lkml.org 
[lkml]   [2021]   [Dec]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v4 7/7] arm64: dts: exynos: Add initial device tree support for Exynos7885 SoC
On Wed, 8 Dec 2021 at 11:05, Krzysztof Kozlowski
<krzysztof.kozlowski@canonical.com> wrote:
>
> On 07/12/2021 21:19, Sam Protsenko wrote:
> > On Mon, 6 Dec 2021 at 17:32, David Virag <virag.david003@gmail.com> wrote:
> >>
> >> Add initial Exynos7885 device tree nodes with dts for the Samsung Galaxy
> >> A8 (2018), a.k.a. "jackpotlte", with model number "SM-A530F".
> >> Currently this includes some clock support, UART support, and I2C nodes.
> >>
> >> Signed-off-by: David Virag <virag.david003@gmail.com>
> >> ---
> >> Changes in v2:
> >> - Remove address-cells, and size-cells from dts, since they are
> >> already in the dtsi.
> >> - Lower case hex in memory node
> >> - Fix node names with underscore instead of hyphen
> >> - Fix line breaks
> >> - Fix "-key" missing from gpio keys node names
> >> - Use the form without "key" in gpio key labels on all keys
> >> - Suffix pin configuration node names with "-pins"
> >> - Remove "fimc_is_mclk" nodes from pinctrl dtsi for now
> >> - Use macros for "samsung,pin-con-pdn", and "samsung,pin-con-pdn"
> >> - Add comment about Arm PMU
> >> - Rename "clock-oscclk" to "osc-clock"
> >> - Include exynos-syscon-restart.dtsi instead of rewriting its contents
> >>
> >> Changes in v3:
> >> - Fix typo (seperate -> separate)
> >>
> >> Changes in v4:
> >> - Fixed leading 0x in clock-controller nodes
> >> - Actually suffixed pin configuration node names with "-pins"
> >> - Seperated Cortex-A53 and Cortex-A73 PMU
> >>
> >> arch/arm64/boot/dts/exynos/Makefile | 7 +-
> >> .../boot/dts/exynos/exynos7885-jackpotlte.dts | 95 ++
> >> .../boot/dts/exynos/exynos7885-pinctrl.dtsi | 865 ++++++++++++++++++
> >> arch/arm64/boot/dts/exynos/exynos7885.dtsi | 438 +++++++++
> >> 4 files changed, 1402 insertions(+), 3 deletions(-)
> >> create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
> >
> > Shouldn't SoC and board files be sent as two separate patches? For
> > example, I've checked exynos5433 and exynos7, SoC support
>
> Does not have to be. DTSI by itself cannot be even compiled, so keeping
> it a separate commit does not bring that much benefits. Especially if it
> is only one DTSI and one DTS.
>

Right, the only theoretical benefit I can see is reverting the board
dts in future, if another board already uses SoC dtsi. Or
cherry-picking in similar manner. Not my call though, for me it just
seems easier to review it that way, and more atomic.

> >
> >> create mode 100644 arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
> >> create mode 100644 arch/arm64/boot/dts/exynos/exynos7885.dtsi
> >>
> >> diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile
> >> index b41e86df0a84..c68c4ad577ac 100644
> >> --- a/arch/arm64/boot/dts/exynos/Makefile
> >> +++ b/arch/arm64/boot/dts/exynos/Makefile
> >> @@ -1,6 +1,7 @@
> >> # SPDX-License-Identifier: GPL-2.0
> >> dtb-$(CONFIG_ARCH_EXYNOS) += \
> >> - exynos5433-tm2.dtb \
> >> - exynos5433-tm2e.dtb \
> >> - exynos7-espresso.dtb \
> >> + exynos5433-tm2.dtb \
> >> + exynos5433-tm2e.dtb \
> >> + exynos7-espresso.dtb \
> >> + exynos7885-jackpotlte.dtb \
> >> exynosautov9-sadk.dtb
> >> diff --git a/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts b/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
> >> new file mode 100644
> >> index 000000000000..f5941dc4c374
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
> >> @@ -0,0 +1,95 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Samsung Galaxy A8 2018 (jackpotlte/SM-A530F) device tree source
> >> + *
> >> + * Copyright (c) 2021 Samsung Electronics Co., Ltd.
> >> + * Copyright (c) 2021 Dávid Virág
> >> + *
> >
> > This line is not needed.
> >
> >> + */
> >> +
> >> +/dts-v1/;
> >
> > Suggest adding empty line here.
> >
> >> +#include "exynos7885.dtsi"
> >> +#include <dt-bindings/gpio/gpio.h>
> >> +#include <dt-bindings/input/input.h>
> >> +#include <dt-bindings/interrupt-controller/irq.h>
> >> +
> >> +/ {
> >> + model = "Samsung Galaxy A8 (2018)";
> >> + compatible = "samsung,jackpotlte", "samsung,exynos7885";
> >> + chassis-type = "handset";
> >> +
> >> + aliases {
> >> + serial0 = &serial_0;
> >> + serial1 = &serial_1;
> >> + serial2 = &serial_2;
> >
> > Suggestion: add aliases also for i2c nodes, to keep i2c instance
> > numbers fixed in run-time (e.g. in "i2cdetect -l" output).
> >
> >> + };
> >> +
> >> + chosen {
> >> + stdout-path = &serial_2;
> >> + };
> >> +
> >> + memory@80000000 {
> >> + device_type = "memory";
> >> + reg = <0x0 0x80000000 0x3da00000>,
> >> + <0x0 0xc0000000 0x40000000>,
> >> + <0x8 0x80000000 0x40000000>;
> >> + };
> >> +
> >> + gpio-keys {
> >> + compatible = "gpio-keys";
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&key_volup &key_voldown &key_power>;
> >> +
> >> + volup-key {
> >> + label = "Volume Up";
> >> + interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>;
> >
> > Here and below: what is 0, why it's needed? Also, isn't it enough to
> > have just "gpios", and remove interrupt*? Need to check "gpio-keys"
> > driver and bindings doc, but AFAIR it should be enough to have just
> > "gpios =" or just "interrupts =".
>
> "gpios" is enough, because the IRQ line is derived from it. However
> explicitly describing interrupts seems like a more detailed hardware
> description.
>

Frankly I don't think it's more detailed, it states the same thing
(gpa1 controller, line=5). Also not sure if level interrupt is needed
for a key, maybe edge type would be better. Also, I still don't
understand 0 in the end. Checking existing dts's, most of those only
define "gpios". I'd say having only "gpios" is more obvious, and will
work the same way. But that's not a strong preference on my side, just
think it's a bit misleading right now.

> >
> >
> >> + interrupt-parent = <&gpa1>;
> >> + linux,code = <KEY_VOLUMEUP>;
> >> + gpios = <&gpa1 5 GPIO_ACTIVE_LOW>;
> >> + };
> >> +
> >> + voldown-key {
> >> + label = "Volume Down";
> >> + interrupts = <6 IRQ_TYPE_LEVEL_HIGH 0>;
> >> + interrupt-parent = <&gpa1>;
> >> + linux,code = <KEY_VOLUMEDOWN>;
> >> + gpios = <&gpa1 6 GPIO_ACTIVE_LOW>;
> >> + };
> >> +
> >> + power-key {
> >> + label = "Power";
> >> + interrupts = <7 IRQ_TYPE_LEVEL_HIGH 0>;
> >> + interrupt-parent = <&gpa1>;
> >> + linux,code = <KEY_POWER>;
> >> + gpios = <&gpa1 7 GPIO_ACTIVE_LOW>;
> >> + wakeup-source;
> >> + };
> >> + };
> >> +};
> >> +
> >
> > If there are some LEDs by chance on that board -- it might be useful
> > to define those here with "gpio-leds" as well. Maybe even set some
> > default trigger like "heartbeat".
> >
> >> +&serial_2 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&pinctrl_alive {
> >> + key_volup: key-volup-pins {
> >> + samsung,pins = "gpa1-5";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
> >
> > Maybe EXYNOS_PIN_FUNC_EINT is more self-explanatory? Just a suggestion though.
> >
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >
> > Here and below: please use EXYNOS5420_PIN_DRV_LV1 (means drive level = 1x).
>
> But are these drive level 1x? The Exynos Auto v9 has different values
> than older ones.
>

It should be that. One way to implicitly figure that out is to look at
nodes like "sd0_clk_fast_slew_rate_3x" and those pin-drv properties.
Also, in Exynos850 for most of domains those constants are
appropriate, that's why I mentioned that.

> >
> >> + };
> >> +
> >> + key_voldown: key-voldown-pins {
> >> + samsung,pins = "gpa1-6";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + key_power: key-power-pins {
> >> + samsung,pins = "gpa1-7";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +};
> >> diff --git a/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
> >> new file mode 100644
> >> index 000000000000..8336b2e48858
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
> >> @@ -0,0 +1,865 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Samsung Exynos7885 SoC pin-mux and pin-config device tree source
> >> + *
> >> + * Copyright (c) 2017 Samsung Electronics Co., Ltd.
> >> + * Copyright (c) 2021 Dávid Virág
> >> + *
> >> + * Samsung's Exynos7885 SoC pin-mux and pin-config options are listed as
> >> + * device tree nodes in this file.
> >> + */
> >> +
> >> +#include <dt-bindings/pinctrl/samsung.h>
> >
> > You probably also need <dt-bindings/interrupt-controller/arm-gic.h>
> > here for GIC_SPI definition.
> >
> >> +
> >> +&pinctrl_alive {
> >> + etc0: etc0 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + etc1: etc1 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >
> > Hmm, what are these two? I can't find anything related in
> > exynos7885.dtsi. If it's just some leftover from downstream vendor
> > kernel -- please remove it.
>
> This is a pinctrl DTSI file. What do you expect to find in
> exynos7885.dtsi for these? Why removing them?

etc0 and etc1 nodes are defined as gpio-controller and
interrupt-controller. So "compatible" should be provided somewhere for
those nodes. For example, for "gpa0" node below you can find its
compatible in exynos7885.dtsi. Right now I don't understand how those
etc0 and etc1 can be used at all. So maybe it's better to just remove
those? Those are not used anywhere and we probably don't even know
what those nodes represent. My point is, if those are actually some
leftovers from vendor kernel and those are not going to be used (and I
don't see how, without "compatible"), then we probablly better off
without those.

> >
> >> +
> >> + gpa0: gpa0 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + interrupt-parent = <&gic>;
> >> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> >> + };
> >> +
> >> + gpa1: gpa1 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <3>;
> >> + interrupt-parent = <&gic>;
> >> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> >> + };
> >> +
> >> + gpa2: gpa2 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpq0: gpq0 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + sim1_det_gpio: sim1-det-gpio-pins {
> >> + samsung,pins = "gpa2-5";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + sim0_det_gpio: sim0-det-gpio-pins {
> >> + samsung,pins = "gpa2-6";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + speedy_bus: speedy-bus-pins {
> >> + samsung,pins = "gpq0-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >
> > Here and below: suggest using EXYNOS5420_PIN_DRV_LV* constants. Then
> > stuff like "sd1_clk_fast_slew_rate_4x" is going to make sense.
> >
> >> + };
> >> +
> >> + /* UART_DEBUG */
> >> + uart2_bus: uart2-bus-pins {
> >> + samsung,pins = "gpq0-4", "gpq0-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +};
> >> +
> >> +&pinctrl_dispaud {
> >> + gpb0: gpb0 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpb1: gpb1 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpb2: gpb2 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + aud_codec_mclk: aud-codec-mclk-pins {
> >> + samsung,pins = "gpb0-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_codec_mclk_idle: aud-codec-mclk-idle-pins {
> >> + samsung,pins = "gpb0-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_codec_bus: aud-codec-bus-pins {
> >> + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_codec_bus_idle: aud-codec-bus-idle-pins {
> >> + samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_loopback_bus: aud-loopback-bus-pins {
> >> + samsung,pins = "gpb1-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_loopback_bus_idle: aud-loopback-bus-idle-pins {
> >> + samsung,pins = "gpb1-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_fm_bus: aud-fm-bus-pins {
> >> + samsung,pins = "gpb1-1", "gpb1-2", "gpb1-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_fm_bus_idle: aud-fm-bus-idle-pins {
> >> + samsung,pins = "gpb1-1", "gpb1-2", "gpb1-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_spk_bus: aud-spk-bus-pins {
> >> + samsung,pins = "gpb2-0", "gpb2-1", "gpb2-2", "gpb2-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +
> >> + aud_spk_bus_idle: aud-spk-bus-idle-pins {
> >> + samsung,pins = "gpb2-0", "gpb2-1", "gpb2-2", "gpb2-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + };
> >> +};
> >> +
> >> +&pinctrl_fsys {
> >> + gpf0: gpf0 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpf2: gpf2 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpf3: gpf3 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpf4: gpf4 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + sd0_clk: sd0-clk-pins {
> >> + samsung,pins = "gpf0-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x-pins {
> >> + samsung,pins = "gpf0-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x-pins {
> >> + samsung,pins = "gpf0-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <1>;
> >> + };
> >> +
> >> + sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x-pins {
> >> + samsung,pins = "gpf0-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x-pins {
> >> + samsung,pins = "gpf0-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd0_cmd: sd0-cmd-pins {
> >> + samsung,pins = "gpf0-1";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd0_rdqs: sd0-rdqs-pins {
> >> + samsung,pins = "gpf0-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd0_bus1: sd0-bus-width1-pins {
> >> + samsung,pins = "gpf2-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd0_bus4: sd0-bus-width4-pins {
> >> + samsung,pins = "gpf2-1", "gpf2-2", "gpf2-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd0_bus8: sd0-bus-width8-pins {
> >> + samsung,pins = "gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd1_clk: sd1-clk-pins {
> >> + samsung,pins = "gpf3-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd1_clk_fast_slew_rate_1x: sd1-clk-fast-slew-rate-1x-pins {
> >> + samsung,pins = "gpf3-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + sd1_clk_fast_slew_rate_2x: sd1-clk-fast-slew-rate-2x-pins {
> >> + samsung,pins = "gpf3-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <1>;
> >> + };
> >> +
> >> + sd1_clk_fast_slew_rate_3x: sd1-clk-fast-slew-rate-3x-pins {
> >> + samsung,pins = "gpf3-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd1_clk_fast_slew_rate_4x: sd1-clk-fast-slew-rate-4x-pins {
> >> + samsung,pins = "gpf3-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd1_cmd: sd1-cmd-pins {
> >> + samsung,pins = "gpf3-1";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd1_bus1: sd1-bus-width1-pins {
> >> + samsung,pins = "gpf3-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd1_bus4: sd1-bus-width4-pins {
> >> + samsung,pins = "gpf3-3", "gpf3-5";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd2_clk: sd2-clk-pins {
> >> + samsung,pins = "gpf4-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x-pins {
> >> + samsung,pins = "gpf4-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x-pins {
> >> + samsung,pins = "gpf4-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <1>;
> >> + };
> >> +
> >> + sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x-pins {
> >> + samsung,pins = "gpf4-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x-pins {
> >> + samsung,pins = "gpf4-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <3>;
> >> + };
> >> +
> >> + sd2_cmd: sd2-cmd-pins {
> >> + samsung,pins = "gpf4-1";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd2_bus1: sd2-bus-width1-pins {
> >> + samsung,pins = "gpf4-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +
> >> + sd2_bus4: sd2-bus-width4-pins {
> >> + samsung,pins = "gpf4-3", "gpf4-4", "gpf4-5";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <2>;
> >> + };
> >> +};
> >> +
> >> +&pinctrl_top {
> >> + gpc0: gpc0 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpc1: gpc1 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpc2: gpc2 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpg0: gpg0 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpg1: gpg1 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpg2: gpg2 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpg3: gpg3 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpg4: gpg4 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp0: gpp0 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp1: gpp1 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp2: gpp2 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp3: gpp3 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp4: gpp4 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp5: gpp5 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp6: gpp6 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp7: gpp7 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + gpp8: gpp8 {
> >> + gpio-controller;
> >> + #gpio-cells = <2>;
> >> +
> >> + interrupt-controller;
> >> + #interrupt-cells = <2>;
> >> + };
> >> +
> >> + /* DECON TE */
> >> + decon_f_te_on: decon_f_te_on-pins {
> >> + samsung,pins = "gpc0-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
> >> + };
> >> +
> >> + decon_f_te_off: decon_f_te_off-pins {
> >> + samsung,pins = "gpc0-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> >> + };
> >> +
> >> + hs_i2c0_bus: hs-i2c0-bus-pins {
> >> + samsung,pins = "gpc1-1", "gpc1-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + hs_i2c1_bus: hs-i2c1-bus-pins {
> >> + samsung,pins = "gpc1-3", "gpc1-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + hs_i2c2_bus: hs-i2c2-bus-pins {
> >> + samsung,pins = "gpc1-5", "gpc1-4";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + hs_i2c3_bus: hs-i2c3-bus-pins {
> >> + samsung,pins = "gpc1-7", "gpc1-6";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + /* USI0 UART */
> >> + uart3_bus_single: uart3-bus-single-pins {
> >> + samsung,pins = "gpc2-3", "gpc2-2", "gpc2-1", "gpc2-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + /* USI0 UART_HSI2C1 */
> >> + uart3_bus_dual: uart3-bus-dual-pins {
> >> + samsung,pins = "gpc2-1", "gpc2-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + /* USI0 HSI2C0 */
> >> + hs_i2c4_bus: hs-i2c4-bus-pins {
> >> + samsung,pins = "gpc2-1", "gpc2-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + /* USI0 HSI2C1 */
> >> + hs_i2c5_bus: hs-i2c5-bus-pins {
> >> + samsung,pins = "gpc2-3", "gpc2-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + /* USI0 SPI */
> >> + spi2_bus: spi2-bus-pins {
> >> + samsung,pins = "gpc2-1", "gpc2-0", "gpc2-3";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + spi2_cs: spi2-cs-pins {
> >> + samsung,pins = "gpc2-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + /* USI1 UART */
> >> + uart4_bus_single: uart4-bus-single-pins {
> >> + samsung,pins = "gpc2-7", "gpc2-6", "gpc2-5", "gpc2-4";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + /* USI1 UART_HSI2C1*/
> >> + uart4_bus_dual: uart4-bus-dual-pins {
> >> + samsung,pins = "gpc2-5", "gpc2-4";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + /* USI1 HSI2C0 */
> >> + hs_i2c6_bus: hs-i2c6-bus-pins {
> >> + samsung,pins = "gpc2-5", "gpc2-4";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + /* USI1 HSI2C1 */
> >> + hs_i2c7_bus: hs-i2c7-bus-pins {
> >> + samsung,pins = "gpc2-7", "gpc2-6";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + /* USI1 SPI */
> >> + spi3_bus: spi3-bus-pins {
> >> + samsung,pins = "gpc2-5", "gpc2-4", "gpc2-7";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + spi3_cs: spi3-cs-pins {
> >> + samsung,pins = "gpc2-6";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + fm_lna_en: fm-lna-en-pins {
> >> + samsung,pins = "gpg0-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-val = <1>;
> >> + };
> >> +
> >> + uart1_bus: uart1-bus-pins {
> >> + samsung,pins = "gpg1-3", "gpg1-2", "gpg1-1", "gpg1-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + i2c7_bus: i2c7-bus-pins {
> >> + samsung,pins = "gpg1-5", "gpg1-4";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + aud_dmic_on: aud-dmic-on-pins {
> >> + samsung,pins = "gpg2-1";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
> >> + samsung,pin-val = <1>;
> >> + };
> >> +
> >> + aud_dmic_off: aud-dmic-off-pins {
> >> + samsung,pins = "gpg2-1";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
> >> + samsung,pin-val = <0>;
> >> + };
> >> +
> >> + /* UART_HEALTH */
> >> + uart0_bus: uart0-bus-pins {
> >> + samsung,pins = "gpp0-3", "gpp0-2", "gpp0-1", "gpp0-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + i2c0_bus: i2c0-bus-pins {
> >> + samsung,pins = "gpp1-1", "gpp1-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + i2c1_bus: i2c1-bus-pins {
> >> + samsung,pins = "gpp1-3", "gpp1-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + i2c2_bus: i2c2-bus-pins {
> >> + samsung,pins = "gpp2-1", "gpp2-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + i2c3_bus: i2c3-bus-pins {
> >> + samsung,pins = "gpp3-1", "gpp3-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + i2c4_bus: i2c4-bus-pins {
> >> + samsung,pins = "gpp4-1", "gpp4-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + i2c5_bus: i2c5-bus-pins {
> >> + samsung,pins = "gpp4-3", "gpp4-2";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + i2c6_bus: i2c6-bus-pins {
> >> + samsung,pins = "gpp4-5", "gpp4-4";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + /* SPI_ESE */
> >> + spi0_bus: spi0-bus-pins {
> >> + samsung,pins = "gpp5-3", "gpp5-2", "gpp5-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + spi0_cs: spi0-cs-pins {
> >> + samsung,pins = "gpp5-1";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + /* SPI_FP */
> >> + spi1_bus: spi1-bus-pins {
> >> + samsung,pins = "gpp6-3", "gpp6-2", "gpp6-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + spi1_cs: spi1-cs-pins {
> >> + samsung,pins = "gpp6-1";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + /* USI2 UART */
> >> + uart5_bus_single: uart5-bus-single-pins {
> >> + samsung,pins = "gpp8-1", "gpp8-0", "gpp7-1", "gpp7-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + /* USI2 UART_HSI2C1 */
> >> + uart5_bus_dual: uart5-bus-dual-pins {
> >> + samsung,pins = "gpp7-1", "gpp7-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + };
> >> +
> >> + /* USI2 HSI2C0 */
> >> + hs_i2c8_bus: hs-i2c8-bus-pins {
> >> + samsung,pins = "gpp7-1", "gpp7-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + /* USI2 HSI2C1 */
> >> + hs_i2c9_bus: hs-i2c9-bus-pins {
> >> + samsung,pins = "gpp8-1", "gpp8-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> >> + samsung,pin-drv = <0>;
> >> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
> >> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
> >> + };
> >> +
> >> + /* USI2 SPI */
> >> + spi4_bus: spi4-bus-pins {
> >> + samsung,pins = "gpp7-1", "gpp7-0", "gpp8-1";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +
> >> + spi4_cs: spi4-cs-pins {
> >> + samsung,pins = "gpp8-0";
> >> + samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
> >> + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
> >> + samsung,pin-drv = <0>;
> >> + };
> >> +};
> >> diff --git a/arch/arm64/boot/dts/exynos/exynos7885.dtsi b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
> >> new file mode 100644
> >> index 000000000000..cc7a5ce0c103
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
> >> @@ -0,0 +1,438 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Samsung Exynos7885 SoC device tree source
> >> + *
> >> + * Copyright (c) 2021 Samsung Electronics Co., Ltd.
> >> + * Copyright (c) 2021 Dávid Virág
> >> + *
> >
> > This line is not needed.
> >
> >> + */
> >> +
> >> +#include <dt-bindings/clock/exynos7885.h>
> >> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> >> +
> >> +/ {
> >> + compatible = "samsung,exynos7885";
> >> + #address-cells = <2>;
> >> + #size-cells = <1>;
> >> +
> >> + interrupt-parent = <&gic>;
> >> +
> >> + aliases {
> >> + pinctrl0 = &pinctrl_alive;
> >> + pinctrl1 = &pinctrl_dispaud;
> >> + pinctrl2 = &pinctrl_fsys;
> >> + pinctrl3 = &pinctrl_top;
> >> + };
> >> +
> >> + arm-a53-pmu {
> >> + compatible = "arm,cortex-a53-pmu";
> >> + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
> >> + interrupt-affinity = <&cpu0>,
> >> + <&cpu1>,
> >> + <&cpu2>,
> >> + <&cpu3>,
> >> + <&cpu4>,
> >> + <&cpu5>;
> >
> > Maybe have cpu0..cpu3 on one line, and cpu4..cpu5 on second line?
>
> No, let's keep them aligned the same as interrupts. Easier to count
> total lines :)
>
> >
> >> + };
> >> +
> >> + arm-a73-pmu {
> >> + compatible = "arm,cortex-a73-pmu";
> >> + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
> >> + interrupt-affinity = <&cpu6>,
> >> + <&cpu7>;
> >
> > Both cpus can be on the same line here.
>
> Same.
>
> >
> >> + };
> >> +
> >> + cpus {
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> +
> >> + cpu-map {
> >> + cluster0 {
> >> + core0 {
> >> + cpu = <&cpu0>;
> >> + };
> >> + core1 {
> >> + cpu = <&cpu1>;
> >> + };
> >> + core2 {
> >> + cpu = <&cpu2>;
> >> + };
> >> + core3 {
> >> + cpu = <&cpu3>;
> >> + };
> >> + core4 {
> >> + cpu = <&cpu4>;
> >> + };
> >> + core5 {
> >> + cpu = <&cpu5>;
> >> + };
> >> + };
> >> +
> >> + cluster1 {
> >> + core0 {
> >> + cpu = <&cpu6>;
> >> + };
> >> + core1 {
> >> + cpu = <&cpu7>;
> >> + };
> >> + };
> >> + };
> >> +
> >> + cpu0: cpu@100 {
> >> + device_type = "cpu";
> >> + compatible = "arm,cortex-a53";
> >> + reg = <0x100>;
> >> + enable-method = "psci";
> >> + };
> >> +
> >> + cpu1: cpu@101 {
> >> + device_type = "cpu";
> >> + compatible = "arm,cortex-a53";
> >> + reg = <0x101>;
> >> + enable-method = "psci";
> >> + };
> >> +
> >> + cpu2: cpu@102 {
> >> + device_type = "cpu";
> >> + compatible = "arm,cortex-a53";
> >> + reg = <0x102>;
> >> + enable-method = "psci";
> >> + };
> >> +
> >> + cpu3: cpu@103 {
> >> + device_type = "cpu";
> >> + compatible = "arm,cortex-a53";
> >> + reg = <0x103>;
> >> + enable-method = "psci";
> >> + };
> >> +
> >> + cpu4: cpu@200 {
> >> + device_type = "cpu";
> >> + compatible = "arm,cortex-a53";
> >> + reg = <0x200>;
> >> + enable-method = "psci";
> >> + };
> >> +
> >> + cpu5: cpu@201 {
> >> + device_type = "cpu";
> >> + compatible = "arm,cortex-a53";
> >> + reg = <0x201>;
> >> + enable-method = "psci";
> >> + };
> >> +
> >> + cpu6: cpu@0 {
> >> + device_type = "cpu";
> >> + compatible = "arm,cortex-a73";
> >> + reg = <0x0>;
> >> + enable-method = "psci";
> >> + };
> >> +
> >> + cpu7: cpu@1 {
> >> + device_type = "cpu";
> >> + compatible = "arm,cortex-a73";
> >> + reg = <0x1>;
> >> + enable-method = "psci";
> >> + };
> >> + };
> >> +
> >> + psci {
> >> + compatible = "arm,psci";
> >> + method = "smc";
> >> + cpu_suspend = <0xc4000001>;
> >> + cpu_off = <0x84000002>;
> >> + cpu_on = <0xc4000003>;
> >> + };
> >> +
> >> + timer {
> >> + compatible = "arm,armv8-timer";
> >> + /* Hypervisor Virtual Timer interrupt is not wired to GIC */
> >> + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> >> + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> >> + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> >> + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> >
> > Can you please make it fit 80 characters per line?
>
> This exceeds only by 9 characters and is more readable than split. Keep
> it like this, please.
>
> >
> >> + };
> >> +
> >> + fixed-rate-clocks {
> >> + oscclk: osc-clock {
> >> + compatible = "fixed-clock";
> >> + #clock-cells = <0>;
> >> + clock-frequency = <26000000>;
> >
> > Hmm, maybe it's better to set this clock frequency in board dts?
>
> Good point, frequency should be in DTS.
> >
> >> + clock-output-names = "oscclk";
> >> + };
> >> + };
> >> +
> >> + soc: soc@0 {
> >> + compatible = "simple-bus";
> >> + #address-cells = <1>;
> >> + #size-cells = <1>;
> >> + ranges = <0x0 0x0 0x0 0x20000000>;
> >> +
> >> + chipid@10000000 {
> >> + compatible = "samsung,exynos850-chipid";
> >> + reg = <0x10000000 0x24>;
> >> + };
> >> +
> >> + gic: interrupt-controller@12301000 {
> >> + compatible = "arm,gic-400";
> >> + #interrupt-cells = <3>;
> >> + #address-cells = <0>;
> >> + interrupt-controller;
> >> + reg = <0x12301000 0x1000>,
> >> + <0x12302000 0x2000>,
> >> + <0x12304000 0x2000>,
> >> + <0x12306000 0x2000>;
> >> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
> >> + IRQ_TYPE_LEVEL_HIGH)>;
> >> + };
> >> +
> >> + cmu_peri: clock-controller@10010000 {
> >> + compatible = "samsung,exynos7885-cmu-peri";
> >> + reg = <0x10010000 0x8000>;
> >> + #clock-cells = <1>;
> >> +
> >> + clocks = <&oscclk>,
> >> + <&cmu_top CLK_DOUT_PERI_BUS>,
> >> + <&cmu_top CLK_DOUT_PERI_SPI0>,
> >> + <&cmu_top CLK_DOUT_PERI_SPI1>,
> >> + <&cmu_top CLK_DOUT_PERI_UART0>,
> >> + <&cmu_top CLK_DOUT_PERI_UART1>,
> >> + <&cmu_top CLK_DOUT_PERI_UART2>,
> >> + <&cmu_top CLK_DOUT_PERI_USI0>,
> >> + <&cmu_top CLK_DOUT_PERI_USI1>,
> >> + <&cmu_top CLK_DOUT_PERI_USI2>;
> >> + clock-names = "oscclk",
> >> + "dout_peri_bus",
> >> + "dout_peri_spi0",
> >> + "dout_peri_spi1",
> >> + "dout_peri_uart0",
> >> + "dout_peri_uart1",
> >> + "dout_peri_uart2",
> >> + "dout_peri_usi0",
> >> + "dout_peri_usi1",
> >> + "dout_peri_usi2";
> >> + };
> >> +
> >> + cmu_core: clock-controller@12000000 {
> >> + compatible = "samsung,exynos7885-cmu-core";
> >> + reg = <0x12000000 0x8000>;
> >> + #clock-cells = <1>;
> >> +
> >> + clocks = <&oscclk>,
> >> + <&cmu_top CLK_DOUT_CORE_BUS>,
> >> + <&cmu_top CLK_DOUT_CORE_CCI>,
> >> + <&cmu_top CLK_DOUT_CORE_G3D>;
> >> + clock-names = "oscclk", "dout_core_bus", "dout_core_cci", "dout_core_g3d";
> >
> > 80 characters per line, please. Also, please keep the style
> > consistent: in cmu_peri you have each clock per line, here all clocks
> > are on one line.
>
> +1
>
> >
> >> + };
> >> +
> >> + cmu_top: clock-controller@12060000 {
> >
> > I'd move cmu_top above, to be the first CMU node.
>
> No, let's keep them ordered by unit addresses, at least within each
> group (so within clock controllers, pinctrl nodes etc). Ordering by
> numbers is objective, while keeping order by some hierarchy requires
> knowing this hierarchy and actually agreeing on it. :)
>
> >
> >> + compatible = "samsung,exynos7885-cmu-top";
> >> + reg = <0x12060000 0x8000>;
> >> + #clock-cells = <1>;
> >> +
> >> + clocks = <&oscclk>;
> >> + clock-names = "oscclk";
> >> + };
> >> +
> >> + pinctrl_alive: pinctrl@11cb0000 {
> >> + compatible = "samsung,exynos7885-pinctrl";
> >> + reg = <0x11cb0000 0x1000>;
> >> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
> >> + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
> >> +
> >> + wakeup-interrupt-controller {
> >> + compatible = "samsung,exynos7-wakeup-eint";
> >> + interrupt-parent = <&gic>;
> >> + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
> >> + };
> >> + };
> >> +
> >> + pinctrl_dispaud: pinctrl@148f0000 {
> >> + compatible = "samsung,exynos7885-pinctrl";
> >> + reg = <0x148f0000 0x1000>;
> >> + interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
> >> + };
> >> +
> >> + pinctrl_fsys: pinctrl@13430000 {
> >> + compatible = "samsung,exynos7885-pinctrl";
> >> + reg = <0x13430000 0x1000>;
> >> + interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
> >> + };
> >> +
> >> + pinctrl_top: pinctrl@139b0000 {
> >> + compatible = "samsung,exynos7885-pinctrl";
> >> + reg = <0x139b0000 0x1000>;
> >> + interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
> >> + };
> >> +
> >> + pmu_system_controller: system-controller@11c80000 {
> >> + compatible = "samsung,exynos7-pmu", "syscon";
> >> + reg = <0x11c80000 0x10000>;
> >> + };
> >> +
> >> + serial_0: serial@13800000 {
> >> + compatible = "samsung,exynos5433-uart";
> >> + reg = <0x13800000 0x100>;
> >> + interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&uart0_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_UART0_EXT_UCLK>,
> >> + <&cmu_peri CLK_GOUT_UART0_PCLK>;
> >
> > AFAIU, usually PCLK is a bus clock. Are you sure it should be UART baud clock?
> >
> >> + clock-names = "uart", "clk_uart_baud0";
> >> + samsung,uart-fifosize = <64>;
> >> + status = "disabled";
> >> + };
> >> +
> >> + serial_1: serial@13810000 {
> >> + compatible = "samsung,exynos5433-uart";
> >> + reg = <0x13810000 0x100>;
> >> + interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&uart1_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_UART1_EXT_UCLK>,
> >> + <&cmu_peri CLK_GOUT_UART1_PCLK>;
> >> + clock-names = "uart", "clk_uart_baud0";
> >> + samsung,uart-fifosize = <256>;
> >> + status = "disabled";
> >> + };
> >> +
> >> + serial_2: serial@13820000 {
> >> + compatible = "samsung,exynos5433-uart";
> >> + reg = <0x13820000 0x100>;
> >> + interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&uart2_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_UART2_EXT_UCLK>,
> >> + <&cmu_peri CLK_GOUT_UART2_PCLK>;
> >> + clock-names = "uart", "clk_uart_baud0";
> >> + samsung,uart-fifosize = <256>;
> >> + status = "disabled";
> >> + };
> >> +
> >> + i2c_0: i2c@13830000 {
> >> + compatible = "samsung,s3c2440-i2c";
> >> + reg = <0x13830000 0x100>;
> >> + interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c0_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_I2C0_PCLK>;
> >> + clock-names = "i2c";
> >> + status = "disabled";
> >> + };
> >> +
> >> + i2c_1: i2c@13840000 {
> >> + compatible = "samsung,s3c2440-i2c";
> >> + reg = <0x13840000 0x100>;
> >> + interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c1_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_I2C1_PCLK>;
> >> + clock-names = "i2c";
> >> + status = "disabled";
> >> + };
> >> +
> >> + i2c_2: i2c@13850000 {
> >> + compatible = "samsung,s3c2440-i2c";
> >> + reg = <0x13850000 0x100>;
> >> + interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c2_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_I2C2_PCLK>;
> >> + clock-names = "i2c";
> >> + status = "disabled";
> >> + };
> >> +
> >> + i2c_3: i2c@13860000 {
> >> + compatible = "samsung,s3c2440-i2c";
> >> + reg = <0x13860000 0x100>;
> >> + interrupts = <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c3_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_I2C3_PCLK>;
> >> + clock-names = "i2c";
> >> + status = "disabled";
> >> + };
> >> +
> >> + i2c_4: i2c@13870000 {
> >> + compatible = "samsung,s3c2440-i2c";
> >> + reg = <0x13870000 0x100>;
> >> + interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c4_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_I2C4_PCLK>;
> >> + clock-names = "i2c";
> >> + status = "disabled";
> >> + };
> >> +
> >> + i2c_5: i2c@13880000 {
> >> + compatible = "samsung,s3c2440-i2c";
> >> + reg = <0x13880000 0x100>;
> >> + interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c5_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_I2C5_PCLK>;
> >> + clock-names = "i2c";
> >> + status = "disabled";
> >> + };
> >> +
> >> + i2c_6: i2c@13890000 {
> >> + compatible = "samsung,s3c2440-i2c";
> >> + reg = <0x13890000 0x100>;
> >> + interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c6_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_I2C6_PCLK>;
> >> + clock-names = "i2c";
> >> + status = "disabled";
> >> + };
> >> +
> >> + i2c_7: i2c@11cd0000 {
> >> + compatible = "samsung,s3c2440-i2c";
> >> + reg = <0x11cd0000 0x100>;
> >> + interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&i2c7_bus>;
> >> + clocks = <&cmu_peri CLK_GOUT_I2C7_PCLK>;
> >> + clock-names = "i2c";
> >> + status = "disabled";
> >> + };
> >> + };
> >> +};
> >> +
> >> +#include "exynos7885-pinctrl.dtsi"
> >> +#include "arm/exynos-syscon-restart.dtsi"
> >
> > Have you verified both reboot and power off functions from this file?
> > I guess if some doesn't work, it's better to avoid including this, but
> > instead add corresponding sub-nodes into your pmu_sytem_controller.
>
> Why open-coding same code work and including would not? Assuming that it
> compiles, of course.
>

For example, in case of Exynos850 the "power off" node from this file
wasn't suitable. In that case it's not worth including it. But David
already confirmed both work fine for him, so it doesn't matter
anymore.

>
> Best regards,
> Krzysztof

\
 
 \ /
  Last update: 2021-12-08 16:39    [W:0.170 / U:2.048 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site