lkml.org 
[lkml]   [2021]   [Jul]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [RFC PATH 2/2] gpio: starfive-jh7100: Add StarFive JH7100 GPIO driver
Hi Drew


On Thu, Jul 1, 2021 at 8:25 AM Drew Fustini <drew@beagleboard.org> wrote:
>
> Add GPIO driver for the StarFive JH7100 SoC [1] used on the
> BeagleV Starlight JH7100 board [2].
>
> [1] https://github.com/starfive-tech/beaglev_doc/
> [2] https://github.com/beagleboard/beaglev-starlight
>
> Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
> Signed-off-by: Huan Feng <huan.feng@starfivetech.com>
> Signed-off-by: Drew Fustini <drew@beagleboard.org>
> ---
> MAINTAINERS | 8 +
> drivers/gpio/Kconfig | 8 +
> drivers/gpio/Makefile | 1 +
> drivers/gpio/gpio-starfive-jh7100.c | 425 ++++++++++++++++++++++++++++
> 4 files changed, 442 insertions(+)
> create mode 100644 drivers/gpio/gpio-starfive-jh7100.c

[...]

> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index d7c81e1611a4..939922eaf5f3 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -132,6 +132,7 @@ obj-$(CONFIG_GPIO_SAMA5D2_PIOBU) += gpio-sama5d2-piobu.o
> obj-$(CONFIG_GPIO_SCH311X) += gpio-sch311x.o
> obj-$(CONFIG_GPIO_SCH) += gpio-sch.o
> obj-$(CONFIG_GPIO_SIFIVE) += gpio-sifive.o
> +obj-$(CONFIG_GPIO_STARFIVE_JH7100) += gpio-starfive-jh7100.o
Sort in alphabetical order.

> obj-$(CONFIG_GPIO_SIOX) += gpio-siox.o
> obj-$(CONFIG_GPIO_SL28CPLD) += gpio-sl28cpld.o
> obj-$(CONFIG_GPIO_SODAVILLE) += gpio-sodaville.o
> diff --git a/drivers/gpio/gpio-starfive-jh7100.c b/drivers/gpio/gpio-starfive-jh7100.c
> new file mode 100644
> index 000000000000..b94ebfe9eaf7
> --- /dev/null
> +++ b/drivers/gpio/gpio-starfive-jh7100.c
> @@ -0,0 +1,425 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * GPIO driver for StarFive JH7100 SoC
> + *
> + * Copyright (C) 2020 Shanghai StarFive Technology Co., Ltd.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/gpio/driver.h>
> +#include <linux/platform_device.h>
> +#include <linux/spinlock.h>
Include files sort in alphabetical orde too.

> +
> +/*
> + * refer to Section 12. GPIO Registers in JH7100 datasheet:
> + * https://github.com/starfive-tech/beaglev_doc
> + */
> +
> +/* global enable */
> +#define GPIO_EN 0x0
> +
> +/* interrupt type */
> +#define GPIO_IS_LOW 0x10
> +#define GPIO_IS_HIGH 0x14
> +
> +/* edge trigger interrupt type */
> +#define GPIO_IBE_LOW 0x18
> +#define GPIO_IBE_HIGH 0x1c
> +
> +/* edge trigger interrupt polarity */
> +#define GPIO_IEV_LOW 0x20
> +#define GPIO_IEV_HIGH 0x24
> +
> +/* interrupt max */
> +#define GPIO_IE_LOW 0x28
> +#define GPIO_IE_HIGH 0x2c
> +
> +/* clear edge-triggered interrupt */
> +#define GPIO_IC_LOW 0x30
> +#define GPIO_IC_HIGH 0x34
> +
> +/* edge-triggered interrupt status (read-only) */
> +#define GPIO_RIS_LOW 0x38
> +#define GPIO_RIS_HIGH 0x3c
> +
> +/* interrupt status after masking (read-only) */
> +#define GPIO_MIS_LOW 0x40
> +#define GPIO_MIS_HIGH 0x44
> +
> +/* data value of gpio */
> +#define GPIO_DIN_LOW 0x48
> +#define GPIO_DIN_HIGH 0x4c
> +
> +/* GPIO0_DOUT_CFG is 0x50, GPIOn_DOUT_CFG is 0x50+(n*8) */
> +#define GPIO_DOUT_X_REG 0x50
> +
> +/* GPIO0_DOEN_CFG is 0x54, GPIOn_DOEN_CFG is 0x54+(n*8) */
> +#define GPIO_DOEN_X_REG 0x54
> +
> +#define MAX_GPIO 64
> +
> +struct starfive_gpio {
> + raw_spinlock_t lock;
> + void __iomem *base;
> + struct gpio_chip gc;
> + unsigned long enabled;
> + unsigned int trigger[MAX_GPIO];
> + unsigned int irq_parent[MAX_GPIO];
> +};
> +
> +static int starfive_direction_input(struct gpio_chip *gc, unsigned int offset)
> +{
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + unsigned long flags;
> +
> + if (offset >= gc->ngpio)
> + return -EINVAL;
> +
> + raw_spin_lock_irqsave(&chip->lock, flags);
> + writel_relaxed(0x1, chip->base + GPIO_DOEN_X_REG + offset * 8);
> + raw_spin_unlock_irqrestore(&chip->lock, flags);
> +
> + return 0;
> +}
> +
> +static int starfive_direction_output(struct gpio_chip *gc, unsigned int offset, int value)
> +{
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + unsigned long flags;
> +
> + if (offset >= gc->ngpio)
> + return -EINVAL;
> +
> + raw_spin_lock_irqsave(&chip->lock, flags);
> + writel_relaxed(0x0, chip->base + GPIO_DOEN_X_REG + offset * 8);
> + writel_relaxed(value, chip->base + GPIO_DOUT_X_REG + offset * 8);
> + raw_spin_unlock_irqrestore(&chip->lock, flags);
> +
> + return 0;
> +}
> +
> +static int starfive_get_direction(struct gpio_chip *gc, unsigned int offset)
> +{
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> +
> + if (offset >= gc->ngpio)
> + return -EINVAL;
> +
> + return readl_relaxed(chip->base + GPIO_DOEN_X_REG + offset * 8) & 0x1;
> +}
> +
> +static int starfive_get_value(struct gpio_chip *gc, unsigned int offset)
> +{
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + int value;
> +
> + if (offset >= gc->ngpio)
> + return -EINVAL;
> +
> + if (offset < 32) {
> + value = readl_relaxed(chip->base + GPIO_DIN_LOW);
> + value = (value >> offset) & 0x1;
> + } else {
> + value = readl_relaxed(chip->base + GPIO_DIN_HIGH);
> + value = (value >> (offset - 32)) & 0x1;
> + }
> +
> + return value;
> +}
> +
> +static void starfive_set_value(struct gpio_chip *gc, unsigned int offset, int value)
> +{
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + unsigned long flags;
> +
> + if (offset >= gc->ngpio)
> + return;
> +
> + raw_spin_lock_irqsave(&chip->lock, flags);
> + writel_relaxed(value, chip->base + GPIO_DOUT_X_REG + offset * 8);
> + raw_spin_unlock_irqrestore(&chip->lock, flags);
> +}
> +
> +static void starfive_set_ie(struct starfive_gpio *chip, int offset)
> +{
> + unsigned long flags;
> + int old_value, new_value;
> + int reg_offset, index;
> +
> + if (offset < 32) {
> + reg_offset = 0;
> + index = offset;
> + } else {
> + reg_offset = 4;
> + index = offset - 32;
> + }
Quite a number of places do this checking/calculation, can move this
to a helper function.

> + raw_spin_lock_irqsave(&chip->lock, flags);
> + old_value = readl_relaxed(chip->base + GPIO_IE_LOW + reg_offset);
> + new_value = old_value | (1 << index);
> + writel_relaxed(new_value, chip->base + GPIO_IE_LOW + reg_offset);
> + raw_spin_unlock_irqrestore(&chip->lock, flags);
> +}
> +
> +static int starfive_irq_set_type(struct irq_data *d, unsigned int trigger)
> +{
> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + int offset = irqd_to_hwirq(d);
> + unsigned int reg_is, reg_ibe, reg_iev;
> + int reg_offset, index;
> +
> + if (offset < 0 || offset >= gc->ngpio)
> + return -EINVAL;
> +
> + if (offset < 32) {
> + reg_offset = 0;
> + index = offset;
> + } else {
> + reg_offset = 4;
> + index = offset - 32;
> + }
> +
> + reg_is = readl_relaxed(chip->base + GPIO_IS_LOW + reg_offset);
> + reg_ibe = readl_relaxed(chip->base + GPIO_IBE_LOW + reg_offset);
> + reg_iev = readl_relaxed(chip->base + GPIO_IEV_LOW + reg_offset);
> +
> + switch (trigger) {
> + case IRQ_TYPE_LEVEL_HIGH:
> + reg_is &= ~(1 << index);
> + reg_ibe &= ~(1 << index);
> + reg_iev |= (1 << index);
> + break;
> + case IRQ_TYPE_LEVEL_LOW:
> + reg_is &= ~(1 << index);
> + reg_ibe &= ~(1 << index);
> + reg_iev &= (1 << index);
> + break;
> + case IRQ_TYPE_EDGE_BOTH:
> + reg_is |= ~(1 << index);
> + reg_ibe |= ~(1 << index);
> + // no need to set edge type when both
Use /**/ comment style.

> + break;
> + case IRQ_TYPE_EDGE_RISING:
> + reg_is |= ~(1 << index);
> + reg_ibe &= ~(1 << index);
> + reg_iev |= (1 << index);
> + break;
> + case IRQ_TYPE_EDGE_FALLING:
> + reg_is |= ~(1 << index);
> + reg_ibe &= ~(1 << index);
> + reg_iev &= (1 << index);
> + break;
> + }
> +
> + writel_relaxed(reg_is, chip->base + GPIO_IS_LOW + reg_offset);
> + writel_relaxed(reg_ibe, chip->base + GPIO_IBE_LOW + reg_offset);
> + writel_relaxed(reg_iev, chip->base + GPIO_IEV_LOW + reg_offset);
> + chip->trigger[offset] = trigger;
> + starfive_set_ie(chip, offset);
> + return 0;
> +}
> +
> +/* chained_irq_{enter,exit} already mask the parent */
> +static void starfive_irq_mask(struct irq_data *d)
> +{
> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + unsigned int value;
> + int offset = irqd_to_hwirq(d);
> + int reg_offset, index;
> +
> + if (offset < 0 || offset >= gc->ngpio)
> + return;
> +
> + if (offset < 32) {
> + reg_offset = 0;
> + index = offset;
> + } else {
> + reg_offset = 4;
> + index = offset - 32;
> + }
> +
> + value = readl_relaxed(chip->base + GPIO_IE_LOW + reg_offset);
> + value &= ~(0x1 << index);
> + writel_relaxed(value, chip->base + GPIO_IE_LOW + reg_offset);
> +}
> +
> +static void starfive_irq_unmask(struct irq_data *d)
> +{
> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + unsigned int value;
> + int offset = irqd_to_hwirq(d);
> + int reg_offset, index;
> +
> + if (offset < 0 || offset >= gc->ngpio)
> + return;
> +
> + if (offset < 32) {
> + reg_offset = 0;
> + index = offset;
> + } else {
> + reg_offset = 4;
> + index = offset - 32;
> + }
> +
> + value = readl_relaxed(chip->base + GPIO_IE_LOW + reg_offset);
> + value |= (0x1 << index);
> + writel_relaxed(value, chip->base + GPIO_IE_LOW + reg_offset);
> +}
> +
> +static void starfive_irq_enable(struct irq_data *d)
> +{
> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + int offset = irqd_to_hwirq(d);
> +
> + starfive_irq_unmask(d);
> + assign_bit(offset, &chip->enabled, 1);
> +}
> +
> +static void starfive_irq_disable(struct irq_data *d)
> +{
> + struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
> + struct starfive_gpio *chip = gpiochip_get_data(gc);
> + int offset = irqd_to_hwirq(d) % MAX_GPIO; // must not fail
> +
> + assign_bit(offset, &chip->enabled, 0);
> + starfive_set_ie(chip, offset);
> +}
> +
> +static struct irq_chip starfive_irqchip = {
> + .name = "starfive-jh7100-gpio",
> + .irq_set_type = starfive_irq_set_type,
> + .irq_mask = starfive_irq_mask,
> + .irq_unmask = starfive_irq_unmask,
> + .irq_enable = starfive_irq_enable,
> + .irq_disable = starfive_irq_disable,
> +};
> +
> +static irqreturn_t starfive_irq_handler(int irq, void *gc)
> +{
> + int offset;
> + int reg_offset, index;
> + unsigned int value;
> + unsigned long flags;
> + struct starfive_gpio *chip = gc;
> +
> + for (offset = 0; offset < MAX_GPIO; offset++) {
> + if (offset < 32) {
> + reg_offset = 0;
> + index = offset;
> + } else {
> + reg_offset = 4;
> + index = offset - 32;
> + }
> +
> + raw_spin_lock_irqsave(&chip->lock, flags);
> + value = readl_relaxed(chip->base + GPIO_MIS_LOW + reg_offset);
> + if (value & BIT(index))
> + writel_relaxed(BIT(index), chip->base + GPIO_IC_LOW +
> + reg_offset);
> + raw_spin_unlock_irqrestore(&chip->lock, flags);
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int starfive_gpio_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct starfive_gpio *chip;
> + struct gpio_irq_chip *girq;
> + struct resource *res;
> + int irq, ret, ngpio;
> +
> + chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
> + if (!chip)
> + return -ENOMEM;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + chip->base = devm_ioremap_resource(dev, res);
Can use device managed function devm_
devm_platform_ioremap_resource(), then combile these 2 functions into
1.

> + if (IS_ERR(chip->base)) {
> + dev_err(dev, "failed to allocate device memory\n");
Perhaps change "allocate" to get or ioremap.

> + return PTR_ERR(chip->base);
> + }
> +
> + irq = platform_get_irq(pdev, 0);
> + if (irq < 0) {
> + dev_err(dev, "Cannot get IRQ resource\n");
> + return irq;
> + }
> +
> + raw_spin_lock_init(&chip->lock);
> + chip->gc.direction_input = starfive_direction_input;
> + chip->gc.direction_output = starfive_direction_output;
> + chip->gc.get_direction = starfive_get_direction;
> + chip->gc.get = starfive_get_value;
> + chip->gc.set = starfive_set_value;
> + chip->gc.base = 0;
> + chip->gc.ngpio = MAX_GPIO;
> + chip->gc.label = dev_name(dev);
> + chip->gc.parent = dev;
> + chip->gc.owner = THIS_MODULE;
> +
> + girq = &chip->gc.irq;
> + girq->chip = &starfive_irqchip;
> + girq->parent_handler = NULL;
> + girq->num_parents = 0;
> + girq->parents = NULL;
> + girq->default_type = IRQ_TYPE_NONE;
> + girq->handler = handle_simple_irq;
> +
> + ret = gpiochip_add_data(&chip->gc, chip);
Use devm_version, devm_gpiochip_add_data().

> + if (ret) {
> + dev_err(dev, "gpiochip_add_data ret=%d!\n", ret);
> + return ret;
> + }
> +
> + /* Disable all GPIO interrupts before enabling parent interrupts */
Clear any pending interrupts as well when initialization.

> + iowrite32(0, chip->base + GPIO_IE_HIGH);
> + iowrite32(0, chip->base + GPIO_IE_LOW);
> + chip->enabled = 0;
> +
> + ret = devm_request_irq(dev, irq, starfive_irq_handler, IRQF_SHARED,
> + dev_name(dev), chip);
> + if (ret) {
> + dev_err(dev, "IRQ handler registering failed (%d)\n", ret);
> + return ret;
> + }
> +
> + writel_relaxed(1, chip->base + GPIO_EN);
> +
> + dev_info(dev, "StarFive GPIO chip registered %d GPIOs\n", ngpio);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id starfive_gpio_match[] = {
> + { .compatible = "starfive,jh7100-gpio", },
> + { },
> +};
> +
> +static struct platform_driver starfive_gpio_driver = {
> + .probe = starfive_gpio_probe,
> + .driver = {
> + .name = "gpio_starfive_jh7100",
> + .of_match_table = of_match_ptr(starfive_gpio_match),
> + },
> +};
> +
> +static int __init starfive_gpio_init(void)
> +{
> + return platform_driver_register(&starfive_gpio_driver);
> +}
> +subsys_initcall(starfive_gpio_init);
> +
> +static void __exit starfive_gpio_exit(void)
> +{
> + platform_driver_unregister(&starfive_gpio_driver);
Do you expect GPIO driver can be removed?
The driver needs proper removal, provides .remove callback.
Example, call gpiochip_remove() , disable interrupt when removing.

> +}
> +module_exit(starfive_gpio_exit);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_AUTHOR("Huan Feng <huan.feng@starfivetech.com>");
> +MODULE_DESCRIPTION("StarFive JH7100 GPIO driver");
> --

Regards
Ley Foon

\
 
 \ /
  Last update: 2021-07-15 03:50    [W:0.936 / U:0.064 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site