lkml.org 
[lkml]   [2021]   [Apr]   [14]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Date
SubjectRe: [PATCH] USB: Don't set USB_PORT_FEAT_SUSPEND on WD19's Realtek Hub
On Tue, Apr 13, 2021 at 10:44 PM Alan Stern <stern@rowland.harvard.edu> wrote:
>
> On Tue, Apr 13, 2021 at 03:52:14PM +0800, Chris Chiu wrote:
> > On Mon, Apr 12, 2021 at 11:12 PM Alan Stern <stern@rowland.harvard.edu> wrote:
> > >
> > > On Mon, Apr 12, 2021 at 11:00:06PM +0800, chris.chiu@canonical.com wrote:
> > > > The USB_PORT_FEAT_SUSPEND is not really necessary due to the
> > > > "global suspend" in USB 2.0 spec. It's only for many hub devices
> > > > which don't relay wakeup requests from the devices connected to
> > > > downstream ports. For this realtek hub, there's no problem waking
> > > > up the system from connected keyboard.
> > >
> > > What about runtime suspend? That _does_ require USB_PORT_FEAT_SUSPEND.
> >
> > It's hard to reproduce the same thing with runtime PM. I also don't
> > know the aggressive
> > way to trigger runtime suspend. So I'm assuming the same thing will happen in
> > runtime PM case because they both go the same usb_port_resume path. Could
> > you please suggest a better way to verify this for runtime PM?
>
> To put a USB device into runtime suspend, do this:
>
> echo 0 >/sys/bus/usb/devices/.../bConfigurationValue
> echo auto >/sys/bus/usb/devices/.../power/control
>
> where ... is the pathname for the device you want to suspend. (Note
> that this will unbind the device from its driver, so make sure there's
> no possibility of data loss before you do it.)
>
> To resume the device, write "on" to the power/control file. You can
> verify the runtime-PM status by reading the files in the power/
> subdirectory.
>
Thanks for the instructions. I can hit the same timeout problem with
runtime PM. The
fail rate seems the same as normal PM. (around 1/4 ~ 1/7)
root@:/sys/bus/usb/devices/3-4.3# echo auto > power/control
root@:/sys/bus/usb/devices/3-4.3# echo on > power/control
root@:/sys/bus/usb/devices/3-4.3# dmesg -c
[ 2789.679807] usb 3-4: kworker/7:0 timed out on ep0out len=0/0
[ 2789.679812] usb 3-4-port3: can't suspend, status -110
[ 2789.680078] usb 3-4.3: Failed to suspend device, error -110


> > > > This commit bypasses the USB_PORT_FEAT_SUSPEND for the quirky hub.
> > > >
> > > > Signed-off-by: Chris Chiu <chris.chiu@canonical.com>
> > > > ---
> > >
> > >
> > > > diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
> > > > index 7f71218cc1e5..8478d49bba77 100644
> > > > --- a/drivers/usb/core/hub.c
> > > > +++ b/drivers/usb/core/hub.c
> > > > @@ -3329,8 +3329,11 @@ int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
> > > > * descendants is enabled for remote wakeup.
> > > > */
> > > > else if (PMSG_IS_AUTO(msg) || usb_wakeup_enabled_descendants(udev) > 0)
> > > > - status = set_port_feature(hub->hdev, port1,
> > > > - USB_PORT_FEAT_SUSPEND);
> > > > + if (udev->quirks & USB_QUIRK_NO_SET_FEAT_SUSPEND)
> > >
> > > You should test hub->hdev->quirks, here, not udev->quirks. The quirk
> > > belongs to the Realtek hub, not to the device that's plugged into the
> > > hub.
> > >
> >
> > Thanks for pointing that out. I'll verify again and propose a V2 after
> > it's done.
>
> Another thing to consider: You shouldn't return 0 from usb_port_suspend
> if the port wasn't actually suspended. We don't want to kernel to have
> a false idea of the hardware's current state.
>
So we still need the "really_suspend=false". What if I replace it with
the following?
It's a little verbose but expressive enough. Any suggestions?

+ else if (!(hub->hdev->quirks & USB_QUIRK_NO_SET_FEAT_SUSPEND) &&
+ (PMSG_IS_AUTO(msg) || usb_wakeup_enabled_descendants(udev) > 0))
+ status = set_port_feature(hub->hdev, port1,
+ USB_PORT_FEAT_SUSPEND);
else {
really_suspend = false;
status = 0;

Chris

> Alan Stern

\
 
 \ /
  Last update: 2021-04-14 07:09    [W:0.134 / U:1.168 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site