lkml.org 
[lkml]   [2021]   [Apr]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH net v2 1/2] net: dsa: lantiq_gswip: Don't use PHY auto polling
From
Date


On 4/8/2021 11:38 AM, Martin Blumenstingl wrote:
> PHY auto polling on the GSWIP hardware can be used so link changes
> (speed, link up/down, etc.) can be detected automatically. Internally
> GSWIP reads the PHY's registers for this functionality. Based on this
> automatic detection GSWIP can also automatically re-configure it's port
> settings. Unfortunately this auto polling (and configuration) mechanism
> seems to cause various issues observed by different people on different
> devices:
> - FritzBox 7360v2: the two Gbit/s ports (connected to the two internal
> PHY11G instances) are working fine but the two Fast Ethernet ports
> (using an AR8030 RMII PHY) are completely dead (neither RX nor TX are
> received). It turns out that the AR8030 PHY sets the BMSR_ESTATEN bit
> as well as the ESTATUS_1000_TFULL and ESTATUS_1000_XFULL bits. This
> makes the PHY auto polling state machine (rightfully?) think that the
> established link speed (when the other side is Gbit/s capable) is
> 1Gbit/s.
> - None of the Ethernet ports on the Zyxel P-2812HNU-F1 (two are
> connected to the internal PHY11G GPHYs while the other three are
> external RGMII PHYs) are working. Neither RX nor TX traffic was
> observed. It is not clear which part of the PHY auto polling state-
> machine caused this.
> - FritzBox 7412 (only one LAN port which is connected to one of the
> internal GPHYs running in PHY22F / Fast Ethernet mode) was seeing
> random disconnects (link down events could be seen). Sometimes all
> traffic would stop after such disconnect. It is not clear which part
> of the PHY auto polling state-machine cauased this.
> - TP-Link TD-W9980 (two ports are connected to the internal GPHYs
> running in PHY11G / Gbit/s mode, the other two are external RGMII
> PHYs) was affected by similar issues as the FritzBox 7412 just without
> the "link down" events
>
> Switch to software based configuration instead of PHY auto polling (and
> letting the GSWIP hardware configure the ports automatically) for the
> following link parameters:
> - link up/down
> - link speed
> - full/half duplex
> - flow control (RX / TX pause)
>
> After a big round of manual testing by various people (who helped test
> this on OpenWrt) it turns out that this fixes all reported issues.
>
> Additionally it can be considered more future proof because any
> "quirk" which is implemented for a PHY on the driver side can now be
> used with the GSWIP hardware as well because Linux is in control of the
> link parameters.
>
> As a nice side-effect this also solves a problem where fixed-links were
> not supported previously because we were relying on the PHY auto polling
> mechanism, which cannot work for fixed-links as there's no PHY from
> where it can read the registers. Configuring the link settings on the
> GSWIP ports means that we now use the settings from device-tree also for
> ports with fixed-links.
>
> Fixes: 14fceff4771e51 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
> Fixes: 3e6fdeb28f4c33 ("net: dsa: lantiq_gswip: Let GSWIP automatically set the xMII clock")
> Cc: stable@vger.kernel.org
> Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>

Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
--
Florian

\
 
 \ /
  Last update: 2021-04-08 20:49    [W:0.059 / U:1.180 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site