lkml.org 
[lkml]   [2021]   [Mar]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v7 25/38] iio/scmi: port driver to the new scmi_sensor_proto_ops interface
Hi Christian,

Thanks for the detailed explanation. Sounds good to me.

Thanks,
Jyoti

On Tue, Mar 16, 2021 at 3:22 PM Cristian Marussi
<cristian.marussi@arm.com> wrote:
>
> Hi Jyoti,
>
> On Tue, Mar 16, 2021 at 10:51:48AM -0700, Jyoti Bhayana wrote:
> > Hi Christian,
> >
> > Thanks for porting this driver to the new interface. I have two questions:
> >
> > 1) In the following code snippet, can the sensor_ops be made as part
> > of struct scmi_iio_priv as scmi_protocol_handle is also part of that
> > struct. Not sure if there are any particular reasons for having the
> > protocol handle as part of the struct but the sensor_ops as global?
> >
> > > +static const struct scmi_sensor_proto_ops *sensor_ops;
> > >+
> > >.struct scmi_iio_priv {
> > >- struct scmi_handle *handle;
> > >+ struct scmi_protocol_handle *ph;
> > > const struct scmi_sensor_info *sensor_info;
> > > struct iio_dev *indio_dev;
> >
>
> So, the protocol_handle represents a reference to an instance of
> the sensor protocol initialized against the specific SCMI platform
> instance referred by the handle provided in the probe: so that if you
> should have multiple SCMI platforms defined in the DT, this driver
> (as all SCMI drivers) would be probed multiple times each time with a
> different handle and it would obtain a different protocol_handle each
> time it issued a probe() => devm_protocol_get().
> For this reason the obtained protocol_handle cannot be kept as a global
> and it seemed a good fit to stay in the existent scmi_iio_priv.
>
> On the other side, the sensor_ops are just plain function pointers (as
> they were before), so on any possible probe they are returned the same
> (for the same proto): it is indeed the specified protocol_handle used
> at invocation time that determines against which instance they actually
> operates (if multiple instances present at all); so the sensor_ops seemed
> a good fit for a global, also because that way tehy are more easily
> accessible throughout the driver.
>
> Does it make sense ?
>
> > 2) Looks like the event notifier registration is SCMI device managed
> > and that's why there is no call to unregister. I am assuming that you
> > have tested the logic of inserting the module, removing it and then
> > again inserting it to make sure that when the event is registered a
> > second time , the logic is all good.
> >
> > > ret = handle->notify_ops->devm_event_notifier_register(sdev,
> >
>
> Sure, I tested load/unload in general for also other SCMI drivers just
> to be sure not to have broken completely the world with this series.
>
> Please find below a load/unload/load sequence for scmi_iio.ko.
> (there are 2 emulated sensors, only one is timestamped)
>
> Thanks
>
> Cristian
>
> ---
>
> (debian-arm64)root@debarm64:~# ls /sys/bus/iio/devices/
> (debian-arm64)root@debarm64:~# insmod ./scmi_iio.ko
> (debian-arm64)root@debarm64:~# ls /sys/bus/iio/devices/
> iio:device0 iio:device1
> (debian-arm64)root@debarm64:~# cat /sys/bus/iio/devices/iio\:device0/name
> emu8_accel
> (debian-arm64)root@debarm64:~# cat /sys/bus/iio/devices/iio\:device1/name
> emu9_gyro
> (debian-arm64)root@debarm64:~# /root/iio_generic_buffer -a -c -1 -g -l 100 -N 0
> iio device number being used is 0
> trigger-less mode selected
> Enabling all channels
> Enabling: in_accel_x_en
> Enabling: in_accel_z_en
> Enabling: in_timestamp_en
> Enabling: in_accel_y_en
> -7737 -7729 -7721 16725578467193651200.000000
> -7736 -7728 -7720 16725578467193651200.000000
> -7735 -7727 -7719 16725578467193651200.000000
> -7734 -7726 -7718 16725578467193651200.000000
> -7733 -7725 -7717 16725578467193651200.000000
> -7732 -7724 -7716 16725578467193651200.000000
> -7731 -7723 -7715 16725578467193651200.000000
> -7730 -7722 -7714 17725578795097784320.000000
> -7729 -7721 -7713 17725578795097784320.000000
> -7728 -7720 -7712 17725578795097784320.000000
> -7727 -7719 -7711 17725578795097784320.000000
> -7726 -7718 -7710 17725578795097784320.000000
> -7725 -7717 -7709 17725578795097784320.000000
> -7724 -7716 -7708 17725578795097784320.000000
> -7723 -7715 -7707 17725578795097784320.000000
> -7722 -7714 -7706 17725578795097784320.000000
> -7721 -7713 -7705 17725578795097784320.000000
> ^CCaught signal 2
> Disabling: in_accel_x_en
> Disabling: in_accel_z_en
> Disabling: in_timestamp_en
> Disabling: in_accel_y_en
> (debian-arm64)root@debarm64:~# /root/iio_generic_buffer -a -c -1 -g -l 100 -N 1
> iio device number being used is 1
> trigger-less mode selected
> Enabling all channels
> Enabling: in_accel_x_en
> Enabling: in_accel_z_en
> Enabling: in_timestamp_en
> Enabling: in_accel_y_en
> -3583 -3574 -3565 270679244800.000000
> -3582 -3573 -3564 270780203008.000000
> -3581 -3572 -3563 270880358400.000000
> -3580 -3571 -3562 270980431872.000000
> -3579 -3570 -3561 271080521728.000000
> -3578 -3569 -3560 271180611584.000000
> -3577 -3568 -3559 271280685056.000000
> -3576 -3567 -3558 271380774912.000000
> -3575 -3566 -3557 271480848384.000000
> -3574 -3565 -3556 271580938240.000000
> -3573 -3564 -3555 271681028096.000000
> -3572 -3563 -3554 271781101568.000000
> -3571 -3562 -3553 271881191424.000000
> -3570 -3561 -3552 271981264896.000000
> -3569 -3560 -3551 272081354752.000000
> ^CCaught signal 2
> Disabling: in_accel_x_en
> Disabling: in_accel_z_en
> Disabling: in_timestamp_en
> Disabling: in_accel_y_en
> (debian-arm64)root@debarm64:~#
> (debian-arm64)root@debarm64:~# rmmod ./scmi_iio.ko
> (debian-arm64)root@debarm64:~# ls /sys/bus/iio/devices/
> (debian-arm64)root@debarm64:~# insmod ./scmi_iio.ko
> (debian-arm64)root@debarm64:~# ls /sys/bus/iio/devices/
> iio:device0 iio:device1
> (debian-arm64)root@debarm64:~# /root/iio_generic_buffer -a -c -1 -g -l 100 -N 0
> iio device number being used is 0
> trigger-less mode selected
> Enabling all channels
> Enabling: in_accel_x_en
> Enabling: in_accel_z_en
> Enabling: in_timestamp_en
> Enabling: in_accel_y_en
> -7308 -7300 -7292 4385346052291559424.000000
> -7307 -7299 -7291 4385346052291559424.000000
> -7306 -7298 -7290 4385346052291559424.000000
> -7305 -7297 -7289 4385346052291559424.000000
> -7304 -7296 -7288 4385346052291559424.000000
> -7303 -7295 -7287 4385346052291559424.000000
> -7302 -7294 -7286 4385346052291559424.000000
> -7301 -7293 -7285 5385346380195692544.000000
> -7300 -7292 -7284 5385346380195692544.000000
> -7299 -7291 -7283 5385346380195692544.000000
> -7298 -7290 -7282 5385346380195692544.000000
> -7297 -7289 -7281 5385346380195692544.000000
> -7296 -7288 -7280 5385346380195692544.000000
> ^CCaught signal 2
> Disabling: in_accel_x_en
> Disabling: in_accel_z_en
> Disabling: in_timestamp_en
> Disabling: in_accel_y_en
> (debian-arm64)root@debarm64:~# /root/iio_generic_buffer -a -c -1 -g -l 100 -N 1
> iio device number being used is 1
> trigger-less mode selected
> Enabling all channels
> Enabling: in_accel_x_en
> Enabling: in_accel_z_en
> Enabling: in_timestamp_en
> Enabling: in_accel_y_en
> -3161 -3152 -3143 312944197632.000000
> -3160 -3151 -3142 313044303872.000000
> -3159 -3150 -3141 313144377344.000000
> -3158 -3149 -3140 313244483584.000000
> -3157 -3148 -3139 313344851968.000000
> -3156 -3147 -3138 313445023744.000000
> -3155 -3146 -3137 313545097216.000000
> -3154 -3145 -3136 313645465600.000000
> -3153 -3144 -3135 313745604608.000000
> -3152 -3143 -3134 313845710848.000000
> -3151 -3142 -3133 313945784320.000000
> -3150 -3141 -3132 314045890560.000000
> -3149 -3140 -3131 314145964032.000000
> -3148 -3139 -3130 314246070272.000000
> -3147 -3138 -3129 314346143744.000000
> -3146 -3137 -3128 314446249984.000000
> -3145 -3136 -3127 314546618368.000000
> -3144 -3135 -3126 314647052288.000000
> ^CCaught signal 2
> Disabling: in_accel_x_en
> Disabling: in_accel_z_en
> Disabling: in_timestamp_en
> Disabling: in_accel_y_en
>
> > Thanks,
> > Jyoti
> >
> > On Tue, Mar 16, 2021 at 5:50 AM Cristian Marussi
> > <cristian.marussi@arm.com> wrote:
> > >
> > > Port driver to the new SCMI Sensor interface based on protocol handles
> > > and common devm_get_ops().
> > >
> > > Cc: Jyoti Bhayana <jbhayana@google.com>
> > > Cc: Jonathan Cameron <jic23@kernel.org>
> > > Signed-off-by: Cristian Marussi <cristian.marussi@arm.com>
> > > ---
> > > drivers/iio/common/scmi_sensors/scmi_iio.c | 91 ++++++++++------------
> > > 1 file changed, 41 insertions(+), 50 deletions(-)
> > >
> > > diff --git a/drivers/iio/common/scmi_sensors/scmi_iio.c b/drivers/iio/common/scmi_sensors/scmi_iio.c
> > > index 872d87ca6256..b4bdc3f3a946 100644
> > > --- a/drivers/iio/common/scmi_sensors/scmi_iio.c
> > > +++ b/drivers/iio/common/scmi_sensors/scmi_iio.c
> > > @@ -21,8 +21,10 @@
> > >
> > > #define SCMI_IIO_NUM_OF_AXIS 3
> > >
> > > +static const struct scmi_sensor_proto_ops *sensor_ops;
> > > +
> > > struct scmi_iio_priv {
> > > - struct scmi_handle *handle;
> > > + struct scmi_protocol_handle *ph;
> > > const struct scmi_sensor_info *sensor_info;
> > > struct iio_dev *indio_dev;
> > > /* adding one additional channel for timestamp */
> > > @@ -82,7 +84,6 @@ static int scmi_iio_sensor_update_cb(struct notifier_block *nb,
> > > static int scmi_iio_buffer_preenable(struct iio_dev *iio_dev)
> > > {
> > > struct scmi_iio_priv *sensor = iio_priv(iio_dev);
> > > - u32 sensor_id = sensor->sensor_info->id;
> > > u32 sensor_config = 0;
> > > int err;
> > >
> > > @@ -92,27 +93,11 @@ static int scmi_iio_buffer_preenable(struct iio_dev *iio_dev)
> > >
> > > sensor_config |= FIELD_PREP(SCMI_SENS_CFG_SENSOR_ENABLED_MASK,
> > > SCMI_SENS_CFG_SENSOR_ENABLE);
> > > -
> > > - err = sensor->handle->notify_ops->register_event_notifier(sensor->handle,
> > > - SCMI_PROTOCOL_SENSOR, SCMI_EVENT_SENSOR_UPDATE,
> > > - &sensor_id, &sensor->sensor_update_nb);
> > > - if (err) {
> > > - dev_err(&iio_dev->dev,
> > > - "Error in registering sensor update notifier for sensor %s err %d",
> > > - sensor->sensor_info->name, err);
> > > - return err;
> > > - }
> > > -
> > > - err = sensor->handle->sensor_ops->config_set(sensor->handle,
> > > - sensor->sensor_info->id, sensor_config);
> > > - if (err) {
> > > - sensor->handle->notify_ops->unregister_event_notifier(sensor->handle,
> > > - SCMI_PROTOCOL_SENSOR,
> > > - SCMI_EVENT_SENSOR_UPDATE, &sensor_id,
> > > - &sensor->sensor_update_nb);
> > > + err = sensor_ops->config_set(sensor->ph, sensor->sensor_info->id,
> > > + sensor_config);
> > > + if (err)
> > > dev_err(&iio_dev->dev, "Error in enabling sensor %s err %d",
> > > sensor->sensor_info->name, err);
> > > - }
> > >
> > > return err;
> > > }
> > > @@ -120,25 +105,13 @@ static int scmi_iio_buffer_preenable(struct iio_dev *iio_dev)
> > > static int scmi_iio_buffer_postdisable(struct iio_dev *iio_dev)
> > > {
> > > struct scmi_iio_priv *sensor = iio_priv(iio_dev);
> > > - u32 sensor_id = sensor->sensor_info->id;
> > > u32 sensor_config = 0;
> > > int err;
> > >
> > > sensor_config |= FIELD_PREP(SCMI_SENS_CFG_SENSOR_ENABLED_MASK,
> > > SCMI_SENS_CFG_SENSOR_DISABLE);
> > > -
> > > - err = sensor->handle->notify_ops->unregister_event_notifier(sensor->handle,
> > > - SCMI_PROTOCOL_SENSOR, SCMI_EVENT_SENSOR_UPDATE,
> > > - &sensor_id, &sensor->sensor_update_nb);
> > > - if (err) {
> > > - dev_err(&iio_dev->dev,
> > > - "Error in unregistering sensor update notifier for sensor %s err %d",
> > > - sensor->sensor_info->name, err);
> > > - return err;
> > > - }
> > > -
> > > - err = sensor->handle->sensor_ops->config_set(sensor->handle, sensor_id,
> > > - sensor_config);
> > > + err = sensor_ops->config_set(sensor->ph, sensor->sensor_info->id,
> > > + sensor_config);
> > > if (err) {
> > > dev_err(&iio_dev->dev,
> > > "Error in disabling sensor %s with err %d",
> > > @@ -161,8 +134,8 @@ static int scmi_iio_set_odr_val(struct iio_dev *iio_dev, int val, int val2)
> > > u32 sensor_config;
> > > char buf[32];
> > >
> > > - int err = sensor->handle->sensor_ops->config_get(sensor->handle,
> > > - sensor->sensor_info->id, &sensor_config);
> > > + int err = sensor_ops->config_get(sensor->ph, sensor->sensor_info->id,
> > > + &sensor_config);
> > > if (err) {
> > > dev_err(&iio_dev->dev,
> > > "Error in getting sensor config for sensor %s err %d",
> > > @@ -208,8 +181,8 @@ static int scmi_iio_set_odr_val(struct iio_dev *iio_dev, int val, int val2)
> > > sensor_config |=
> > > FIELD_PREP(SCMI_SENS_CFG_ROUND_MASK, SCMI_SENS_CFG_ROUND_AUTO);
> > >
> > > - err = sensor->handle->sensor_ops->config_set(sensor->handle,
> > > - sensor->sensor_info->id, sensor_config);
> > > + err = sensor_ops->config_set(sensor->ph, sensor->sensor_info->id,
> > > + sensor_config);
> > > if (err)
> > > dev_err(&iio_dev->dev,
> > > "Error in setting sensor update interval for sensor %s value %u err %d",
> > > @@ -274,8 +247,8 @@ static int scmi_iio_get_odr_val(struct iio_dev *iio_dev, int *val, int *val2)
> > > u32 sensor_config;
> > > int mult;
> > >
> > > - int err = sensor->handle->sensor_ops->config_get(sensor->handle,
> > > - sensor->sensor_info->id, &sensor_config);
> > > + int err = sensor_ops->config_get(sensor->ph, sensor->sensor_info->id,
> > > + &sensor_config);
> > > if (err) {
> > > dev_err(&iio_dev->dev,
> > > "Error in getting sensor config for sensor %s err %d",
> > > @@ -542,15 +515,17 @@ static int scmi_iio_buffers_setup(struct iio_dev *scmi_iiodev)
> > > return 0;
> > > }
> > >
> > > -static struct iio_dev *scmi_alloc_iiodev(struct device *dev,
> > > - struct scmi_handle *handle,
> > > - const struct scmi_sensor_info *sensor_info)
> > > +static struct iio_dev *
> > > +scmi_alloc_iiodev(struct scmi_device *sdev, struct scmi_protocol_handle *ph,
> > > + const struct scmi_sensor_info *sensor_info)
> > > {
> > > struct iio_chan_spec *iio_channels;
> > > struct scmi_iio_priv *sensor;
> > > enum iio_modifier modifier;
> > > enum iio_chan_type type;
> > > struct iio_dev *iiodev;
> > > + struct device *dev = &sdev->dev;
> > > + const struct scmi_handle *handle = sdev->handle;
> > > int i, ret;
> > >
> > > iiodev = devm_iio_device_alloc(dev, sizeof(*sensor));
> > > @@ -560,7 +535,7 @@ static struct iio_dev *scmi_alloc_iiodev(struct device *dev,
> > > iiodev->modes = INDIO_DIRECT_MODE;
> > > iiodev->dev.parent = dev;
> > > sensor = iio_priv(iiodev);
> > > - sensor->handle = handle;
> > > + sensor->ph = ph;
> > > sensor->sensor_info = sensor_info;
> > > sensor->sensor_update_nb.notifier_call = scmi_iio_sensor_update_cb;
> > > sensor->indio_dev = iiodev;
> > > @@ -595,6 +570,17 @@ static struct iio_dev *scmi_alloc_iiodev(struct device *dev,
> > > sensor_info->axis[i].id);
> > > }
> > >
> > > + ret = handle->notify_ops->devm_event_notifier_register(sdev,
> > > + SCMI_PROTOCOL_SENSOR, SCMI_EVENT_SENSOR_UPDATE,
> > > + &sensor->sensor_info->id,
> > > + &sensor->sensor_update_nb);
> > > + if (ret) {
> > > + dev_err(&iiodev->dev,
> > > + "Error in registering sensor update notifier for sensor %s err %d",
> > > + sensor->sensor_info->name, ret);
> > > + return ERR_PTR(ret);
> > > + }
> > > +
> > > scmi_iio_set_timestamp_channel(&iio_channels[i], i);
> > > iiodev->channels = iio_channels;
> > > return iiodev;
> > > @@ -604,24 +590,29 @@ static int scmi_iio_dev_probe(struct scmi_device *sdev)
> > > {
> > > const struct scmi_sensor_info *sensor_info;
> > > struct scmi_handle *handle = sdev->handle;
> > > + struct scmi_protocol_handle *ph;
> > > struct device *dev = &sdev->dev;
> > > struct iio_dev *scmi_iio_dev;
> > > u16 nr_sensors;
> > > int err = -ENODEV, i;
> > >
> > > - if (!handle || !handle->sensor_ops) {
> > > + if (!handle)
> > > + return -ENODEV;
> > > +
> > > + sensor_ops = handle->devm_protocol_get(sdev, SCMI_PROTOCOL_SENSOR, &ph);
> > > + if (IS_ERR(sensor_ops)) {
> > > dev_err(dev, "SCMI device has no sensor interface\n");
> > > - return -EINVAL;
> > > + return PTR_ERR(sensor_ops);
> > > }
> > >
> > > - nr_sensors = handle->sensor_ops->count_get(handle);
> > > + nr_sensors = sensor_ops->count_get(ph);
> > > if (!nr_sensors) {
> > > dev_dbg(dev, "0 sensors found via SCMI bus\n");
> > > return -ENODEV;
> > > }
> > >
> > > for (i = 0; i < nr_sensors; i++) {
> > > - sensor_info = handle->sensor_ops->info_get(handle, i);
> > > + sensor_info = sensor_ops->info_get(ph, i);
> > > if (!sensor_info) {
> > > dev_err(dev, "SCMI sensor %d has missing info\n", i);
> > > return -EINVAL;
> > > @@ -636,7 +627,7 @@ static int scmi_iio_dev_probe(struct scmi_device *sdev)
> > > sensor_info->axis[0].type != RADIANS_SEC)
> > > continue;
> > >
> > > - scmi_iio_dev = scmi_alloc_iiodev(dev, handle, sensor_info);
> > > + scmi_iio_dev = scmi_alloc_iiodev(sdev, ph, sensor_info);
> > > if (IS_ERR(scmi_iio_dev)) {
> > > dev_err(dev,
> > > "failed to allocate IIO device for sensor %s: %ld\n",
> > > --
> > > 2.17.1
> > >

\
 
 \ /
  Last update: 2021-03-17 06:41    [W:0.186 / U:0.420 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site