lkml.org 
[lkml]   [2021]   [Dec]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH 0/3] clk: qcom: smd-rpm: Report enable state to framework
From
Date
Quoting Stephan Gerhold (2021-11-09 02:26:21)
> Hi Shawn,
>
> On Tue, Nov 09, 2021 at 10:25:55AM +0800, Shawn Guo wrote:
> > Currently the enable state of smd-rpm clocks are not properly reported
> > back to framework due to missing .is_enabled and .is_prepared hooks.
> > This causes a couple of issues.
> >
> > - All those unused clocks are not voted for off, because framework has
> > no knowledge that they are unused. It becomes a problem for vlow
> > power mode support, as we do not have every single RPM clock claimed
> > and voted for off by client devices, and rely on clock framework to
> > disable those unused RPM clocks.
> >
>
> I posted a similar patch a bit more than a year ago [1]. Back then one
> of the concerns was that we might disable critical clocks just because
> they have no driver using it actively. For example, not all of the
> platforms using clk-smd-rpm already have an interconnect driver.
> Disabling the interconnect related clocks will almost certainly make the
> device lock up completely. (I tried it back then, it definitely does...)
>
> I proposed adding CLK_IGNORE_UNUSED for the interconnect related clocks
> back then [2] which would allow disabling most of the clocks at least.
> Stephen Boyd had an alternative proposal to instead move the
> interconnect related clocks completely out of clk-smd-rpm [3].
> But I'm still unsure how this would work in a backwards compatible way. [4]

We should stop adding to the pile of smd-rpm clks that are clearly
interconnects. I'm ready to stop accepting patches like 78b727d02815
("clk: qcom: smd-rpm: Add QCM2290 RPM clock support").

Someone needs to put in the work to make an interconnect provider that
directly talks to the rpm, without going through the clk framework just
because the rpm talks in kHz for these resources. These clk have no
parent and are essentially a proxy for some firmware interface to the
rpm but we put it behind the clk framework for reasons I don't know why.

I honestly don't understand the backwards incompatibility argument for
this either. If we're adding more SoC support for this driver we need to
stop and figure out a better approach. Make a new interconnect driver,
plug it in via DT, wait a release cycle, and finally dump the smd-rpm
clk node from older platforms that were using the clk framework. At
least for new SoCs this problem doesn't exist.

There's that one graphics clk (RPM_SMD_GFX3D_CLK_SRC) but I don't see it
used anywhere. So it's not really important? Maybe we need to set some
bandwidth in the graphics clk driver? I dunno.

>
> Since your patches are more or less identical I'm afraid the same
> concerns still need to be solved somehow. :)
>
> Thanks,
> Stephan
>
> [1]: https://lore.kernel.org/linux-arm-msm/20200817140908.185976-1-stephan@gerhold.net/
> [2]: https://lore.kernel.org/linux-arm-msm/20200818080738.GA46574@gerhold.net/
> [3]: https://lore.kernel.org/linux-arm-msm/159796605593.334488.8355244657387381953@swboyd.mtv.corp.google.com/
> [4]: https://lore.kernel.org/linux-arm-msm/20200821064857.GA905@gerhold.net/

\
 
 \ /
  Last update: 2021-12-09 10:11    [W:0.258 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site