lkml.org 
[lkml]   [2021]   [Mar]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH] arm64: dts: sc7280: Add qspi, qupv3_0 and qupv3_1 nodes
Hi,

On Wed, Mar 10, 2021 at 7:41 PM Roja Rani Yarubandi
<rojay@codeaurora.org> wrote:
>
> +&qspi_cs0 {
> + pinconf {
> + pins = "gpio15";
> + bias-disable;
> + };

The "pinconf" / "pinmux" subnode shouldn't be used for new SoCs. See:

http://lore.kernel.org/r/CAD=FV=UY_AFRrAY0tef5jP698LEng6oN652LcX3B4nG=aWh0gA@mail.gmail.com

...same feedback for this whole patch.

> + qup_spi0_default: qup-spi0-default {
> + pinmux {
> + pins = "gpio0", "gpio1",
> + "gpio2", "gpio3";
> + function = "qup00";
> + };
> + };

Please split these SPI nodes as per the thread above, like:

tlmm: pinctrl@... {
qup_spi0_data_clk: qup-spi0-data-clk {
pins = "gpio0", "gpio1", "gpio2";
function = "qup0";
};

qup_spi0_cs: qup-spi0-cs {
pins = "gpio3";
function = "qup0";
};

qup_spi0_cs_gpio: qup-spi0-cs-gpio {
pins = "gpio3";
function = "gpio";
};
};


> + qup_uart0_default: qup-uart0-default {
> + pinmux {
> + pins = "gpio0", "gpio1",
> + "gpio2", "gpio3";
> + function = "qup00";
> + };
> + };

I suspect things would actually be cleaner if we broke the uart lines
up since the boards tend to have to adjust pulls differently for each
line. With the new "no pinconf / pinmux" world it's pretty clean. It's
obviously up to Bjorn, but if it were me I'd request this in the SoC
file:

qup_uart0_cts: qup-uart0-cts {
pins = "...";
function = "qup00";
};

qup_uart0_rts: qup-uart0-rts {
pins = "...";
function = "qup00";
};

qup_uart0_rx: qup-uart0-rx {
pins = "...";
function = "qup00";
};

qup_uart0_tx: qup-uart0-tx {
pins = "...";
function = "qup00";
};

...and now when the board file wants to adjust the pulls they can just
reference each one:

/*
* Comments about why the UART0 pulls make sense.
* Blah blah blah.
*/

&qup_uart0_cts {
bias-pull-down;
};

&qup_uart0_rts {
drive-strength = <2>;
bias-disable;
};

&qup_uart0_rx {
bias-pull-up;
};

&qup_uart0_tx {
drive-strength = <2>;
bias-disable;
};


> + qspi: spi@88dc000 {

I believe the qspi node is sorted incorrectly. When I apply this to
the top of the Qualcomm tree it shows up after the "apps_smmu:
iommu@15000000" node. However:

0x088dc000 < 0x15000000

...which means it should be _before_.

-Doug

\
 
 \ /
  Last update: 2021-03-11 22:57    [W:0.257 / U:0.204 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site