lkml.org 
[lkml]   [2021]   [Dec]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH 5.15 184/207] serial: 8250_bcm7271: UART errors after resuming from S2
Date
From: Al Cooper <alcooperx@gmail.com>

[ Upstream commit 9cabe26e65a893afd5846908aa393bd283ab6609 ]

There is a small window in time during resume where the hardware
flow control signal RTS can be asserted (which allows a sender to
resume sending data to the UART) but the baud rate has not yet
been restored. This will cause corrupted data and FRAMING, OVERRUN
and BREAK errors. This is happening because the MCTRL register is
shadowed in uart_port struct and is later used during resume to set
the MCTRL register during both serial8250_do_startup() and
uart_resume_port(). Unfortunately, serial8250_do_startup()
happens before the UART baud rate is restored. The fix is to clear
the shadowed mctrl value at the end of suspend and restore it at the
end of resume.

Fixes: 41a469482de2 ("serial: 8250: Add new 8250-core based Broadcom STB driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Link: https://lore.kernel.org/r/20211201201402.47446-1-alcooperx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/tty/serial/8250/8250_bcm7271.c | 13 +++++++++++++
1 file changed, 13 insertions(+)

diff --git a/drivers/tty/serial/8250/8250_bcm7271.c b/drivers/tty/serial/8250/8250_bcm7271.c
index 7f656fac503fe..5163d60756b73 100644
--- a/drivers/tty/serial/8250/8250_bcm7271.c
+++ b/drivers/tty/serial/8250/8250_bcm7271.c
@@ -237,6 +237,7 @@ struct brcmuart_priv {
u32 rx_err;
u32 rx_timeout;
u32 rx_abort;
+ u32 saved_mctrl;
};

static struct dentry *brcmuart_debugfs_root;
@@ -1133,16 +1134,27 @@ static int brcmuart_remove(struct platform_device *pdev)
static int __maybe_unused brcmuart_suspend(struct device *dev)
{
struct brcmuart_priv *priv = dev_get_drvdata(dev);
+ struct uart_8250_port *up = serial8250_get_port(priv->line);
+ struct uart_port *port = &up->port;

serial8250_suspend_port(priv->line);
clk_disable_unprepare(priv->baud_mux_clk);

+ /*
+ * This will prevent resume from enabling RTS before the
+ * baud rate has been resored.
+ */
+ priv->saved_mctrl = port->mctrl;
+ port->mctrl = 0;
+
return 0;
}

static int __maybe_unused brcmuart_resume(struct device *dev)
{
struct brcmuart_priv *priv = dev_get_drvdata(dev);
+ struct uart_8250_port *up = serial8250_get_port(priv->line);
+ struct uart_port *port = &up->port;
int ret;

ret = clk_prepare_enable(priv->baud_mux_clk);
@@ -1165,6 +1177,7 @@ static int __maybe_unused brcmuart_resume(struct device *dev)
start_rx_dma(serial8250_get_port(priv->line));
}
serial8250_resume_port(priv->line);
+ port->mctrl = priv->saved_mctrl;
return 0;
}

--
2.33.0


\
 
 \ /
  Last update: 2021-12-06 17:11    [W:2.112 / U:0.960 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site