lkml.org 
[lkml]   [2021]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v13 1/9] staging: hi6421-spmi-pmic: rename GPIO IRQ OF node
Em Wed, 14 Jul 2021 07:36:43 -0600
Rob Herring <robh@kernel.org> escreveu:

> On Wed, Jul 14, 2021 at 3:13 AM Mauro Carvalho Chehab
> <mchehab+huawei@kernel.org> wrote:
> >
> > Instead of using the standard name ("gpios"), use "interrupts".
> >
> > Suggested-by: Rob Herring <robh@kernel.org>
> > Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
> > ---
> > drivers/staging/hikey9xx/hi6421-spmi-pmic.c | 2 +-
> > drivers/staging/hikey9xx/hisilicon,hi6421-spmi-pmic.yaml | 4 ++--
> > 2 files changed, 3 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/staging/hikey9xx/hi6421-spmi-pmic.c b/drivers/staging/hikey9xx/hi6421-spmi-pmic.c
> > index 35ef3d4c760b..9a7e095246f7 100644
> > --- a/drivers/staging/hikey9xx/hi6421-spmi-pmic.c
> > +++ b/drivers/staging/hikey9xx/hi6421-spmi-pmic.c
> > @@ -233,7 +233,7 @@ static int hi6421_spmi_pmic_probe(struct spmi_device *pdev)
> >
> > ddata->dev = dev;
> >
> > - ddata->gpio = of_get_gpio(np, 0);
> > + ddata->gpio = of_get_named_gpio_flags(np, "interrupts", 0, NULL);
>
> It's an interrupt, you should be using platform_get_irq() and
> devm_request_irq().
>
> In general, you should not be using of_get_* for any resources, but
> use the firmware agnostic flavors.

I've no idea how to convert to use platform_get_irq().

I tried to replace the logic:

priv->gpio = of_get_gpio(np, 0);
if (priv->gpio < 0)
return priv->gpio;

if (!gpio_is_valid(priv->gpio))
return -EINVAL;

ret = devm_gpio_request_one(dev, priv->gpio, GPIOF_IN, "pmic");
if (ret < 0) {
dev_err(dev, "Failed to request gpio%d\n", priv->gpio);
return ret;
}

Into:

priv->irq = platform_get_irq(pdev, 0);

But it didn't work (I also tried the platform_get_irq_byname):

[ 1.109586] hi6421v600-irq hi6421v600-irq: hi6421v600_irq_probe:
[ 1.115676] hi6421v600-irq hi6421v600-irq: IRQ index 0 not found
[ 1.121751] hi6421v600-irq hi6421v600-irq: Error -6 when getting IRQs

The original DT schema as:

gpios = <&gpio28 0 0>;

Based on your past review, this was replaced by:

interrupts = <&gpio28 0 0>;


What am I missing?

Thanks,
Mauro

\
 
 \ /
  Last update: 2021-07-16 16:46    [W:0.987 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site