lkml.org 
[lkml]   [2021]   [May]   [1]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
Subject[PATCH 2/2] dt-bindings: iio: adc: devicetree bindings for texas instruments ads7142 iio driver
This is a device tree schema for iio driver for
Texas Instruments ADS7142 dual-channel, programmable sensor monitor.

Datasheet: https://www.ti.com/lit/ds/symlink/ads7142.pdf

Signed-off-by: Jozsef Horvath <info@ministro.hu>
---
---
.../bindings/iio/adc/ti,ads7142.yaml | 198 ++++++++++++++++++
1 file changed, 198 insertions(+)
create mode 100644 Documentation/devicetree/bindings/iio/adc/ti,ads7142.yaml

diff --git a/Documentation/devicetree/bindings/iio/adc/ti,ads7142.yaml b/Documentation/devicetree/bindings/iio/adc/ti,ads7142.yaml
new file mode 100644
index 000000000000..b4e752160156
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/adc/ti,ads7142.yaml
@@ -0,0 +1,198 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/iio/adc/ti,ads7142.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Texas Instruments ADS7142 adc driver device tree bindings
+
+maintainers:
+ - József Horváth <info@ministro.hu>
+
+description: |
+ This document is for describing the required device tree parameters
+ for ads7142 adc driver.
+ The required parameters for proper operation are described below.
+
+ Datasheet: https://www.ti.com/lit/ds/symlink/ads7142.pdf
+
+ Operation modes supportedby the driver:
+ When the 'ti,monitoring-mode' property is not present
+ in the devicetree node definition, the driver initiates a single
+ conversion in the device for each read request
+ (/sys/bus/iio/devices/iio:deviceX/in_voltageY_raw).
+ This is a one-shot conversion, and it is called
+ "Manual Mode" in the datasheet.
+
+ When the 'ti,monitoring-mode' property is present
+ in the devicetree node definition, the driver configures
+ the device's digital window comparator and sets the device's
+ data buffer operation mode to pre alert data mode.
+ The driver reads the conversion result when the BUSY/RDY interrupt
+ fires, and keeps the value until the next BUSY/RDY interrupt
+ or the first read request
+ (/sys/bus/iio/devices/iio:deviceX/in_voltageY_raw).
+ The digital window comparator and hysteresis parameters
+ can be controlled by:
+ - the devicetree definition of channel node
+ - iio sysfs interfaces
+ This is event driven conversion, and is called
+ "Autonomous Mode with Pre Alert Data" in the datasheet.
+ This mode can be used to wake up the system with the ALERT pin,
+ in case when the monitored voltage level is out of the configured range.
+
+properties:
+ compatible:
+ const: ti,ads7142
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ description: |
+ The BUSY/PDY pin is used as interrupt line in autonomous monitoring mode.
+ maxItems: 1
+
+ vref-supply:
+ description: Regulator for the reference voltage
+
+ power-supply: true
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ "#io-channel-cells":
+ const: 1
+
+ ti,osc-sel:
+ description: |
+ If present, the driver selects the high speed oscillator.
+ See chapter 7.3.5 Oscillator and Timing Control in datasheet.
+ type: boolean
+
+ ti,n-clk:
+ description: |
+ nCLK is number of clocks in one conversion cycle.
+ See chapter 7.3.5 Oscillator and Timing Control in datasheet.
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 255
+ minimum: 0
+
+ ti,monitoring-mode:
+ description: |
+ If present, the driver selects the autonomous monitoring mode with pre alert data.
+ See chapter 7.4 Device Functional Modes in datasheet.
+ type: boolean
+
+patternProperties:
+ "^channel@[0-1]$":
+ $ref: "adc.yaml"
+ type: object
+ description: |
+ Represents the external channels which are connected to the ADC.
+ properties:
+ reg:
+ description: |
+ The channel number.
+ items:
+ minimum: 0
+ maximum: 1
+ "ti,threshold-falling":
+ description: The low threshold for channel
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 4095
+ minimum: 0
+ "ti,threshold-rising":
+ description: The high threshold for channel
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 4095
+ minimum: 0
+ "ti,hysteresis":
+ description: The hysteresis for both comparators for channel
+ $ref: /schemas/types.yaml#/definitions/uint32
+ maximum: 63
+ minimum: 0
+
+ required:
+ - reg
+
+ additionalProperties: false
+
+allOf:
+ - if:
+ required:
+ - ti,monitoring-mode
+ then:
+ required:
+ - interrupts
+
+required:
+ - compatible
+ - "#io-channel-cells"
+
+additionalProperties: false
+
+examples:
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ adc@18 {
+ compatible = "ti,ads7142";
+ reg = <0x18>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ vref-supply = <&vdd_3v3_reg>;
+ power-supply = <&vdd_1v8_reg>;
+
+ channel@0 {
+ reg = <0>;
+ };
+
+ channel@1 {
+ reg = <1>;
+ };
+ };
+ };
+ - |
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ adc@1f {
+ compatible = "ti,ads7142";
+ reg = <0x1f>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ #io-channel-cells = <1>;
+
+ vref-supply = <&vdd_3v3_reg>;
+ power-supply = <&vdd_1v8_reg>;
+
+ interrupt-parent = <&gpio>;
+ interrupts = <7 2>;
+
+ ti,monitoring-mode;
+
+ channel@0 {
+ reg = <0>;
+ ti,threshold-falling = <1000>;
+ ti,threshold-rising = <2000>;
+ ti,hysteresis = <20>;
+ };
+
+ channel@1 {
+ reg = <1>;
+ ti,threshold-falling = <100>;
+ ti,threshold-rising = <2500>;
+ ti,hysteresis = <0>;
+ };
+ };
+ };
+...
+
--
2.17.1
\
 
 \ /
  Last update: 2021-05-01 20:32    [W:0.088 / U:0.108 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site