lkml.org 
[lkml]   [2021]   [Jul]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH 3/4] dt-bindings: iio: imu: add bosch BNO055 serdev driver bindings
On Thu, 15 Jul 2021 16:17:41 +0200
Andrea Merello <andrea.merello@gmail.com> wrote:

> Introduce new documentation file for the BNO055 serdev driver that will
dt bindings are for the device not the driver (so don't mention driver
in the binding or the patch description).

> be included in next patches of this same series
>
> Signed-off-by: Andrea Merello <andrea.merello@iit.it>
> Cc: Andrea Merello <andrea.merello@gmail.com>
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Matt Ranostay <matt.ranostay@konsulko.com>
> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> Cc: Vlad Dogaru <vlad.dogaru@intel.com>
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-iio@vger.kernel.org
> ---
> .../bindings/iio/imu/bosch,bno055-serial.yaml | 40 +++++++++++++++++++
> 1 file changed, 40 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/iio/imu/bosch,bno055-serial.yaml
>
> diff --git a/Documentation/devicetree/bindings/iio/imu/bosch,bno055-serial.yaml b/Documentation/devicetree/bindings/iio/imu/bosch,bno055-serial.yaml
> new file mode 100644
> index 000000000000..743c784ebc94
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/iio/imu/bosch,bno055-serial.yaml

Better to have just one doc covering this interface and i2c if that gets added.

> @@ -0,0 +1,40 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/iio/imu/bosch,bno055-serial.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Serial-attached Bosch BNO055
> +
> +maintainers:
> + - Jonathan Cameron <jic23@kernel.org>

That's just mean! I have plenty of these to look after already! Joking
aside, you'd be a better maintainer for this than me as more likely
to pay attention.

> +
> +description: |
> + Inertial Measurement Unit with Accelerometer, Gyroscope, Magnetometer and
> + internal MCU for sensor fusion
> + https://www.bosch-sensortec.com/products/smart-sensors/bno055/
> +
> +properties:
> + compatible:
> + enum:
> + - bosch,bno055-serial
> +
> + reset-gpios:
> + maxItems: 1
> +
> + clocks:
> + maxItems: 1
> +
> +required:
> + - compatible
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> + bno055 {

name needs to be the one for the device type found in the device tree spec or
if it's not there, something in same 'spirit'. Probably imu here

> + compatible = "bosch,bno055-serial";
Don't need the -serial. It will bind based on the bus this is under.
Speaking of which, it's normal to provide that bus info as part of the example.
See for example chemical/sensiron,scd30.yaml

> + reset-gpios = <&gpio0 54 GPIO_ACTIVE_LOW>;
> + clocks = <&imu_clk>;
> + };

\
 
 \ /
  Last update: 2021-07-17 17:37    [W:0.365 / U:0.468 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site