lkml.org 
[lkml]   [2021]   [Mar]   [18]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
Subject[PATCH v2] scsi: libsas: Reset num_scatter if libata mark qc as NODATA
From
When the cache_type for the scsi device is changed, the scsi layer
issues a MODE_SELECT command. The caching mode details are communicated
via a request buffer associated with the scsi command with data
direction set as DMA_TO_DEVICE (scsi_mode_select). When this command
reaches the libata layer, as a part of generic initial setup, libata
layer sets up the scatterlist for the command using the scsi command
(ata_scsi_qc_new). This command is then translated by the libata layer
into ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat). The libata layer
treats this as a non data command (ata_mselect_caching), since it only
needs an ata taskfile to pass the caching on/off information to the
device. It does not need the scatterlist that has been setup, so it does
not perform dma_map_sg on the scatterlist (ata_qc_issue). Unfortunately,
when this command reaches the libsas layer(sas_ata_qc_issue), libsas
layer sees it as a non data command with a scatterlist. It cannot
extract the correct dma length, since the scatterlist has not been
mapped with dma_map_sg for a DMA operation. When this partially
constructed SAS task reaches pm80xx LLDD, it results in below warning.

"pm80xx_chip_sata_req 6058: The sg list address
start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
end_addr_low=0xffffffff has crossed 4G boundary"

This patch updates code to handle ata non data commands separately so
num_scatter and total_xfer_len remain 0.

Fixes: 53de092f47ff ("scsi: libsas: Set data_dir as DMA_NONE if libata marks qc as NODATA")
Signed-off-by: Jolly Shah <jollys@google.com>
---
v2:
- reorganized code to avoid setting num_scatter twice

drivers/scsi/libsas/sas_ata.c | 9 ++++-----
1 file changed, 4 insertions(+), 5 deletions(-)

diff --git a/drivers/scsi/libsas/sas_ata.c b/drivers/scsi/libsas/sas_ata.c
index 024e5a550759..8b9a39077dba 100644
--- a/drivers/scsi/libsas/sas_ata.c
+++ b/drivers/scsi/libsas/sas_ata.c
@@ -201,18 +201,17 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc)
memcpy(task->ata_task.atapi_packet, qc->cdb, qc->dev->cdb_len);
task->total_xfer_len = qc->nbytes;
task->num_scatter = qc->n_elem;
+ task->data_dir = qc->dma_dir;
+ } else if (qc->tf.protocol == ATA_PROT_NODATA) {
+ task->data_dir = DMA_NONE;
} else {
for_each_sg(qc->sg, sg, qc->n_elem, si)
xfer += sg_dma_len(sg);

task->total_xfer_len = xfer;
task->num_scatter = si;
- }
-
- if (qc->tf.protocol == ATA_PROT_NODATA)
- task->data_dir = DMA_NONE;
- else
task->data_dir = qc->dma_dir;
+ }
task->scatter = qc->sg;
task->ata_task.retry_count = 1;
task->task_state_flags = SAS_TASK_STATE_PENDING;
--
2.31.0.rc2.261.g7f71774620-goog
\
 
 \ /
  Last update: 2021-03-18 23:57    [W:1.606 / U:0.052 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site