lkml.org 
[lkml]   [2021]   [May]   [23]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
SubjectRE: [PATCH] driver: adc: ltc2497: return directly after reading the adc conversion value
Date


> -----Original Message-----
> From: Jonathan Cameron <jic23@kernel.org>
> Sent: Saturday, May 22, 2021 1:02 AM
> To: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> Cc: Li, Meng <Meng.Li@windriver.com>; lars@metafoo.de;
> Michael.Hennerich@analog.com; pmeerw@pmeerw.net; linux-
> kernel@vger.kernel.org; linux-iio@vger.kernel.org
> Subject: Re: [PATCH] driver: adc: ltc2497: return directly after reading the adc
> conversion value
>
> [Please note: This e-mail is from an EXTERNAL e-mail address]
>
> On Wed, 19 May 2021 11:21:04 +0200
> Uwe Kleine-König <u.kleine-koenig@pengutronix.de> wrote:
>
> > On Wed, May 12, 2021 at 12:57:25PM +0800, Meng.Li@windriver.com
> wrote:
> > > From: Meng Li <Meng.Li@windriver.com>
> > >
> > > When read adc conversion value with below command:
> > > cat /sys/.../iio:device0/in_voltage0-voltage1_raw
> > > There is an error reported as below:
> > > ltc2497 0-0014: i2c transfer failed: -EREMOTEIO This i2c transfer
> > > issue is introduced by commit 69548b7c2c4f ("iio:
> > > adc: ltc2497: split protocol independent part in a separate module").
> > > When extract the common code into ltc2497-core.c, it change the code
> > > logic of function ltc2497core_read(). With wrong reading sequence,
> > > the action of enable adc channel is sent to chip again during adc
> > > channel is in conversion status. In this way, there is no ack from
> > > chip, and then cause i2c transfer failed.
> > > In order to keep the code logic is the same with original ideal, it
> > > is need to return direct after reading the adc conversion value.
> > >
> > > Fixes: 69548b7c2c4f ("iio: adc: ltc2497: split protocol independent
> > > part in a separate module ")
> > > Cc: stable@vger.kernel.org
> > > Signed-off-by: Meng Li <Meng.Li@windriver.com>
> > > ---
> > > drivers/iio/adc/ltc2497.c | 2 ++
> > > 1 file changed, 2 insertions(+)
> > >
> > > diff --git a/drivers/iio/adc/ltc2497.c b/drivers/iio/adc/ltc2497.c
> > > index 1adddf5a88a9..fd5a66860a47 100644
> > > --- a/drivers/iio/adc/ltc2497.c
> > > +++ b/drivers/iio/adc/ltc2497.c
> > > @@ -41,6 +41,8 @@ static int ltc2497_result_and_measure(struct
> ltc2497core_driverdata *ddata,
> > > }
> > >
> > > *val = (be32_to_cpu(st->buf) >> 14) - (1 << 17);
> > > +
> > > + return ret;
> >
> > This looks wrong for me. The idea of the function
> > ltc2497_result_and_measure is that it reads the result and starts a
> > new measurement. I guess the problem is that
> > ltc2497_result_and_measure is called to early, not that it does too much.
> >
> > But note I don't have such a system handy to actually debug this any
> > more.
>
> @Meng Li,
>
> I see from the datasheet that the device can be used with an external
> oscillator.
> Is that the case on your boards, because if so the timing delay of 150msecs
> may be far too short. If not, perhaps the part is right at the upper end of
> timings and we just need to add 20% to the 150msecs to be sure of not
> hitting the limit?
>

Hi Jonathan,

Thanks for your very professional comments.
I check my board schematics, the pin 35 f0 is connected to GND, so I use the internal oscillator.
In additional, I am not very understand your comment about the case of using internal oscillator.
Do you mean that you agree my patch and only need to change 150 into 180?
#define LTC2497_CONVERSION_TIME_MS 150ULL
=>
#define LTC2497_CONVERSION_TIME_MS 180ULL

Thanks,
Limeng

> Thanks,
>
> Jonathan
>
>
> >
> > Best regards
> > Uwe
> >

\
 
 \ /
  Last update: 2021-05-24 04:50    [W:0.082 / U:0.228 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site