lkml.org 
[lkml]   [2021]   [Mar]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCHv2 04/38] dt-bindings: power: supply: bq25890: Convert to DT schema format
Date
Convert the binding to DT schema format.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
.../bindings/power/supply/bq25890.txt | 60 ---------
.../bindings/power/supply/bq25890.yaml | 123 ++++++++++++++++++
2 files changed, 123 insertions(+), 60 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/power/supply/bq25890.txt
create mode 100644 Documentation/devicetree/bindings/power/supply/bq25890.yaml

diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt
deleted file mode 100644
index 805040c6fff9..000000000000
--- a/Documentation/devicetree/bindings/power/supply/bq25890.txt
+++ /dev/null
@@ -1,60 +0,0 @@
-Binding for TI bq25890 Li-Ion Charger
-
-This driver will support the bq25892, the bq25896 and the bq25890. There are
-other ICs in the same family but those have not been tested.
-
-Required properties:
-- compatible: Should contain one of the following:
- * "ti,bq25890"
- * "ti,bq25892"
- * "ti,bq25895"
- * "ti,bq25896"
-- reg: integer, i2c address of the device.
-- interrupts: interrupt line;
-- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV);
-- ti,charge-current: integer, maximum charging current (in uA);
-- ti,termination-current: integer, charge will be terminated when current in
- constant-voltage phase drops below this value (in uA);
-- ti,precharge-current: integer, maximum charge current during precharge
- phase (in uA);
-- ti,minimum-sys-voltage: integer, when battery is charging and it is below
- minimum system voltage, the system will be regulated above
- minimum-sys-voltage setting (in uV);
-- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
-- ti,boost-max-current: integer, maximum allowed current draw in boost mode
- (in uA).
-
-Optional properties:
-- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
- otherwise 1.5MHz;
-- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
- input current will be the lower between the resistor setting and the IINLIM
- register setting;
-- ti,thermal-regulation-threshold: integer, temperature above which the charge
- current is lowered, to avoid overheating (in degrees Celsius). If omitted,
- the default setting will be used (120 degrees);
-- ti,ibatcomp-micro-ohms: integer, value of a resistor in series with
- the battery;
-- ti,ibatcomp-clamp-microvolt: integer, maximum charging voltage adjustment due
- to expected voltage drop on in-series resistor;
-
-Example:
-
-bq25890 {
- compatible = "ti,bq25890";
- reg = <0x6a>;
-
- interrupt-parent = <&gpio1>;
- interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
-
- ti,battery-regulation-voltage = <4200000>;
- ti,charge-current = <1000000>;
- ti,termination-current = <50000>;
- ti,precharge-current = <128000>;
- ti,minimum-sys-voltage = <3600000>;
- ti,boost-voltage = <5000000>;
- ti,boost-max-current = <1000000>;
-
- ti,use-ilim-pin;
- ti,thermal-regulation-threshold = <120>;
-};
diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.yaml b/Documentation/devicetree/bindings/power/supply/bq25890.yaml
new file mode 100644
index 000000000000..bf823b615439
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq25890.yaml
@@ -0,0 +1,123 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2021 Sebastian Reichel
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/supply/bq25890.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Binding for bq25890, bq25892, bq25895 and bq25896 Li-Ion Charger
+
+maintainers:
+ - Sebastian Reichel <sre@kernel.org>
+
+allOf:
+ - $ref: power-supply.yaml#
+
+properties:
+ compatible:
+ enum:
+ - ti,bq25890
+ - ti,bq25892
+ - ti,bq25895
+ - ti,bq25896
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ ti,battery-regulation-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: maximum charging voltage (in uV)
+
+ ti,charge-current:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: maximum charging current (in uA)
+
+ ti,termination-current:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ charge will be terminated when current in constant-voltage phase
+ drops below this value (in uA)
+
+ ti,precharge-current:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: maximum charge current during precharge phase (in uA)
+
+ ti,minimum-sys-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ when battery is charging and it is below minimum system voltage,
+ the system will be regulated above minimum-sys-voltage setting (in uV)
+
+ ti,boost-voltage:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: VBUS voltage level in boost mode (in uV)
+
+ ti,boost-max-current:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: maximum allowed current draw in boost mode (in uA)
+
+ ti,boost-low-freq:
+ description: boost mode frequency will be 500kHz, otherwise 1.5MHz
+ type: boolean
+
+ ti,use-ilim-pin:
+ description: |
+ ILIM resistor will be used and the input current will be the lower
+ between the resistor setting and the IINLIM register setting
+ type: boolean
+
+ ti,thermal-regulation-threshold:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ temperature above which the charge current is lowered, to avoid overheating
+ (in degrees Celsius). If omitted, the default setting will be used (120 degrees)
+
+ ti,ibatcomp-micro-ohms:
+ description: value of a resistor in series with the battery (in Micro Ohms)
+
+ ti,ibatcomp-clamp-microvolt:
+ description: max. charging voltage adjustment due to expected voltage drop on in-series resistor
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - ti,battery-regulation-voltage
+ - ti,charge-current
+ - ti,termination-current
+ - ti,precharge-current
+ - ti,minimum-sys-voltage
+ - ti,boost-voltage
+ - ti,boost-max-current
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+ i2c0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ charger@6a {
+ compatible = "ti,bq25890";
+ reg = <0x6a>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <16 IRQ_TYPE_EDGE_FALLING>;
+
+ ti,battery-regulation-voltage = <4200000>;
+ ti,charge-current = <1000000>;
+ ti,termination-current = <50000>;
+ ti,precharge-current = <128000>;
+ ti,minimum-sys-voltage = <3600000>;
+ ti,boost-voltage = <5000000>;
+ ti,boost-max-current = <1000000>;
+
+ ti,use-ilim-pin;
+ ti,thermal-regulation-threshold = <120>;
+ };
+ };
--
2.30.2
\
 
 \ /
  Last update: 2021-03-17 14:51    [W:0.316 / U:0.128 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site