lkml.org 
[lkml]   [2021]   [Jul]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH 2/2] iio: adc: Add driver for Renesas RZ/G2L A/D converter
HI Alexandru,

Thank you for the review.

On Thu, Jul 1, 2021 at 11:28 AM Alexandru Ardelean
<ardeleanalex@gmail.com> wrote:
>
> On Wed, Jun 30, 2021 at 1:07 AM Lad Prabhakar
> <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
> >
> > Add ADC driver support for Renesas RZ/G2L A/D converter in SW
> > trigger mode.
> >
> > A/D Converter block is a successive approximation analog-to-digital
> > converter with a 12-bit accuracy and supports a maximum of 8 input
> > channels.
>
> Hey,
>
> Some comments inline.
>
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> > ---
> > MAINTAINERS | 8 +
> > drivers/iio/adc/Kconfig | 10 +
> > drivers/iio/adc/Makefile | 1 +
> > drivers/iio/adc/rzg2l_adc.c | 489 ++++++++++++++++++++++++++++++++++++
> > 4 files changed, 508 insertions(+)
> > create mode 100644 drivers/iio/adc/rzg2l_adc.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 81e1edeceae4..bee4c3847e01 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -15622,6 +15622,14 @@ L: linux-renesas-soc@vger.kernel.org
> > S: Maintained
> > F: drivers/phy/renesas/phy-rcar-gen3-usb*.c
> >
> > +RENESAS RZ/G2L A/D DRIVER
> > +M: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > +L: linux-iio@vger.kernel.org
> > +L: linux-renesas-soc@vger.kernel.org
> > +S: Supported
> > +F: Documentation/devicetree/bindings/iio/adc/renesas,rzg2l-adc.yaml
> > +F: drivers/iio/adc/rzg2l_adc.c
> > +
> > RESET CONTROLLER FRAMEWORK
> > M: Philipp Zabel <p.zabel@pengutronix.de>
> > S: Maintained
> > diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> > index c7946c439612..9408cbf97acc 100644
> > --- a/drivers/iio/adc/Kconfig
> > +++ b/drivers/iio/adc/Kconfig
> > @@ -887,6 +887,16 @@ config ROCKCHIP_SARADC
> > To compile this driver as a module, choose M here: the
> > module will be called rockchip_saradc.
> >
> > +config RZG2L_ADC
> > + tristate "Renesas RZ/G2L ADC driver"
> > + depends on ARCH_R9A07G044 || COMPILE_TEST
> > + help
> > + Say yes here to build support for the ADC found in Renesas
> > + RZ/G2L family.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called rzg2l_adc.
> > +
> > config SC27XX_ADC
> > tristate "Spreadtrum SC27xx series PMICs ADC"
> > depends on MFD_SC27XX_PMIC || COMPILE_TEST
> > diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> > index a226657d19c0..d92bcc9c5fbb 100644
> > --- a/drivers/iio/adc/Makefile
> > +++ b/drivers/iio/adc/Makefile
> > @@ -82,6 +82,7 @@ obj-$(CONFIG_QCOM_PM8XXX_XOADC) += qcom-pm8xxx-xoadc.o
> > obj-$(CONFIG_RCAR_GYRO_ADC) += rcar-gyroadc.o
> > obj-$(CONFIG_RN5T618_ADC) += rn5t618-adc.o
> > obj-$(CONFIG_ROCKCHIP_SARADC) += rockchip_saradc.o
> > +obj-$(CONFIG_RZG2L_ADC) += rzg2l_adc.o
> > obj-$(CONFIG_SC27XX_ADC) += sc27xx_adc.o
> > obj-$(CONFIG_SPEAR_ADC) += spear_adc.o
> > obj-$(CONFIG_STX104) += stx104.o
> > diff --git a/drivers/iio/adc/rzg2l_adc.c b/drivers/iio/adc/rzg2l_adc.c
> > new file mode 100644
> > index 000000000000..1c58eb8ae1ec
> > --- /dev/null
> > +++ b/drivers/iio/adc/rzg2l_adc.c
> > @@ -0,0 +1,489 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * RZ/G2L A/D Converter driver
> > + *
> > + * Copyright (c) 2021 Renesas Electronics Europe GmbH
> > + *
> > + * Author: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/completion.h>
> > +#include <linux/delay.h>
> > +#include <linux/iio/iio.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/reset.h>
> > +
> > +#define ADM(n) ((n) * 0x4)
> > +#define ADM0_ADCE BIT(0)
> > +#define ADM0_ADBSY BIT(1)
> > +#define ADM0_PWDWNB BIT(2)
> > +#define ADM0_SRESB BIT(15)
> > +#define ADM1_TRG BIT(0)
> > +#define ADM1_MS BIT(2)
> > +#define ADM1_BS BIT(4)
> > +#define ADM1_EGA_CLEAR ~GENMASK(13, 12)
> > +#define ADM2_CHSEL_CLEAR ~GENMASK(7, 0)
> > +#define ADM3_ADSMP 0x578
> > +#define ADM3_ADCMP (0xe << 16)
> > +#define ADM3_ADIL_CLEAR ~GENMASK(31, 24)
> > +
> > +#define ADINT 0x20
> > +#define ADINT_CH_CLEAR ~GENMASK(7, 0)
> > +#define ADINT_CSEEN BIT(16)
> > +#define ADINT_INTS BIT(31)
> > +#define ADSTS 0x24
> > +#define ADINT_INTST_MASK GENMASK(7, 0)
> > +#define ADSTS_CSEST BIT(16)
> > +#define ADIVC 0x28
> > +#define ADIVC_DIVADC_CLEAR ~GENMASK(8, 0)
> > +#define ADIVC_DIVADC_4 0x4
> > +#define ADFIL 0x2c
> > +#define ADCR(n) (0x30 + ((n) * 0x4))
> > +#define ADCR_AD_MASK GENMASK(11, 0)
> > +
> > +#define ADC_MAX_CHANNELS 8
> > +#define ADC_CHN_MASK 0x7
> > +#define ADC_TIMEOUT usecs_to_jiffies(1 * 4)
> > +
> > +enum trigger_mode {
> > + SW_TRIGGER = 0,
> > + SYNC_TRIGGER,
> > + ASYNC_TRIGGER,
> > +};
>
> this enum could also be removed [for now] given that only SW_TRIGGER
> is supported;
>
OK will do.

> > +
> > +struct rzg2l_adc_data {
> > + const struct iio_chan_spec *channels;
> > + u8 num_channels;
> > + u8 trigger;
> > +};
> > +
> > +struct rzg2l_adc {
> > + void __iomem *base;
> > + struct clk *pclk;
> > + struct clk *adclk;
> > + struct reset_control *presetn;
> > + struct reset_control *adrstn;
> > + struct completion completion;
> > + const struct rzg2l_adc_data *data;
> > + bool adc_disabled; /* protected with mlock mutex from indio_dev */
>
> this adc_disabled flag looks a bit weird;
> it seems to guard against this driver being removed to prevent some reads.
> technically, this should be protected by IIO core;
> so the flag itself (or how it is being used) looks like it doesn't do much;
>
Agreed will drop that.

> > + u16 last_val[ADC_MAX_CHANNELS];
> > +};
> > +
> > +static unsigned int rzg2l_adc_readl(struct rzg2l_adc *adc, u32 reg)
> > +{
> > + return readl(adc->base + reg);
> > +}
> > +
> > +static void rzg2l_adc_writel(struct rzg2l_adc *adc, unsigned int reg, u32 val)
> > +{
> > + writel(val, adc->base + reg);
> > +}
> > +
> > +static int rzg2l_adc_adclk(struct rzg2l_adc *adc, bool prepare)
> > +{
> > + if (prepare)
> > + return clk_prepare_enable(adc->adclk);
> > +
> > + clk_disable_unprepare(adc->adclk);
> > + return 0;
> > +}
> > +
> > +static void rzg2l_adc_pwr(struct rzg2l_adc *adc, bool on)
> > +{
> > + u32 reg;
> > +
> > + reg = rzg2l_adc_readl(adc, ADM(0));
> > + if (on)
> > + reg |= ADM0_PWDWNB;
> > + else
> > + reg &= ~ADM0_PWDWNB;
> > + rzg2l_adc_writel(adc, ADM(0), reg);
> > + udelay(2);
> > +}
> > +
> > +static void rzg2l_adc_conversion(struct rzg2l_adc *adc, bool start)
> > +{
> > + int timeout = 5;
> > + u32 reg;
> > +
> > + /* stop A/D conversion */
> > + reg = rzg2l_adc_readl(adc, ADM(0));
> > + if (start)
> > + reg |= ADM0_ADCE;
> > + else
> > + reg &= ~ADM0_ADCE;
> > + rzg2l_adc_writel(adc, ADM(0), reg);
> > +
> > + if (start)
> > + return;
> > +
> > + do {
> > + usleep_range(100, 200);
> > + reg = rzg2l_adc_readl(adc, ADM(0));
> > + timeout--;
> > + if (!timeout) {
> > + pr_err("%s stopping ADC timed out\n", __func__);
> > + break;
> > + }
> > + } while (((reg & ADM0_ADBSY) || (reg & ADM0_ADCE)));
> > +}
> > +
> > +static int rzg2l_adc_read_raw(struct iio_dev *indio_dev,
> > + struct iio_chan_spec const *chan,
> > + int *val, int *val2, long mask)
> > +{
> > + struct rzg2l_adc *adc = iio_priv(indio_dev);
> > + u32 reg;
> > + int ret;
> > + u8 ch;
> > +
> > + switch (mask) {
> > + case IIO_CHAN_INFO_RAW:
> > + mutex_lock(&indio_dev->mlock);
>
> [1]
> acquiring indio_dev->mlock directly is discouraged;
> this lock is reserved for IIO core logic and will be moved into an
> iio_dev_opaque struct eventually;
> driver state locks should be defined in struct rzg2l_adc and managed
> by the driver to protect it's own internal state;
>
Agreed will add driver state lock in struct rzg2l_adc
>
> > +
> > + if (adc->adc_disabled) {
> > + mutex_unlock(&indio_dev->mlock);
> > + return -EBUSY;
> > + }
> > +
> > + if (rzg2l_adc_readl(adc, ADM(0)) & ADM0_ADBSY) {
> > + mutex_unlock(&indio_dev->mlock);
> > + return -EBUSY;
> > + }
> > +
> > + ch = chan->channel & ADC_CHN_MASK;
> > + /* SW trigger */
> > + reg = rzg2l_adc_readl(adc, ADM(1));
> > + reg &= ADM1_EGA_CLEAR;
> > + reg &= ~ADM1_BS;
> > + reg |= ADM1_MS;
> > + reg &= ~ADM1_TRG;
> > + rzg2l_adc_writel(adc, ADM(1), reg);
> > +
> > + /* select channel */
> > + reg = rzg2l_adc_readl(adc, ADM(2));
> > + reg &= ADM2_CHSEL_CLEAR;
> > + reg |= BIT(ch);
> > + rzg2l_adc_writel(adc, ADM(2), reg);
> > +
> > + reg = rzg2l_adc_readl(adc, ADM(3));
> > + reg &= ADM3_ADIL_CLEAR;
> > + reg |= ADM3_ADCMP;
> > + reg |= ADM3_ADSMP;
> > + rzg2l_adc_writel(adc, ADM(3), reg);
> > +
> > + reg = rzg2l_adc_readl(adc, ADIVC);
> > + reg &= ADIVC_DIVADC_CLEAR;
> > + reg |= ADIVC_DIVADC_4;
> > + rzg2l_adc_writel(adc, ADIVC, reg);
> > +
> > + reg = rzg2l_adc_readl(adc, ADINT);
> > + reg &= ~ADINT_INTS;
> > + reg &= ADINT_CH_CLEAR;
> > + reg |= ADINT_CSEEN;
> > + reg |= BIT(ch);
> > + rzg2l_adc_writel(adc, ADINT, reg);
> > +
> > + rzg2l_adc_pwr(adc, true);
>
> should all this clock & power management be done in this read function?
> it looks like an awful lot just to perform a single read
> maybe some PM suspend/resume hooks would be a better idea for these;
>
Agreed that would make the code much cleaner.

> > +
> > + ret = rzg2l_adc_adclk(adc, true);
> > + if (ret) {
> > + rzg2l_adc_pwr(adc, false);
> > + mutex_unlock(&indio_dev->mlock);
> > + return -EINVAL;
> > + }
> > +
> > + reinit_completion(&adc->completion);
> > +
> > + rzg2l_adc_conversion(adc, true);
> > +
> > + if (!wait_for_completion_timeout(&adc->completion, ADC_TIMEOUT)) {
> > + reg &= ADINT_CH_CLEAR;
> > + rzg2l_adc_writel(adc, ADINT, reg);
> > + rzg2l_adc_conversion(adc, false);
> > + rzg2l_adc_adclk(adc, false);
> > + rzg2l_adc_pwr(adc, false);
> > + mutex_unlock(&indio_dev->mlock);
> > + return -ETIMEDOUT;
> > + }
> > +
> > + *val = adc->last_val[ch];
> > + rzg2l_adc_conversion(adc, false);
> > + rzg2l_adc_adclk(adc, false);
> > + rzg2l_adc_pwr(adc, false);
> > + mutex_unlock(&indio_dev->mlock);
> > + return IIO_VAL_INT;
> > +
> > + default:
> > + return -EINVAL;
> > + }
> > +}
> > +
> > +static irqreturn_t rzg2l_adc_isr(int irq, void *dev_id)
> > +{
> > + struct rzg2l_adc *adc = (struct rzg2l_adc *)dev_id;
> > + u8 intst;
> > + u32 reg;
> > + u8 i;
> > +
> > + reg = rzg2l_adc_readl(adc, ADSTS);
> > + if (reg & ADSTS_CSEST) {
> > + rzg2l_adc_writel(adc, ADSTS, reg);
> > + return IRQ_HANDLED;
> > + }
> > +
> > + intst = reg & ADINT_INTST_MASK;
> > + if (!intst)
> > + return IRQ_HANDLED;
> > +
> > + for (i = 0; i < ADC_MAX_CHANNELS; i++) {
> > + if (intst & BIT(i))
> > + adc->last_val[i] = rzg2l_adc_readl(adc, ADCR(i)) & ADCR_AD_MASK;
> > + }
> > +
> > + rzg2l_adc_writel(adc, ADSTS, reg);
> > +
> > + complete(&adc->completion);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static const struct iio_info rzg2l_adc_iio_info = {
> > + .read_raw = rzg2l_adc_read_raw,
> > +};
> > +
> > +static const char * const rzg2l_adc_channel_name[] = {
> > + "adc0",
> > + "adc1",
> > + "adc2",
> > + "adc3",
> > + "adc4",
> > + "adc5",
> > + "adc6",
> > + "adc7",
> > +};
> > +
> > +static int rzg2l_adc_parse_of(struct platform_device *pdev, struct rzg2l_adc *adc)
> > +{
> > + struct device_node *node = pdev->dev.of_node;
> > + struct iio_chan_spec *chan_array;
> > + u8 channels[ADC_MAX_CHANNELS];
> > + struct rzg2l_adc_data *data;
> > + int num_channels;
> > + int ret;
> > + u8 i;
> > +
> > + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> > + if (!data)
> > + return -ENOMEM;
> > +
> > + num_channels = of_property_count_u8_elems(node, "renesas-rzg2l,adc-channels");
> > + if (num_channels <= 0 || num_channels > ADC_MAX_CHANNELS)
> > + return -EINVAL;
> > +
> > + ret = of_property_read_u8_array(node, "renesas-rzg2l,adc-channels",
> > + channels, num_channels);
> > + if (ret)
> > + return ret;
> > +
> > + chan_array = devm_kcalloc(&pdev->dev, num_channels, sizeof(*chan_array),
> > + GFP_KERNEL);
> > + if (!chan_array)
> > + return -ENOMEM;
> > +
> > + for (i = 0; i < num_channels; i++) {
> > + chan_array[i].type = IIO_VOLTAGE;
> > + chan_array[i].indexed = 1;
> > + chan_array[i].channel = channels[i];
> > + chan_array[i].info_mask_separate = BIT(IIO_CHAN_INFO_RAW);
> > + chan_array[i].info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE);
> > + chan_array[i].datasheet_name = rzg2l_adc_channel_name[i];
> > + }
> > +
> > + ret = of_property_read_u8(node, "renesas-rzg2l,adc-trigger-mode",
> > + &data->trigger);
> > + if (ret)
> > + data->trigger = SW_TRIGGER;
> > +
> > + /* we support SW_TRIGGER as of now */
> > + if (data->trigger != SW_TRIGGER)
> > + return -EINVAL;
>
> it would be an idea to remove this data->trigger field and the DT read
> for this property and add it when it's supported;
> typically these triggers don't get configured via DT;
>
Agreed will drop this.

> > +
> > + data->num_channels = num_channels;
> > + data->channels = chan_array;
> > + adc->data = data;
> > +
> > + return 0;
> > +}
> > +
> > +static int rzg2l_adc_sw_reset(struct rzg2l_adc *adc)
> > +{
> > + int timeout = 5;
> > + u32 val;
> > +
> > + val = rzg2l_adc_readl(adc, ADM(0));
> > + val |= ADM0_SRESB;
> > + rzg2l_adc_writel(adc, ADM(0), val);
> > +
> > + while (!(rzg2l_adc_readl(adc, ADM(0)) & ADM0_SRESB)) {
> > + if (!timeout)
> > + return -EINVAL;
>
> maybe -EBUSY is a bit better error code;
>
> > + timeout--;
> > + usleep_range(100, 200);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int rzg2l_adc_probe(struct platform_device *pdev)
> > +{
> > + struct iio_dev *indio_dev;
> > + struct rzg2l_adc *adc;
> > + int ret;
> > + int irq;
> > +
> > + indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*adc));
> > + if (!indio_dev) {
> > + dev_err(&pdev->dev, "failed allocating iio device\n");
>
> this message can be removed;
> looks like log spam;
> and if it happens, the system will be in a pretty bad state anyway
>
OK will drop this.

> > + return -ENOMEM;
> > + }
> > +
> > + adc = iio_priv(indio_dev);
> > + if (!adc)
> > + return -ENOMEM;
>
> this check is redundant;
> if indio_dev is non-NULL then iio_priv() will be good as well;
>
> > +
> > + ret = rzg2l_adc_parse_of(pdev, adc);
> > + if (ret)
> > + return -ENOMEM;
> > +
> > + adc->base = devm_platform_ioremap_resource(pdev, 0);
> > + if (IS_ERR(adc->base)) {
> > + dev_err(&pdev->dev, "missing mem resource");
>
> this message can be removed;
> looks like log-spam
>
Will drop.

> > + return PTR_ERR(adc->base);
> > + }
> > +
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq < 0) {
> > + dev_err(&pdev->dev, "no irq resource\n");
> > + return irq;
> > + }
> > +
> > + adc->pclk = devm_clk_get(&pdev->dev, "pclk");
> > + if (IS_ERR(adc->pclk)) {
> > + dev_err(&pdev->dev, "Failed to get pclk");
> > + return PTR_ERR(adc->pclk);
> > + }
> > +
> > + adc->adclk = devm_clk_get(&pdev->dev, "adclk");
> > + if (IS_ERR(adc->adclk)) {
> > + dev_err(&pdev->dev, "Failed to get adclk");
> > + return PTR_ERR(adc->adclk);
> > + }
> > +
> > + adc->adrstn = devm_reset_control_get_exclusive(&pdev->dev, "adrst-n");
> > + if (IS_ERR(adc->adrstn)) {
> > + dev_err(&pdev->dev, "failed to get adrstn\n");
> > + return PTR_ERR(adc->adrstn);
> > + }
> > +
> > + adc->presetn = devm_reset_control_get_exclusive(&pdev->dev, "presetn");
> > + if (IS_ERR(adc->presetn)) {
> > + dev_err(&pdev->dev, "failed to get presetn\n");
> > + return PTR_ERR(adc->presetn);
> > + }
> > +
> > + ret = reset_control_deassert(adc->adrstn);
> > + if (ret)
> > + return ret;
> > +
> > + ret = reset_control_deassert(adc->presetn);
> > + if (ret)
> > + goto assert_adrstn;
> > +
> > + ret = clk_prepare_enable(adc->pclk);
> > + if (ret)
> > + goto assert_presetn;
> > +
> > + ret = rzg2l_adc_sw_reset(adc);
> > + if (ret)
> > + goto unprepare_pclk;
> > +
> > + init_completion(&adc->completion);
> > +
> > + platform_set_drvdata(pdev, indio_dev);
> > +
> > + ret = devm_request_irq(&pdev->dev, irq, rzg2l_adc_isr,
> > + 0, dev_name(&pdev->dev), adc);
> > + if (ret < 0)
> > + goto unprepare_pclk;
> > +
> > + adc->adc_disabled = false;
> > + indio_dev->name = dev_name(&pdev->dev);
>
> indio_dev->name should be the part-name;
> since this driver supports a single part, this can be:
>
> indio_dev->name = "rzg2l-adc";
>
OK

> > + indio_dev->dev.parent = &pdev->dev;
> > + indio_dev->dev.of_node = pdev->dev.of_node;
>
>
> The 2 assignments above can be removed in the mainline driver.
> They should be done in devm_iio_device_alloc() and iio_device_register()
>
Agreed will drop this.

>
> > + indio_dev->info = &rzg2l_adc_iio_info;
> > + indio_dev->modes = INDIO_DIRECT_MODE;
> > + indio_dev->channels = adc->data->channels;
> > + indio_dev->num_channels = adc->data->num_channels;
> > +
> > + ret = iio_device_register(indio_dev);
> > + if (ret)
> > + goto unprepare_pclk;
> > +
> > + return 0;
> > +
> > +unprepare_pclk:
> > + clk_disable_unprepare(adc->pclk);
> > +assert_presetn:
> > + reset_control_assert(adc->presetn);
> > +assert_adrstn:
> > + reset_control_assert(adc->adrstn);
> > + return ret;
> > +}
> > +
> > +static int rzg2l_adc_remove(struct platform_device *pdev)
> > +{
> > + struct iio_dev *indio_dev = platform_get_drvdata(pdev);
> > + struct rzg2l_adc *adc = iio_priv(indio_dev);
> > +
> > + mutex_lock(&indio_dev->mlock);
> > + adc->adc_disabled = true;
> > + mutex_unlock(&indio_dev->mlock);
> > +
> > + iio_device_unregister(indio_dev);
> > +
> > + clk_disable_unprepare(adc->pclk);
> > + reset_control_assert(adc->presetn);
> > + reset_control_assert(adc->adrstn);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id rzg2l_adc_match[] = {
> > + {
> > + .compatible = "renesas,rzg2l-adc",
> > + },
> > + {},
>
> comma can be removed;
> since this is a null terminator
>
OK.

Cheers,
Prabhakar

> > +};
> > +MODULE_DEVICE_TABLE(of, rzg2l_adc_match);
> > +
> > +static struct platform_driver rzg2l_adc_driver = {
> > + .probe = rzg2l_adc_probe,
> > + .remove = rzg2l_adc_remove,
> > + .driver = {
> > + .name = "rzg2l-adc",
> > + .of_match_table = rzg2l_adc_match,
> > + },
> > +};
> > +
> > +module_platform_driver(rzg2l_adc_driver);
> > +
> > +MODULE_AUTHOR("Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>");
> > +MODULE_DESCRIPTION("Renesas RZ/G2L ADC driver");
> > +MODULE_LICENSE("GPL v2");
> > --
> > 2.17.1
> >

\
 
 \ /
  Last update: 2021-07-14 23:27    [W:0.078 / U:0.188 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site