lkml.org 
[lkml]   [2021]   [Jul]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH 5.13 210/266] mmc: core: Allow UHS-I voltage switch for SDSC cards if supported
    Date
    From: Christian Löhle <CLoehle@hyperstone.com>

    commit 09247e110b2efce3a104e57e887c373e0a57a412 upstream.

    While initializing an UHS-I SD card, the mmc core first tries to switch to
    1.8V I/O voltage, before it continues to change the settings for the bus
    speed mode.

    However, the current behaviour in the mmc core is inconsistent and doesn't
    conform to the SD spec. More precisely, an SD card that supports UHS-I must
    set both the SD_OCR_CCS bit and the SD_OCR_S18R bit in the OCR register
    response. When switching to 1.8V I/O the mmc core correctly checks both of
    the bits, but only the SD_OCR_S18R bit when changing the settings for bus
    speed mode.

    Rather than actually fixing the code to confirm to the SD spec, let's
    deliberately deviate from it by requiring only the SD_OCR_S18R bit for both
    parts. This enables us to support UHS-I for SDSC cards (outside spec),
    which is actually being supported by some existing SDSC cards. Moreover,
    this fixes the inconsistent behaviour.

    Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
    Link: https://lore.kernel.org/r/CWXP265MB26803AE79E0AD5ED083BF2A6C4529@CWXP265MB2680.GBRP265.PROD.OUTLOOK.COM
    Cc: stable@vger.kernel.org
    [Ulf: Rewrote commit message and comments to clarify the changes]
    Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
    Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

    ---
    drivers/mmc/core/sd.c | 10 ++++++----
    1 file changed, 6 insertions(+), 4 deletions(-)

    --- a/drivers/mmc/core/sd.c
    +++ b/drivers/mmc/core/sd.c
    @@ -847,11 +847,13 @@ try_again:
    return err;

    /*
    - * In case CCS and S18A in the response is set, start Signal Voltage
    - * Switch procedure. SPI mode doesn't support CMD11.
    + * In case the S18A bit is set in the response, let's start the signal
    + * voltage switch procedure. SPI mode doesn't support CMD11.
    + * Note that, according to the spec, the S18A bit is not valid unless
    + * the CCS bit is set as well. We deliberately deviate from the spec in
    + * regards to this, which allows UHS-I to be supported for SDSC cards.
    */
    - if (!mmc_host_is_spi(host) && rocr &&
    - ((*rocr & 0x41000000) == 0x41000000)) {
    + if (!mmc_host_is_spi(host) && rocr && (*rocr & 0x01000000)) {
    err = mmc_set_uhs_voltage(host, pocr);
    if (err == -EAGAIN) {
    retries--;

    \
     
     \ /
      Last update: 2021-07-15 21:47    [W:2.517 / U:0.004 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site