+ if (ret) {
+ netdev_err(priv->dev,
+ "%s: Cannot attach to PHY (error: %d)\n",
+ __func__, ret);
+ goto init_phy_error;
+ }
}
}

@@ -3705,7 +3727,8 @@ int stmmac_open(struct net_device *dev)

stmmac_init_coalesce(priv);

- phylink_start(priv->phylink);
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA)
+ phylink_start(priv->phylink);
/* We may have called phylink_speed_down before */
phylink_speed_up(priv->phylink);

@@ -3716,10 +3739,14 @@ int stmmac_open(struct net_device *dev)
stmmac_enable_all_queues(priv);
netif_tx_start_all_queues(priv->dev);

+ if (priv->plat->phy_interface == PHY_INTERFACE_MODE_NA)
+ netif_carrier_on(dev);
+
return 0;

irq_error:
- phylink_stop(priv->phylink);
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA)
+ phylink_stop(priv->phylink);

for (chan = 0; chan < priv->plat->tx_queues_to_use; chan++)
hrtimer_cancel(&priv->tx_queue[chan].txtimer);
@@ -3728,7 +3755,8 @@ int stmmac_open(struct net_device *dev)
init_error:
free_dma_desc_resources(priv);
dma_desc_error:
- phylink_disconnect_phy(priv->phylink);
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA)
+ phylink_disconnect_phy(priv->phylink);
init_phy_error:
pm_runtime_put(priv->device);
return ret;
@@ -3758,8 +3786,10 @@ int stmmac_release(struct net_device *dev)
if (device_may_wakeup(priv->device))
phylink_speed_down(priv->phylink, false);
/* Stop and disconnect the PHY */
- phylink_stop(priv->phylink);
- phylink_disconnect_phy(priv->phylink);
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA) {
+ phylink_stop(priv->phylink);
+ phylink_disconnect_phy(priv->phylink);
+ }

stmmac_disable_all_queues(priv);

@@ -6986,12 +7016,15 @@ int stmmac_dvr_probe(struct device *device,
if (priv->hw->pcs != STMMAC_PCS_TBI &&
priv->hw->pcs != STMMAC_PCS_RTBI) {
/* MDIO bus Registration */
- ret = stmmac_mdio_register(ndev);
- if (ret < 0) {
- dev_err(priv->device,
- "%s: MDIO bus (id: %d) registration failed",
- __func__, priv->plat->bus_id);
- goto error_mdio_register;
+
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA) {
+ ret = stmmac_mdio_register(ndev);
+ if (ret < 0) {
+ dev_err(priv->device,
+ "%s: MDIO bus (id: %d) registration failed",
+ __func__, priv->plat->bus_id);
+ goto error_mdio_register;
+ }
}
}

@@ -7004,10 +7037,12 @@ int stmmac_dvr_probe(struct device *device,
goto error_xpcs_setup;
}

- ret = stmmac_phy_setup(priv);
- if (ret) {
- netdev_err(ndev, "failed to setup phy (%d)\n", ret);
- goto error_phy_setup;
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA) {
+ ret = stmmac_phy_setup(priv);
+ if (ret) {
+ netdev_err(ndev, "failed to setup phy (%d)\n", ret);
+ goto error_phy_setup;
+ }
}

ret = register_netdev(ndev);
@@ -7039,11 +7074,13 @@ int stmmac_dvr_probe(struct device *device,
error_serdes_powerup:
unregister_netdev(ndev);
error_netdev_register:
- phylink_destroy(priv->phylink);
+ if (priv->plat->phy_interface != PHY_INTERFACE_MODE_NA)
+ phylink_destroy(priv->phylink);
error_xpcs_setup:
error_phy_setup:
if (priv->hw->pcs != STMMAC_PCS_TBI &&
- priv->hw->pcs != STMMAC_PCS_RTBI)
+ priv->hw->pcs != STMMAC_PCS_RTBI &&
+ priv->plat->phy_interface != PHY_INTERFACE_MODE_NA)
stmmac_mdio_unregister(ndev);
error_mdio_register:
stmmac_napi_del(ndev);
--
2.25.1
\
 
 \ /
  Last update: 2021-07-30 01:52    [W:0.079 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site