lkml.org 
[lkml]   [2021]   [Jun]   [25]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v3 4/4] MIPS: CI20: Add second percpu timer for SMP.
Hi Paul,

于 Fri, 25 Jun 2021 12:31:17 +0100
Paul Cercueil <paul@crapouillou.net> 写道:

> Hi Zhou,
>
> Le jeu., juin 24 2021 at 23:06:29 +0800, 周琰杰 (Zhou Yanjie)
> <zhouyanjie@wanyeetech.com> a écrit :
> > 1.Add a new TCU channel as the percpu timer of core1, this is to
> > prepare for the subsequent SMP support. The newly added channel
> > will not adversely affect the current single-core state.
> > 2.Adjust the position of TCU node to make it consistent with the
> > order in jz4780.dtsi file.
>
> That's a bit superfluous, the order matters when adding new nodes,
> but once they are added, moving them around only cause annoyance.
>
> >
> > Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
> > ---
> >
> > Notes:
> > v2:
> > New patch.
> >
> > v2->v3:
> > No change.
> >
> > arch/mips/boot/dts/ingenic/ci20.dts | 21 +++++++++++----------
> > 1 file changed, 11 insertions(+), 10 deletions(-)
> >
> > diff --git a/arch/mips/boot/dts/ingenic/ci20.dts
> > b/arch/mips/boot/dts/ingenic/ci20.dts
> > index 8877c62..70005cc 100644
> > --- a/arch/mips/boot/dts/ingenic/ci20.dts
> > +++ b/arch/mips/boot/dts/ingenic/ci20.dts
> > @@ -118,6 +118,17 @@
> > assigned-clock-rates = <48000000>;
> > };
> >
> > +&tcu {
> > + /*
> > + * 750 kHz for the system timers and 3 MHz for the
> > clocksources,
> > + * use channel #0 and #1 for the per cpu system timers,
> > and use
> > + * channel #2 for the clocksource.
> > + */
> > + assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu
> > TCU_CLK_TIMER1>,
> > + <&tcu TCU_CLK_TIMER2>,
> > <&tcu TCU_CLK_OST>;
> > + assigned-clock-rates = <750000>, <750000>, <3000000>,
> > <3000000>;
>
> Ideally you'd set TIMER1 to 3 MHz and TIMER2 to 750 kHz, otherwise it
> kind of breaks support for older kernels (they would still boot, but
> with a very slow clocksource). So in the new DTS you could use the
> timer0 clock for CPU #0, timer1 for the clocksource, and timer2+ for
> cpus > 0.

I checked the ingenic-timer driver, and it seems that the last TCU
channel is always used as the clocksource in the driver, so it seems
that we can only use timer2 as the clocksource in smp mode. Maybe we
should add a note for smp is closed in the comment. And I found that I
missed a problem, Nikolaus Schaller once reported that because the
frequency of the tcu timer (only 16bit) used to provide the clocksource
is too high, there will be a chance that the system will get stuck
before the clocksource is switched to ost. And reducing the clocksource
to 750kz can prevent it from happening. I will add this part to v4.
When this part is added, both clockevent and clocksource will be
750kHz, but the 750kHz clocksource is only temporary, because it will
then switch to the clocksource provided by ost, and ost works at 3MHz.

Thanks and best regards!

>
> Cheers,
> -Paul
>
> > +};
> > +
> > &mmc0 {
> > status = "okay";
> >
> > @@ -522,13 +533,3 @@
> > bias-disable;
> > };
> > };
> > -
> > -&tcu {
> > - /*
> > - * 750 kHz for the system timer and 3 MHz for the
> > clocksource,
> > - * use channel #0 for the system timer, #1 for the
> > clocksource.
> > - */
> > - assigned-clocks = <&tcu TCU_CLK_TIMER0>, <&tcu
> > TCU_CLK_TIMER1>,
> > - <&tcu TCU_CLK_OST>;
> > - assigned-clock-rates = <750000>, <3000000>, <3000000>;
> > -};
> > --
> > 2.7.4
> >
>

\
 
 \ /
  Last update: 2021-06-25 17:20    [W:0.455 / U:2.292 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site