lkml.org 
[lkml]   [2021]   [Jun]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH v2] ARM: dts: stm32: add a new DCMI pins group
The Seeed Odyssey-STM32MP157C board has a 20-pin DVP camera output.
stm32mp15-pinctrl.dtsi contained one pin state definition for the DCMI
interface, dcmi-0, AKA phandle dcmi_pins_a. This definition was
incompatible with the pins used on the Odyssey board, where:
- there are 8 data pins instead of 12,
- DCMI_HSYNC is available at PA4 instead of PH8,
- DCMI_D0 is at PC6 instead of PH9,
- DCMI_D3 is at PE1 instead of PH12,
- DCMI_D4 is at PE11 instead of PH14,
- DCMI_D5 is at PD3 instead of PI4,
- DCMI_D6 is at PE13 instead of PB8,
- DCMI_D7 is at PB9 instead of PE6.

Add the DCMI pins used on the Odyssey board as a new DCMI pin state
definition, dcmi-1, AKA phandle dcmi_pins_b.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
---
V1 -> V2: Removed the pinctrl override from the Odyssey device tree,
added a new pinctrl in stm32mp15-pinctrl.dtsi instead

arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 33 ++++++++++++++++++++++++
1 file changed, 33 insertions(+)

diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 060baa8b7e9d..5b60ecbd718f 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -118,6 +118,39 @@ pins {
};
};

+ dcmi_pins_b: dcmi-1 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 4, AF13)>,/* DCMI_HSYNC */
+ <STM32_PINMUX('B', 7, AF13)>,/* DCMI_VSYNC */
+ <STM32_PINMUX('A', 6, AF13)>,/* DCMI_PIXCLK */
+ <STM32_PINMUX('C', 6, AF13)>,/* DCMI_D0 */
+ <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+ <STM32_PINMUX('H', 11, AF13)>,/* DCMI_D2 */
+ <STM32_PINMUX('E', 1, AF13)>,/* DCMI_D3 */
+ <STM32_PINMUX('E', 11, AF13)>,/* DCMI_D4 */
+ <STM32_PINMUX('D', 3, AF13)>,/* DCMI_D5 */
+ <STM32_PINMUX('E', 13, AF13)>,/* DCMI_D6 */
+ <STM32_PINMUX('B', 9, AF13)>;/* DCMI_D7 */
+ bias-disable;
+ };
+ };
+
+ dcmi_sleep_pins_b: dcmi-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 4, ANALOG)>,/* DCMI_HSYNC */
+ <STM32_PINMUX('B', 7, ANALOG)>,/* DCMI_VSYNC */
+ <STM32_PINMUX('A', 6, ANALOG)>,/* DCMI_PIXCLK */
+ <STM32_PINMUX('C', 6, ANALOG)>,/* DCMI_D0 */
+ <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+ <STM32_PINMUX('H', 11, ANALOG)>,/* DCMI_D2 */
+ <STM32_PINMUX('E', 1, ANALOG)>,/* DCMI_D3 */
+ <STM32_PINMUX('E', 11, ANALOG)>,/* DCMI_D4 */
+ <STM32_PINMUX('D', 3, ANALOG)>,/* DCMI_D5 */
+ <STM32_PINMUX('E', 13, ANALOG)>,/* DCMI_D6 */
+ <STM32_PINMUX('B', 9, ANALOG)>;/* DCMI_D7 */
+ };
+ };
+
ethernet0_rgmii_pins_a: rgmii-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
--
2.30.2
\
 
 \ /
  Last update: 2021-06-03 17:35    [W:0.075 / U:1.352 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site