lkml.org 
[lkml]   [2021]   [Feb]   [21]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 2/2] counter: add IRQ or GPIO based event counter
On Tue, 16 Feb 2021 09:13:56 +0100
Oleksij Rempel <o.rempel@pengutronix.de> wrote:

> Add simple IRQ or GPIO base event counter. This device is used to measure
> rotation speed of some agricultural devices, so no high frequency on the
> counter pin is expected.
>
> The maximal measurement frequency depends on the CPU and system load. On
> the idle iMX6S I was able to measure up to 20kHz without count drops.
>
> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
> Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
A FYI note inline.

Driver looks good to me.

Jonathan

> ---
> MAINTAINERS | 7 +
> drivers/counter/Kconfig | 10 ++
> drivers/counter/Makefile | 1 +
> drivers/counter/interrupt-cnt.c | 249 ++++++++++++++++++++++++++++++++
> 4 files changed, 267 insertions(+)
> create mode 100644 drivers/counter/interrupt-cnt.c
>
...

> +static int interrupt_cnt_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct interrupt_cnt_priv *priv;
> + int ret;
> +
> + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->irq = platform_get_irq_optional(pdev, 0);
> + if (priv->irq == -ENXIO)
> + priv->irq = 0;
> + else if (priv->irq < 0)
> + return dev_err_probe(dev, priv->irq, "failed to get IRQ\n");
> +
> + priv->gpio = devm_gpiod_get_optional(dev, NULL, GPIOD_IN);
> + if (IS_ERR(priv->gpio))
> + return dev_err_probe(dev, PTR_ERR(priv->gpio), "failed to get GPIO\n");
> +
> + if (!priv->irq && !priv->gpio) {
> + dev_err(dev, "IRQ and GPIO are not found. At least one source should be provided\n");
> + return -ENODEV;
> + }
> +
> + if (!priv->irq) {
> + int irq = gpiod_to_irq(priv->gpio);
> +
> + if (irq < 0)
> + return dev_err_probe(dev, irq, "failed to get IRQ from GPIO\n");
> +
> + priv->irq = irq;
> + }
> +
> + priv->counter.priv = priv;
> + priv->counter.name = dev_name(dev);
> + priv->counter.parent = dev;
> + priv->counter.ops = &interrupt_cnt_ops;
> + priv->counter.counts = interrupt_cnts;
> + priv->counter.num_counts = ARRAY_SIZE(interrupt_cnts);
> + priv->counter.signals = interrupt_cnt_signals;
> + priv->counter.num_signals = priv->gpio ?
> + ARRAY_SIZE(interrupt_cnt_signals) : 0;
> +
> + irq_set_status_flags(priv->irq, IRQ_NOAUTOEN);

Just as a side note, there is a series that cleans up this case, though no
idea if it will make the merge window or not.

https://lore.kernel.org/linux-input/aefbe49321b845c98e505518314a93cc@hisilicon.com/

If it does we can tidy this up then.

> + ret = devm_request_irq(dev, priv->irq, interrupt_cnt_isr,
> + IRQF_TRIGGER_RISING | IRQF_NO_THREAD,
> + INTERRUPT_CNT_NAME, priv);
> + if (ret)
> + return ret;
> +
> + return devm_counter_register(dev, &priv->counter);
> +}
> +
...

\
 
 \ /
  Last update: 2021-02-21 16:43    [W:0.086 / U:0.168 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site