lkml.org 
[lkml]   [2021]   [Jul]   [12]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v3 1/8] firmware: arm_scmi: Add configurable polling mode for transports
Date
SCMI communications along TX channels can optionally be provided of a
completion interrupt; when such interrupt is not available, command
transactions should rely on polling, where the SCMI core takes care to
repeatedly evaluates the transport-specific .poll_done() function to
determine if a request was completed or timed out.

Such mechanism is already present and working on a single transfer base:
SCMI protocols can indeed enable hdr.poll_completion on specific commands
ahead of each transfer and cause that transaction to be handled with
polling.

Introduce a couple of flags to be able to enforce such polling behaviour
globally at will:

- scmi_desc.force_polling: to statically switch the whole transport to
polling mode.

- scmi_chan_info.needs_polling: to switch a single channel dynamically to
polling mode if at runtime is determined
that no completion interrupt was available
for such channel.

Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
---
drivers/firmware/arm_scmi/common.h | 10 ++++++++++
drivers/firmware/arm_scmi/driver.c | 17 +++++++++++++++++
2 files changed, 27 insertions(+)

diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
index 877236b99602..2b5fa351d89f 100644
--- a/drivers/firmware/arm_scmi/common.h
+++ b/drivers/firmware/arm_scmi/common.h
@@ -320,11 +320,18 @@ void scmi_protocol_release(const struct scmi_handle *handle, u8 protocol_id);
* @dev: Reference to device in the SCMI hierarchy corresponding to this
* channel
* @handle: Pointer to SCMI entity handle
+ * @needs_polling: Flag to indicate that this channel has no completion
+ * interrupt mechanism, so it needs SCMI core to poll, using
+ * .poll_done(), to determine when a command has completed.
+ * This can be dynamically set by transports at run-time inside
+ * their provided .chan_setup() when they determine no
+ * completion interrupt is available.
* @transport_info: Transport layer related information
*/
struct scmi_chan_info {
struct device *dev;
struct scmi_handle *handle;
+ bool needs_polling;
void *transport_info;
};

@@ -383,6 +390,8 @@ struct scmi_device *scmi_child_dev_find(struct device *parent,
* be pending simultaneously in the system. May be overridden by the
* get_max_msg op.
* @max_msg_size: Maximum size of data per message that can be handled.
+ * @force_polling: Flag to force this whole transport to use SCMI core polling
+ * mechanism instead of completion interrupts even if available.
*/
struct scmi_desc {
int (*init)(void);
@@ -391,6 +400,7 @@ struct scmi_desc {
int max_rx_timeout_ms;
int max_msg;
int max_msg_size;
+ bool force_polling;
};

#ifdef CONFIG_ARM_SCMI_TRANSPORT_MAILBOX
diff --git a/drivers/firmware/arm_scmi/driver.c b/drivers/firmware/arm_scmi/driver.c
index 650da2ef59bf..36cb7a12d72f 100644
--- a/drivers/firmware/arm_scmi/driver.c
+++ b/drivers/firmware/arm_scmi/driver.c
@@ -651,6 +651,15 @@ static void scmi_handle_response(struct scmi_chan_info *cinfo,

scmi_xfer_state_update(xfer);

+ /* Discard unexpected messages when polling is active. */
+ if (xfer->hdr.type != MSG_TYPE_DELAYED_RESP &&
+ xfer->hdr.poll_completion) {
+ WARN_ON_ONCE(1);
+ dev_dbg(cinfo->dev,
+ "Completion IRQ received but using polling. Ignore.\n");
+ return;
+ }
+
/* rx.len could be shrunk in the sync do_xfer, so reset to maxsz */
if (xfer->hdr.type == MSG_TYPE_DELAYED_RESP)
xfer->rx.len = info->desc->max_msg_size;
@@ -767,6 +776,9 @@ static int do_xfer(const struct scmi_protocol_handle *ph,
if (unlikely(!cinfo))
return -EINVAL;

+ if (info->desc->force_polling || cinfo->needs_polling)
+ xfer->hdr.poll_completion = true;
+
trace_scmi_xfer_begin(xfer->transfer_id, xfer->hdr.id,
xfer->hdr.protocol_id, xfer->hdr.seq,
xfer->hdr.poll_completion);
@@ -1490,6 +1502,11 @@ static int scmi_chan_setup(struct scmi_info *info, struct device *dev,
if (ret)
return ret;

+ if (tx && (cinfo->needs_polling || info->desc->force_polling))
+ dev_info(dev,
+ "Enabled polling mode for TX channel - prot_id:%d\n",
+ prot_id);
+
idr_alloc:
ret = idr_alloc(idr, cinfo, prot_id, prot_id + 1, GFP_KERNEL);
if (ret != prot_id) {
--
2.17.1
\
 
 \ /
  Last update: 2021-07-12 18:27    [W:0.347 / U:0.200 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site