lkml.org 
[lkml]   [2021]   [Apr]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[v6] PCI: Add reset quirk for Huawei Intelligent NIC virtual function
Date
When we do an FLR on several VFs at the same time, the Huawei
Intelligent NIC processes them serially, resulting in some VF
FLRs being delayed more than 100ms, when the virtual machine
restarts and the device driver is loaded, the firmware is doing
the corresponding VF FLR, causing the driver to fail to load.
Link: https://support.huawei.com/enterprise/en/doc/EDOC1100063073/87950645/vm-oss-occasionally-fail-to-load-the-in200-driver-when-the-vf-performs-flr

To solve this problem, add host and firmware status synchronization
during FLR.

Signed-off-by: Chiqijun <chiqijun@huawei.com>
---
v6:
- Addressed Bjorn's review comments

v5:
- Fix build warning reported by kernel test robot

v4:
- Addressed Bjorn's review comments

v3:
- The MSE bit in the VF configuration space is hardwired to zero,
remove the setting of PCI_COMMAND_MEMORY bit. Add comment for
set PCI_COMMAND register.

v2:
- Update comments
- Use the HINIC_VF_FLR_CAP_BIT_SHIFT and HINIC_VF_FLR_PROC_BIT_SHIFT
macro instead of the magic number
---
drivers/pci/quirks.c | 69 ++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 69 insertions(+)

diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c
index 653660e3ba9e..6677b7220442 100644
--- a/drivers/pci/quirks.c
+++ b/drivers/pci/quirks.c
@@ -3913,6 +3913,73 @@ static int delay_250ms_after_flr(struct pci_dev *dev, int probe)
return 0;
}

+#define PCI_DEVICE_ID_HINIC_VF 0x375E
+#define HINIC_VF_FLR_TYPE 0x1000
+#define HINIC_VF_FLR_CAP_BIT (1UL << 30)
+#define HINIC_VF_OP 0xE80
+#define HINIC_VF_FLR_PROC_BIT (1UL << 18)
+#define HINIC_OPERATION_TIMEOUT 15000 /* 15 seconds */
+
+/* Device-specific reset method for Huawei Intelligent NIC virtual functions */
+static int reset_hinic_vf_dev(struct pci_dev *pdev, int probe)
+{
+ unsigned long timeout;
+ void __iomem *bar;
+ u32 val;
+
+ if (probe)
+ return 0;
+
+ bar = pci_iomap(pdev, 0, 0);
+ if (!bar)
+ return -ENOTTY;
+
+ /* Get and check firmware capabilities. */
+ val = ioread32be(bar + HINIC_VF_FLR_TYPE);
+ if (!(val & HINIC_VF_FLR_CAP_BIT)) {
+ pci_iounmap(pdev, bar);
+ return -ENOTTY;
+ }
+
+ /*
+ * Set the processing bit for the start of FLR, which will be cleared
+ * by the firmware after FLR is completed.
+ */
+ val = ioread32be(bar + HINIC_VF_OP);
+ val = val | HINIC_VF_FLR_PROC_BIT;
+ iowrite32be(val, bar + HINIC_VF_OP);
+
+ /* Perform the actual device function reset */
+ pcie_flr(pdev);
+
+ /*
+ * The device must learn BDF after FLR in order to respond to BAR's
+ * read request, therefore, we issue a configure write request to let
+ * the device capture BDF.
+ */
+ pci_write_config_word(pdev, PCI_VENDOR_ID, 0);
+
+ /* Waiting for device reset complete */
+ timeout = jiffies + msecs_to_jiffies(HINIC_OPERATION_TIMEOUT);
+ do {
+ val = ioread32be(bar + HINIC_VF_OP);
+ if (!(val & HINIC_VF_FLR_PROC_BIT))
+ goto reset_complete;
+ msleep(20);
+ } while (time_before(jiffies, timeout));
+
+ val = ioread32be(bar + HINIC_VF_OP);
+ if (!(val & HINIC_VF_FLR_PROC_BIT))
+ goto reset_complete;
+
+ pci_warn(pdev, "Reset dev timeout, FLR ack reg: %#010x\n", val);
+
+reset_complete:
+ pci_iounmap(pdev, bar);
+
+ return 0;
+}
+
static const struct pci_dev_reset_methods pci_dev_reset_methods[] = {
{ PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF,
reset_intel_82599_sfp_virtfn },
@@ -3924,6 +3991,8 @@ static const struct pci_dev_reset_methods pci_dev_reset_methods[] = {
{ PCI_VENDOR_ID_INTEL, 0x0953, delay_250ms_after_flr },
{ PCI_VENDOR_ID_CHELSIO, PCI_ANY_ID,
reset_chelsio_generic_dev },
+ { PCI_VENDOR_ID_HUAWEI, PCI_DEVICE_ID_HINIC_VF,
+ reset_hinic_vf_dev },
{ 0 }
};

--
2.17.1
\
 
 \ /
  Last update: 2021-04-14 15:17    [W:0.075 / U:0.136 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site