lkml.org 
[lkml]   [2021]   [Mar]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 4.9 72/78] hwmon: (lm90) Fix max6658 sporadic wrong temperature reading
Date
From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

From: Boyang Yu <byu@arista.com>

commit 62456189f3292c62f87aef363f204886dc1d4b48 upstream.

max6658 may report unrealistically high temperature during
the driver initialization, for which, its overtemp alarm pin
also gets asserted. For certain devices implementing overtemp
protection based on that pin, it may further trigger a reset to
the device. By reproducing the problem, the wrong reading is
found to be coincident with changing the conversion rate.

To mitigate this issue, set the stop bit before changing the
conversion rate and unset it thereafter. After such change, the
wrong reading is not reproduced. Apply this change only to the
max6657 kind for now, controlled by flag LM90_PAUSE_ON_CONFIG.

Signed-off-by: Boyang Yu <byu@arista.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/hwmon/lm90.c | 42 ++++++++++++++++++++++++++++++++++++++----
1 file changed, 38 insertions(+), 4 deletions(-)

--- a/drivers/hwmon/lm90.c
+++ b/drivers/hwmon/lm90.c
@@ -186,6 +186,7 @@ enum chips { lm90, adm1032, lm99, lm86,
#define LM90_HAVE_EMERGENCY_ALARM (1 << 5)/* emergency alarm */
#define LM90_HAVE_TEMP3 (1 << 6) /* 3rd temperature sensor */
#define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */
+#define LM90_PAUSE_FOR_CONFIG (1 << 8) /* Pause conversion for config */

/* LM90 status */
#define LM90_STATUS_LTHRM (1 << 0) /* local THERM limit tripped */
@@ -286,6 +287,7 @@ static const struct lm90_params lm90_par
.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
},
[max6657] = {
+ .flags = LM90_PAUSE_FOR_CONFIG,
.alert_alarms = 0x7c,
.max_convrate = 8,
.reg_local_ext = MAX6657_REG_R_LOCAL_TEMPL,
@@ -486,6 +488,38 @@ static inline int lm90_select_remote_cha
return 0;
}

+static int lm90_write_convrate(struct i2c_client *client,
+ struct lm90_data *data, int val)
+{
+ int err;
+ int config_orig, config_stop;
+
+ /* Save config and pause conversion */
+ if (data->flags & LM90_PAUSE_FOR_CONFIG) {
+ config_orig = lm90_read_reg(client, LM90_REG_R_CONFIG1);
+ if (config_orig < 0)
+ return config_orig;
+ config_stop = config_orig | 0x40;
+ if (config_orig != config_stop) {
+ err = i2c_smbus_write_byte_data(client,
+ LM90_REG_W_CONFIG1,
+ config_stop);
+ if (err < 0)
+ return err;
+ }
+ }
+
+ /* Set conv rate */
+ err = i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE, val);
+
+ /* Revert change to config */
+ if (data->flags & LM90_PAUSE_FOR_CONFIG && config_orig != config_stop)
+ i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1,
+ config_orig);
+
+ return err;
+}
+
/*
* Set conversion rate.
* client->update_lock must be held when calling this function (unless we are
@@ -506,7 +540,7 @@ static int lm90_set_convrate(struct i2c_
if (interval >= update_interval * 3 / 4)
break;

- err = i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE, i);
+ err = lm90_write_convrate(client, data, i);
data->update_interval = DIV_ROUND_CLOSEST(update_interval, 64);
return err;
}
@@ -1512,8 +1546,7 @@ static void lm90_restore_conf(void *_dat
struct i2c_client *client = data->client;

/* Restore initial configuration */
- i2c_smbus_write_byte_data(client, LM90_REG_W_CONVRATE,
- data->convrate_orig);
+ lm90_write_convrate(client, data, data->convrate_orig);
i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1,
data->config_orig);
}
@@ -1530,12 +1563,13 @@ static int lm90_init_client(struct i2c_c
/*
* Start the conversions.
*/
- lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */
config = lm90_read_reg(client, LM90_REG_R_CONFIG1);
if (config < 0)
return config;
data->config_orig = config;

+ lm90_set_convrate(client, data, 500); /* 500ms; 2Hz conversion rate */
+
/* Check Temperature Range Select */
if (data->kind == adt7461 || data->kind == tmp451) {
if (config & 0x04)

\
 
 \ /
  Last update: 2021-03-15 15:01    [W:1.563 / U:0.368 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site