lkml.org 
[lkml]   [2021]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 4/4] PCIe: qcom: Add support to control pipe clk src
On Fri 16 Jul 10:06 CDT 2021, Bjorn Helgaas wrote:

> Run this:
>
> $ git log --oneline drivers/pci/controller/dwc/pcie-qcom.c
>
> and make your subject match the style and structure (in particular,
> s/PCIe/PCI/). In this case, maybe something like this?
>
> PCI: qcom: Switch sc7280 gcc_pcie_1_pipe_clk_src after PHY init
>
> On Fri, Jul 16, 2021 at 07:28:47PM +0530, Prasad Malisetty wrote:
> > This is a new requirement for sc7280 SoC.
> > To enable gdsc gcc_pcie_1_pipe_clk_src should be TCXO.
> > after PHY initialization gcc_pcie_1_pipe_clk_src needs
> > to switch from TCXO to gcc_pcie_1_pipe_clk.
>
> This says what *needs* to happen, but it doesn't actually say what
> this patch *does*. I think it's something like:
>
> On the sc7280 SoC, the clock source for pcie_1_pipe must be the TCXO
> while gdsc is enabled. But after the PHY is initialized, the clock
> source must be switched to gcc_pcie_1_pipe_clk.
>
> On sc7280, switch gcc_pcie_1_pipe_clk_src from TCXO to
> gcc_pcie_1_pipe_clk after the PHY has been initialized.
>
> Nits: Rewrap to fill 75 columns or so. Add blank lines between
> paragraphs. Start sentences with capital letter.
>
> > Signed-off-by: Prasad Malisetty <pmaliset@codeaurora.org>
> > ---
> > drivers/pci/controller/dwc/pcie-qcom.c | 22 ++++++++++++++++++++++
> > 1 file changed, 22 insertions(+)
> >
> > diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> > index 8a7a300..9e0e4ab 100644
> > --- a/drivers/pci/controller/dwc/pcie-qcom.c
> > +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> > @@ -166,6 +166,9 @@ struct qcom_pcie_resources_2_7_0 {
> > struct regulator_bulk_data supplies[2];
> > struct reset_control *pci_reset;
> > struct clk *pipe_clk;
> > + struct clk *gcc_pcie_1_pipe_clk_src;
> > + struct clk *phy_pipe_clk;
> > + struct clk *ref_clk_src;
> > };
> >
> > union qcom_pcie_resources {
> > @@ -1167,6 +1170,20 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
> > if (ret < 0)
> > return ret;
> >
> > + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280")) {
> > + res->gcc_pcie_1_pipe_clk_src = devm_clk_get(dev, "pipe_mux");
> > + if (IS_ERR(res->gcc_pcie_1_pipe_clk_src))
> > + return PTR_ERR(res->gcc_pcie_1_pipe_clk_src);
> > +
> > + res->phy_pipe_clk = devm_clk_get(dev, "phy_pipe");
> > + if (IS_ERR(res->phy_pipe_clk))
> > + return PTR_ERR(res->phy_pipe_clk);
> > +
> > + res->ref_clk_src = devm_clk_get(dev, "ref");
> > + if (IS_ERR(res->ref_clk_src))
> > + return PTR_ERR(res->ref_clk_src);
>
> Not clear why ref_clk_src is here, since it's not used anywhere. If
> it's not necessary here, drop it and add it in a future patch that
> uses it.
>
> > + }
> > +
> > res->pipe_clk = devm_clk_get(dev, "pipe");
> > return PTR_ERR_OR_ZERO(res->pipe_clk);
> > }
> > @@ -1255,6 +1272,11 @@ static void qcom_pcie_deinit_2_7_0(struct qcom_pcie *pcie)
> > static int qcom_pcie_post_init_2_7_0(struct qcom_pcie *pcie)
> > {
> > struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
> > + struct dw_pcie *pci = pcie->pci;
> > + struct device *dev = pci->dev;
> > +
> > + if (of_device_is_compatible(dev->of_node, "qcom,pcie-sc7280"))
>
> Using of_device_is_compatible() follows existing style in the driver,
> which is good. But I'm not sure that's good style in general because
> it's a little repetitious and wasteful.
>

Following the style is good, but up until the recent sm8250 addition it
was just a hack to deal with legacy platforms that we don't know the
exact details about.

But, all platforms I know of has the pipe_clk from the PHY fed into the
pipe_clk_src mux in the gcc block and then ends up in the PCIe
controller. As such, I suspect that the pipe_clk handling should be moved
to the common code path of the driver and there's definitely no harm in
making sure that the pipe_clk_src mux is explicitly configured on
existing platforms (at least all 2.7.0 based ones).

> qcom_pcie_probe() already calls of_device_get_match_data(), which does
> basically the same thing as of_device_is_compatible(), so I think we
> could take better advantage of that by augmenting struct qcom_pcie_ops
> with these device-specific details.
>

I agree.

Regards,
Bjorn

> Some drivers that use this strategy:
>
> drivers/pci/controller/cadence/pci-j721e.c
> drivers/pci/controller/dwc/pci-imx6.c
> drivers/pci/controller/dwc/pci-layerscape.c
> drivers/pci/controller/dwc/pci-layerscape-ep.c
> drivers/pci/controller/dwc/pcie-tegra194.c
> drivers/pci/controller/pci-ftpci100.c
> drivers/pci/controller/pcie-brcmstb.c
> drivers/pci/controller/pcie-mediatek.c
>
> > + clk_set_parent(res->gcc_pcie_1_pipe_clk_src, res->phy_pipe_clk);
> >
> > return clk_prepare_enable(res->pipe_clk);
> > }
> > --
> > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> > a Linux Foundation Collaborative Project
> >

\
 
 \ /
  Last update: 2021-07-16 22:40    [W:0.123 / U:0.112 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site