lkml.org 
[lkml]   [2021]   [Jun]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v7 4/8] PCI/sysfs: Allow userspace to query and set device reset mechanism
On Tue, Jun 22, 2021 at 01:03:07AM +0530, Amey Narkhede wrote:
> On 21/06/21 02:07PM, Bjorn Helgaas wrote:
> > On Mon, Jun 21, 2021 at 10:58:54PM +0530, Amey Narkhede wrote:
> > > On 21/06/21 08:01AM, Bjorn Helgaas wrote:
> > > > On Sat, Jun 19, 2021 at 07:29:20PM +0530, Amey Narkhede wrote:
> > > > > On 21/06/18 03:00PM, Bjorn Helgaas wrote:
> > > > > > On Tue, Jun 08, 2021 at 11:18:53AM +0530, Amey Narkhede wrote:
> > > > > > > Add reset_method sysfs attribute to enable user to
> > > > > > > query and set user preferred device reset methods and
> > > > > > > their ordering.
> > > >
> > > > > > > + if (sysfs_streq(options, "default")) {
> > > > > > > + for (i = 0; i < PCI_RESET_METHODS_NUM; i++)
> > > > > > > + reset_methods[i] = reset_methods[i] ? prio-- : 0;
> > > > > > > + goto set_reset_methods;
> > > > > > > + }
> > > > > >
> > > > > > If you use pci_init_reset_methods() here, you can also get this case
> > > > > > out of the way early.
> > > > > >
> > > > > The problem with alternate encoding is we won't be able to know if
> > > > > one of the reset methods was disabled previously. For example,
> > > > >
> > > > > # cat reset_methods
> > > > > flr,bus # dev->reset_methods = [3, 5, 0, ...]
> > > > > # echo bus > reset_methods # dev->reset_methods = [5, 0, 0, ...]
> > > > > # cat reset_methods
> > > > > bus
> > > > >
> > > > > Now if an user wants to enable flr
> > > > >
> > > > > # echo flr > reset_methods # dev->reset_methods = [3, 0, 0, ...]
> > > > > OR
> > > > > # echo bus,flr > reset_methods # dev->reset_methods = [5, 3, 0, ...]
> > > > >
> > > > > either they need to write "default" first then flr or we will need to
> > > > > reprobe reset methods each time when user writes to reset_method attribute.
> > > >
> > > > Not sure I completely understand the problem here. I think relying on
> > > > previous state that is invisible to the user is a little problematic
> > > > because it's hard for the user to predict what will happen.
> > > >
> > > > If the user enables a method that was previously "disabled" because
> > > > the probe failed, won't the reset method itself just fail with
> > > > -ENOTTY? Is that a problem?
> > > >
> > > I think I didn't explain this correctly. With current implementation
> > > its not necessary to explicitly set *order of availabe* reset methods.
> > > User can directly write a single supported reset method only and then perform
> > > the reset. Side effect of that is other methods are disabled if user
> > > writes single or less than available number of supported reset method.
> > > Current implementation is able to handle this case but with new encoding
> > > we'll need to reprobe reset methods everytime because we have no way
> > > of distingushing supported and currently enabled reset method.
> >
> > I'm confused. I thought the point of the nested loops to find the
> > highest priority enabled reset method was to allow the user to control
> > the order. The sysfs doc says writing "reset_method" sets the "reset
> > methods and their ordering."
> >
> > It seems complicated to track "supported" and "enabled" separately,
> > and I don't know what the benefit is. If we write "reset_method" to
> > enable reset X, can we just probe reset X to see if it's supported?
>
> Although final result is same whether user writes a supported reset method or
> their ordering that is,
> # echo bus > reset_methods
> and
> # echo bus,flr > reset_methods
>
> are the same but in the first version, users don't have to explicitly
> set the ordering if they just want to perform bus reset.
> Current implementation allows the flexibility for switching between
> first and second option.

Sorry, I can't quite make sense of the above.

Your doc implies the following are different:

# echo bus,flr > reset_methods
# echo flr,bus > reset_methods

Are they? If you don't need to provide control over the order of
trying resets, this can all be simplified quite a bit.

Bjorn

\
 
 \ /
  Last update: 2021-06-23 14:06    [W:0.475 / U:0.144 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site