lkml.org 
[lkml]   [2021]   [Dec]   [6]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] soc: imx: gpcv2: Enable vpumix/dispmix to wait for handshake
From
Date
Hi Shawn,

Am Montag, dem 06.12.2021 um 08:45 +0800 schrieb Shawn Guo:
> Hi Lucas,
>
> What's your take on this one?
>
Thanks for asking. This patch is incorrect. The handshake will only be
completed once all the clocks for the ADB are enabled, which is done in
the blk-ctrl driver. The blk-ctrl driver however can only do so _after_
the power-up sequence of the GPC domain is completed, so waiting for
the handshake in the middle of the power-up sequence is not going to
work for most of the GPC domains. Please drop this patch.

Regards,
Lucas

> Shawn
>
> On Sat, Nov 20, 2021 at 01:49:00PM -0600, Adam Ford wrote:
> > There is a comment in the code that states the driver needs to
> > wait for the handshake, but it's only available when the bus
> > has been enabled from the blk-ctrl. Since both the
> > vpumix and dispmix are called from the blk-ctl, it seems
> > reasonable to assume the bus is enabled. Add a bool to determine
> > which power-domains are able to properly wait for this
> > handshake and set the corresping boolean for the two domains
> > activated by the blk-ctrl.
> >
> > Signed-off-by: Adam Ford <aford173@gmail.com>
> >
> > diff --git a/drivers/soc/imx/gpcv2.c b/drivers/soc/imx/gpcv2.c
> > index 7b6dfa33dcb9..a957f7fff968 100644
> > --- a/drivers/soc/imx/gpcv2.c
> > +++ b/drivers/soc/imx/gpcv2.c
> > @@ -204,6 +204,7 @@ struct imx_pgc_domain {
> > const int voltage;
> > const bool keep_clocks;
> > struct device *dev;
> > + bool blkctrl_bus_enabled;
> > };
> >
> > struct imx_pgc_domain_data {
> > @@ -282,17 +283,14 @@ static int imx_pgc_power_up(struct generic_pm_domain *genpd)
> > domain->bits.hskreq, domain->bits.hskreq);
> >
> > /*
> > - * ret = regmap_read_poll_timeout(domain->regmap, GPC_PU_PWRHSK, reg_val,
> > - * (reg_val & domain->bits.hskack), 0,
> > - * USEC_PER_MSEC);
> > - * Technically we need the commented code to wait handshake. But that needs
> > - * the BLK-CTL module BUS clk-en bit being set.
> > - *
> > - * There is a separate BLK-CTL module and we will have such a driver for it,
> > - * that driver will set the BUS clk-en bit and handshake will be triggered
> > - * automatically there. Just add a delay and suppose the handshake finish
> > - * after that.
> > + * blkctrl_bus_enabled implies that the GPC is being invoked from a blk-ctrl
> > + * and not from a peripheral or other GPC power domain. The blk-ctrl is required
> > + * to support the handshake.
> > */
> > + if (domain->blkctrl_bus_enabled)
> > + ret = regmap_read_poll_timeout(domain->regmap, GPC_PU_PWRHSK, reg_val,
> > + (reg_val & domain->bits.hskack), 0,
> > + USEC_PER_MSEC);
> > }
> >
> > /* Disable reset clocks for all devices in the domain */
> > @@ -701,6 +699,7 @@ static const struct imx_pgc_domain imx8mm_pgc_domains[] = {
> > },
> > .pgc = BIT(IMX8MM_PGC_VPUMIX),
> > .keep_clocks = true,
> > + .blkctrl_bus_enabled = true,
> > },
> >
> > [IMX8MM_POWER_DOMAIN_VPUG1] = {
> > @@ -749,6 +748,7 @@ static const struct imx_pgc_domain imx8mm_pgc_domains[] = {
> > },
> > .pgc = BIT(IMX8MM_PGC_DISPMIX),
> > .keep_clocks = true,
> > + .blkctrl_bus_enabled = true,
> > },
> >
> > [IMX8MM_POWER_DOMAIN_MIPI] = {
> > --
> > 2.32.0
> >


\
 
 \ /
  Last update: 2021-12-06 10:11    [W:0.244 / U:0.116 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site