lkml.org 
[lkml]   [2021]   [Mar]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v1 2/4] arm64: dts: imx8mq-nitrogen: add USB HOST support
Date
Add the description for the USB host port.
At this time, the port will not work directly from the
kernel because it's connected through a resettable hub
that is not handle in the kernel. It should be controlled
in the bootloader or in the userspace.

In the case of the Boundary's u-boot, this is done on the
boot script:
"
starting USB...
Bus usb@38100000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@38200000: Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
scanning bus usb@38100000 for devices... 1 USB Device(s) found
scanning bus usb@38200000 for devices... 3 USB Device(s) found
"

Signed-off-by: Adrien Grassein <adrien.grassein@gmail.com>
---
.../boot/dts/freescale/imx8mq-nitrogen.dts | 22 +++++++++++++++++++
1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index b46f45a82be1..7a52e247c527 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -213,6 +213,22 @@ &usb3_phy0 {
status = "okay";
};

+&usb_dwc3_1 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+/*
+ * On this board, USB host is connected to a resettable hub.
+ * The reset signal is connected to the GPIO <&gpio1 14 GPIO_ACTIVE_LOW>.
+ * You need to activate it in the bootloader or in the userspace.
+ */
+&usb3_phy1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb3_1>;
+};
+
&usdhc1 {
assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>;
assigned-clock-rates = <400000000>;
@@ -388,6 +404,12 @@ MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x16
>;
};

+ pinctrl_usb3_1: usb3-1grp {
+ fsl,pins = <
+ MX8MQ_IOMUXC_GPIO1_IO14_GPIO1_IO14 0x16
+ >;
+ };
+
pinctrl_usdhc1: usdhc1grp {
fsl,pins = <
MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83
--
2.25.1
\
 
 \ /
  Last update: 2021-03-30 10:37    [W:0.507 / U:0.072 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site