lkml.org 
[lkml]   [2021]   [Apr]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v4 5/5] clk: ti: add am33xx/am43xx spread spectrum clock support
Hi Tero,

> Il 16/04/2021 14:43 Tero Kristo <kristo@kernel.org> ha scritto:
>
>
> Hi Dario,
>
> Spent some time looking at this, had to read through the TRM chapter of
> it also in quite detailed level to figure out how this is supposed to
> work out.
>
> Other than couple of minor nits below, the code seems ok to me. What is
> the testing that has been done with this?

The patch has been tested with laboratory instrumentation and is currently
used on a custom board based on a AM335x SOC with a TI 4.1.6 kernel. It was born
from the need to reduce the electromagnetic emissions of the display to pass the
EMI certifications. The current patch is a port of that to the mainline kernel.
The corrections to be made were minimal and not significant. I'm testing it on a
beaglebone black board, verifying with devmem that the DPLL registers are correctly
set.

>
> On 01/04/2021 22:37, Dario Binacchi wrote:
> > The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
> > As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
> > the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
> > DDR, PER, and CORE PLLs.
> >
> > Calculating the required values and setting the registers accordingly
> > was taken from the set_mpu_spreadspectrum routine contained in the
> > arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
> >
> > In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
> > SSC enabled, the reference manual explains that there is a restriction
> > of range of M values. Since the omap2_dpll_round_rate routine attempts
> > to select the minimum possible N, the value of M obtained is not
> > guaranteed to be within the range required. With the new "ti,min-div"
> > parameter it is possible to increase N and consequently M to satisfy the
> > constraint imposed by SSC.
> >
> > Signed-off-by: Dario Binacchi <dariobin@libero.it>
> >
> > ---
>
> <snip>
>
> > /* REVISIT: Set ramp-up delay? */
> > diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h
> > index c62f6fa6763d..cba093de62d8 100644
> > --- a/include/linux/clk/ti.h
> > +++ b/include/linux/clk/ti.h
> > @@ -63,6 +63,18 @@ struct clk_omap_reg {
> > * @auto_recal_bit: bitshift of the driftguard enable bit in @control_reg
> > * @recal_en_bit: bitshift of the PRM_IRQENABLE_* bit for recalibration IRQs
> > * @recal_st_bit: bitshift of the PRM_IRQSTATUS_* bit for recalibration IRQs
> > + * @ssc_deltam_reg: register containing the DPLL SSC frequency spreading
> > + * @ssc_modfreq_reg: register containing the DPLL SSC modulation frequency
> > + * @ssc_modfreq_mant_mask: mask of the mantissa component in @ssc_modfreq_reg
> > + * @ssc_modfreq_exp_mask: mask of the exponent component in @ssc_modfreq_reg
> > + * @ssc_enable_mask: mask of the DPLL SSC enable bit in @control_reg
> > + * @ssc_ack_mask: mask of the DPLL SSC turned on/off bit in @control_reg
> > + * @ssc_downspread_mask: mask of the DPLL SSC low frequency only bit in
> > + * @control_reg
> > + * @ssc_modfreq: the DPLL SSC frequency modulation in kHz
> > + * @ssc_deltam: the DPLL SSC frequency spreading in permille (10th of percent)
> > + * @ssc_downspread: require the only low frequency spread of the DPLL in SSC
> > + * mode
> > * @flags: DPLL type/features (see below)
> > *
> > * Possible values for @flags:
> > @@ -110,6 +122,18 @@ struct dpll_data {
> > u8 auto_recal_bit;
> > u8 recal_en_bit;
> > u8 recal_st_bit;
> > + struct clk_omap_reg ssc_deltam_reg;
> > + struct clk_omap_reg ssc_modfreq_reg;
> > + u32 ssc_deltam_int_mask;
> > + u32 ssc_deltam_frac_mask;
> > + u32 ssc_modfreq_mant_mask;
> > + u32 ssc_modfreq_exp_mask;
> > + u32 ssc_enable_mask;
> > + u32 ssc_ack_mask;
>
> ssc_ack_mask is not used for anything in the code.

Ok, I will remove it.

>
> > + u32 ssc_downspread_mask;
> > + u32 ssc_modfreq;
> > + u32 ssc_deltam;
> > + u8 ssc_downspread;
>
> ssc_downspread should be boolean?

Yes.

Thanks and regards,
Dario

>
> > u8 flags;
> > };
> >
> >

\
 
 \ /
  Last update: 2021-04-18 16:50    [W:0.050 / U:0.184 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site