Messages in this thread | | | From | Gregory CLEMENT <> | Subject | Re: [PATCH v7 0/5] DTS updates for Marvell Armada CN913x platforms | Date | Fri, 23 Jul 2021 14:58:37 +0200 |
| |
Hi Kosta,
> From: Konstantin Porotchkin <kostap@marvell.com> > > This patch series contains the following changes/fixes: > 1. Add support for Armada CN913x Development Board topology "B" > 2. Add support for Armada CN913x Reference Design boards (CRB) > 3. Fixes the NAND paritioninig scheme in DTS eliminating gap between > consecutive partitions > 4. Fix 10Gb ports PHY mode names > > v2: > - extract common nodes from DB boards to separate DTSI files > - disable eth2 on CRB boards until the required phy mode support is added > - mention the switch part ID in CRB board description > > v3: > - do not rename setup A DTS files for DB variants > - fix a couple of wrong include names > > v4: > - Rebase on top of Linus master branch (v5.11-rc7) > - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC) > - Add cd-gpio entry to CP0 SDHCI for SD card support > - Add a comment to CN9130-CRB patch about the required defconfig > changes for supporting the onboard i2c expander > - Add Stefan's patch to enable 10G port on CN9130-DB platforms > > v5: > - Extend enablement of 10G port to CN9131-DB platform > > v6: > - Rebased on top of 5.13-rc, merging UTMI settings > (requested by Gregory Clement) > > v7: > - Remove documentation patch fixing CP11X references in PHY binding document > - Change Armada's family 10Gb port phy mode names from 10gbase-kr to 10gbase-r > > Konstantin Porotchkin (4): > arch/arm64/boot/dts/marvell: fix NAND partitioning scheme > arm64: dts: cn913x: add device trees for topology B boards > arm64: dts: add support for Marvell cn9130-crb platform > arch/arm64: dts: change 10gbase-kr to 10gbase-r in Armada > > Stefan Chulski (1): > dts: marvell: Enable 10G interfaces on 9130-DB and 9131-DB boards >
Series applied on mvebu/dt64
Thanks,
Gregory
> arch/arm64/boot/dts/marvell/Makefile | 5 + > .../arm64/boot/dts/marvell/armada-7040-db.dts | 2 +- > .../arm64/boot/dts/marvell/armada-8040-db.dts | 4 +- > arch/arm64/boot/dts/marvell/cn9130-crb-A.dts | 38 ++ > arch/arm64/boot/dts/marvell/cn9130-crb-B.dts | 46 ++ > arch/arm64/boot/dts/marvell/cn9130-crb.dtsi | 222 ++++++++++ > arch/arm64/boot/dts/marvell/cn9130-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9130-db.dts | 403 +---------------- > arch/arm64/boot/dts/marvell/cn9130-db.dtsi | 410 ++++++++++++++++++ > arch/arm64/boot/dts/marvell/cn9131-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9131-db.dts | 197 +-------- > arch/arm64/boot/dts/marvell/cn9131-db.dtsi | 206 +++++++++ > arch/arm64/boot/dts/marvell/cn9132-db-B.dts | 22 + > arch/arm64/boot/dts/marvell/cn9132-db.dts | 218 +--------- > arch/arm64/boot/dts/marvell/cn9132-db.dtsi | 227 ++++++++++ > 15 files changed, 1241 insertions(+), 803 deletions(-) > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts > create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi > > -- > 2.17.1 >
-- Gregory Clement, Bootlin Embedded Linux and Kernel engineering http://bootlin.com
| |