lkml.org 
[lkml]   [2021]   [Jul]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH V1 1/3] dt-bindings: net: fec: convert fsl,*fec bindings to yaml
Date
In order to automate the verification of DT nodes convert fsl-fec.txt to
fsl,fec.yaml, and pass binding check with below command.

$ make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- dt_binding_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/fsl,fec.yaml
DTEX Documentation/devicetree/bindings/net/fsl,fec.example.dts
DTC Documentation/devicetree/bindings/net/fsl,fec.example.dt.yaml
CHECK Documentation/devicetree/bindings/net/fsl,fec.example.dt.yaml

Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
---
.../devicetree/bindings/net/fsl,fec.yaml | 213 ++++++++++++++++++
.../devicetree/bindings/net/fsl-fec.txt | 95 --------
2 files changed, 213 insertions(+), 95 deletions(-)
create mode 100644 Documentation/devicetree/bindings/net/fsl,fec.yaml
delete mode 100644 Documentation/devicetree/bindings/net/fsl-fec.txt

diff --git a/Documentation/devicetree/bindings/net/fsl,fec.yaml b/Documentation/devicetree/bindings/net/fsl,fec.yaml
new file mode 100644
index 000000000000..7fa11f6622b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/fsl,fec.yaml
@@ -0,0 +1,213 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/fsl,fec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale Fast Ethernet Controller (FEC)
+
+maintainers:
+ - Joakim Zhang <qiangqing.zhang@nxp.com>
+
+allOf:
+ - $ref: ethernet-controller.yaml#
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - fsl,imx25-fec
+ - fsl,imx27-fec
+ - fsl,imx28-fec
+ - fsl,imx6q-fec
+ - fsl,mvf600-fec
+ - items:
+ - enum:
+ - fsl,imx53-fec
+ - fsl,imx6sl-fec
+ - const: fsl,imx25-fec
+ - items:
+ - enum:
+ - fsl,imx35-fec
+ - fsl,imx51-fec
+ - const: fsl,imx27-fec
+ - items:
+ - enum:
+ - fsl,imx6ul-fec
+ - fsl,imx6sx-fec
+ - const: fsl,imx6q-fec
+ - items:
+ - enum:
+ - fsl,imx7d-fec
+ - const: fsl,imx6sx-fec
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ minItems: 1
+ maxItems: 4
+
+ interrupt-names:
+ description:
+ Names of the interrupts listed in interrupts property in the same order.
+ The defaults if not specified are
+ __Number of interrupts__ __Default__
+ 1 "int0"
+ 2 "int0", "pps"
+ 3 "int0", "int1", "int2"
+ 4 "int0", "int1", "int2", "pps"
+ The order may be changed as long as they correspond to the interrupts
+ property. Currently, only i.mx7 uses "int1" and "int2". They correspond to
+ tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts.
+ For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse
+ per second interrupt associated with 1588 precision time protocol(PTP).
+
+ clocks:
+ minItems: 2
+ maxItems: 5
+ description:
+ The "ipg", for MAC ipg_clk_s, ipg_clk_mac_s that are for register accessing.
+ The "ahb", for MAC ipg_clk, ipg_clk_mac that are bus clock.
+ The "ptp"(option), for IEEE1588 timer clock that requires the clock.
+ The "enet_clk_ref"(option), for MAC transmit/receiver reference clock like
+ RGMII TXC clock or RMII reference clock. It depends on board design,
+ the clock is required if RGMII TXC and RMII reference clock source from
+ SOC internal PLL.
+ The "enet_out"(option), output clock for external device, like supply clock
+ for PHY. The clock is required if PHY clock source from SOC.
+
+ clock-names:
+ minItems: 2
+ maxItems: 5
+ contains:
+ enum:
+ - ipg
+ - ahb
+ - ptp
+ - enet_clk_ref
+ - enet_out
+
+ phy-mode: true
+
+ phy-handle: true
+
+ fixed-link: true
+
+ local-mac-address: true
+
+ mac-address: true
+
+ phy-supply:
+ description:
+ Regulator that powers the Ethernet PHY.
+
+ fsl,num-tx-queues:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The property is valid for enet-avb IP, which supports hw multi queues.
+ Should specify the tx queue number, otherwise set tx queue number to 1.
+
+ fsl,num-rx-queues:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ The property is valid for enet-avb IP, which supports hw multi queues.
+ Should specify the rx queue number, otherwise set rx queue number to 1.
+
+ fsl,magic-packet:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ If present, indicates that the hardware supports waking up via magic packet.
+
+ fsl,err006687-workaround-present:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ If present indicates that the system has the hardware workaround for
+ ERR006687 applied and does not need a software workaround.
+
+ fsl,stop-mode:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description:
+ Register bits of stop mode control, the format is <&gpr req_gpr req_bit>.
+ gpr is the phandle to general purpose register node.
+ req_gpr is the gpr register offset for ENET stop request.
+ req_bit is the gpr bit offset for ENET stop request.
+
+ mdio:
+ type: object
+ description:
+ Specifies the mdio bus in the FEC, used as a container for phy nodes.
+
+ # Deprecated optional properties:
+ # To avoid these, create a phy node according to ethernet-phy.yaml in the same
+ # directory, and point the FEC's "phy-handle" property to it. Then use
+ # the phy's reset binding, again described by ethernet-phy.yaml.
+
+ phy-reset-gpios:
+ deprecated: true
+ description:
+ Should specify the gpio for phy reset.
+
+ phy-reset-duration:
+ deprecated: true
+ description:
+ Reset duration in milliseconds. Should present only if property
+ "phy-reset-gpios" is available. Missing the property will have the
+ duration be 1 millisecond. Numbers greater than 1000 are invalid
+ and 1 millisecond will be used instead.
+
+ phy-reset-active-high:
+ deprecated: true
+ description:
+ If present then the reset sequence using the GPIO specified in the
+ "phy-reset-gpios" property is reversed (H=reset state, L=operation state).
+
+ phy-reset-post-delay:
+ deprecated: true
+ description:
+ Post reset delay in milliseconds. If present then a delay of phy-reset-post-delay
+ milliseconds will be observed after the phy-reset-gpios has been toggled.
+ Can be omitted thus no delay is observed. Delay is in range of 1ms to 1000ms.
+ Other delays are invalid.
+
+required:
+ - compatible
+ - reg
+ - interrupts
+
+# FIXME: We had better set additionalProperties to false to avoid invalid or at
+# least undocumented properties. However, PHY may have a deprecated option to
+# place PHY OF properties in the MAC node, such as Micrel PHY, and we can find
+# these boards which is based on i.MX6QDL.
+additionalProperties: true
+
+examples:
+ - |
+ ethernet@83fec000 {
+ compatible = "fsl,imx51-fec", "fsl,imx27-fec";
+ reg = <0x83fec000 0x4000>;
+ interrupts = <87>;
+ phy-mode = "mii";
+ phy-reset-gpios = <&gpio2 14 0>;
+ phy-supply = <&reg_fec_supply>;
+ };
+
+ ethernet@83fed000 {
+ compatible = "fsl,imx51-fec", "fsl,imx27-fec";
+ reg = <0x83fed000 0x4000>;
+ interrupts = <87>;
+ phy-mode = "mii";
+ phy-reset-gpios = <&gpio2 14 0>;
+ phy-supply = <&reg_fec_supply>;
+ phy-handle = <&ethphy0>;
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0>;
+ };
+ };
+ };
diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt
deleted file mode 100644
index 9b543789cd52..000000000000
--- a/Documentation/devicetree/bindings/net/fsl-fec.txt
+++ /dev/null
@@ -1,95 +0,0 @@
-* Freescale Fast Ethernet Controller (FEC)
-
-Required properties:
-- compatible : Should be "fsl,<soc>-fec"
-- reg : Address and length of the register set for the device
-- interrupts : Should contain fec interrupt
-- phy-mode : See ethernet.txt file in the same directory
-
-Optional properties:
-- phy-supply : regulator that powers the Ethernet PHY.
-- phy-handle : phandle to the PHY device connected to this device.
-- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
- Use instead of phy-handle.
-- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports
- hw multi queues. Should specify the tx queue number, otherwise set tx queue
- number to 1.
-- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports
- hw multi queues. Should specify the rx queue number, otherwise set rx queue
- number to 1.
-- fsl,magic-packet : If present, indicates that the hardware supports waking
- up via magic packet.
-- fsl,err006687-workaround-present: If present indicates that the system has
- the hardware workaround for ERR006687 applied and does not need a software
- workaround.
-- fsl,stop-mode: register bits of stop mode control, the format is
- <&gpr req_gpr req_bit>.
- gpr is the phandle to general purpose register node.
- req_gpr is the gpr register offset for ENET stop request.
- req_bit is the gpr bit offset for ENET stop request.
- -interrupt-names: names of the interrupts listed in interrupts property in
- the same order. The defaults if not specified are
- __Number of interrupts__ __Default__
- 1 "int0"
- 2 "int0", "pps"
- 3 "int0", "int1", "int2"
- 4 "int0", "int1", "int2", "pps"
- The order may be changed as long as they correspond to the interrupts
- property. Currently, only i.mx7 uses "int1" and "int2". They correspond to
- tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts.
- For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse
- per second interrupt associated with 1588 precision time protocol(PTP).
-
-Optional subnodes:
-- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes
- according to phy.txt in the same directory
-
-Deprecated optional properties:
- To avoid these, create a phy node according to phy.txt in the same
- directory, and point the fec's "phy-handle" property to it. Then use
- the phy's reset binding, again described by phy.txt.
-- phy-reset-gpios : Should specify the gpio for phy reset
-- phy-reset-duration : Reset duration in milliseconds. Should present
- only if property "phy-reset-gpios" is available. Missing the property
- will have the duration be 1 millisecond. Numbers greater than 1000 are
- invalid and 1 millisecond will be used instead.
-- phy-reset-active-high : If present then the reset sequence using the GPIO
- specified in the "phy-reset-gpios" property is reversed (H=reset state,
- L=operation state).
-- phy-reset-post-delay : Post reset delay in milliseconds. If present then
- a delay of phy-reset-post-delay milliseconds will be observed after the
- phy-reset-gpios has been toggled. Can be omitted thus no delay is
- observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
-
-Example:
-
-ethernet@83fec000 {
- compatible = "fsl,imx51-fec", "fsl,imx27-fec";
- reg = <0x83fec000 0x4000>;
- interrupts = <87>;
- phy-mode = "mii";
- phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */
- local-mac-address = [00 04 9F 01 1B B9];
- phy-supply = <&reg_fec_supply>;
-};
-
-Example with phy specified:
-
-ethernet@83fec000 {
- compatible = "fsl,imx51-fec", "fsl,imx27-fec";
- reg = <0x83fec000 0x4000>;
- interrupts = <87>;
- phy-mode = "mii";
- phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */
- local-mac-address = [00 04 9F 01 1B B9];
- phy-supply = <&reg_fec_supply>;
- phy-handle = <&ethphy>;
- mdio {
- clock-frequency = <5000000>;
- ethphy: ethernet-phy@6 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <6>;
- max-speed = <100>;
- };
- };
-};
--
2.17.1
\
 
 \ /
  Last update: 2021-07-16 12:30    [W:0.933 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site