lkml.org 
[lkml]   [2021]   [Jun]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] mmc: dw_mmc: Fix hang on data CRC error
From
Date
Dear Vincent,

On 6/30/21 7:22 PM, Vincent Whitchurch wrote:
> When a Data CRC interrupt is received, the driver disables the DMA, then
> sends the stop/abort command and then waits for Data Transfer Over.
>
> However, sometimes, when a data CRC error is received in the middle of a
> multi-block write transfer, the Data Transfer Over interrupt is never
> received, and the driver hangs and never completes the request.
>
> The driver sets the BMOD.SWR bit (SDMMC_IDMAC_SWRESET) when stopping the
> DMA, but according to the manual CMD.STOP_ABORT_CMD should be programmed
> "before assertion of SWR". Do these operations in the recommended
> order. With this change the Data Transfer Over is always received
> correctly in my tests.

I will check with your patch. I didn't see any CRC error on my targets before.

Best Regards,
Jaehoon Chung

>
> Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
> ---
> drivers/mmc/host/dw_mmc.c | 6 +++---
> 1 file changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
> index f85271f5c4fa..845b0745ea37 100644
> --- a/drivers/mmc/host/dw_mmc.c
> +++ b/drivers/mmc/host/dw_mmc.c
> @@ -2083,8 +2083,8 @@ static void dw_mci_tasklet_func(struct tasklet_struct *t)
> continue;
> }
>
> - dw_mci_stop_dma(host);
> send_stop_abort(host, data);
> + dw_mci_stop_dma(host);
> state = STATE_SENDING_STOP;
> break;
> }
> @@ -2108,10 +2108,10 @@ static void dw_mci_tasklet_func(struct tasklet_struct *t)
> */
> if (test_and_clear_bit(EVENT_DATA_ERROR,
> &host->pending_events)) {
> - dw_mci_stop_dma(host);
> if (!(host->data_status & (SDMMC_INT_DRTO |
> SDMMC_INT_EBE)))
> send_stop_abort(host, data);
> + dw_mci_stop_dma(host);
> state = STATE_DATA_ERROR;
> break;
> }
> @@ -2144,10 +2144,10 @@ static void dw_mci_tasklet_func(struct tasklet_struct *t)
> */
> if (test_and_clear_bit(EVENT_DATA_ERROR,
> &host->pending_events)) {
> - dw_mci_stop_dma(host);
> if (!(host->data_status & (SDMMC_INT_DRTO |
> SDMMC_INT_EBE)))
> send_stop_abort(host, data);
> + dw_mci_stop_dma(host);
> state = STATE_DATA_ERROR;
> break;
> }
>

\
 
 \ /
  Last update: 2021-07-01 00:07    [W:0.103 / U:0.252 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site