lkml.org 
[lkml]   [2021]   [Dec]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH v6 2/2] misc: Add iop driver for Sunplus SP7021
On Thu, Dec 30, 2021 at 08:51:45PM +0800, Tony Huang wrote:
> IOP(8051) embedded inside SP7021 which is used as
> Processor for I/O control, monitor RTC interrupt and
> cooperation with CPU & PMC in power management purpose.
> The IOP core is DQ8051, so also named IOP8051,
> it supports dedicated JTAG debug pins which share with SP7021.
> In standby mode operation, the power spec reach 400uA.
>
> Signed-off-by: Tony Huang <tonyhuang.sunplus@gmail.com>
> ---
> Changes in v6:
> - Added sysfs read/write description.
> - Modify sysfs read function.
> - Addressed comments from kernel test robot.
>
> Documentation/ABI/testing/sysfs-platform-soc@B | 25 ++
> MAINTAINERS | 2 +
> drivers/misc/Kconfig | 12 +
> drivers/misc/Makefile | 1 +
> drivers/misc/sunplus_iop.c | 476 +++++++++++++++++++++++++
> 5 files changed, 516 insertions(+)
> create mode 100644 Documentation/ABI/testing/sysfs-platform-soc@B
> create mode 100644 drivers/misc/sunplus_iop.c
>
> diff --git a/Documentation/ABI/testing/sysfs-platform-soc@B b/Documentation/ABI/testing/sysfs-platform-soc@B
> new file mode 100644
> index 0000000..6272919
> --- /dev/null
> +++ b/Documentation/ABI/testing/sysfs-platform-soc@B
> @@ -0,0 +1,25 @@
> +What: /sys/devices/platform/soc@B/9c000400.iop/sp_iop_mailbox
> +Date: December 2021
> +KernelVersion: 5.16
> +Contact: Tony Huang <tonyhuang.sunplus@gmail.com>
> +Description:
> + Show 8051 mailbox0 data.

What format is the data in?



> +
> +What: /sys/devices/platform/soc@B/9c000400.iop/sp_iop_mode
> +Date: December 2021
> +KernelVersion: 5.16
> +Contact: Tony Huang <tonyhuang.sunplus@gmail.com>
> +Description:
> + Read-Write.
> +
> + Write this file.
> + Operation mode of IOP is switched to standby mode by writing
> + "1" to sysfs.
> + Operation mode of IOP is switched to normal mode by writing
> + "0" to sysfs.
> +
> + Read this file.
> + Show operation mode of IOP. "0" is normal mode. "1" is standby
> + mode.
> +
> +
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 6f336c9..cbc8dff 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -18245,7 +18245,9 @@ F: drivers/net/ethernet/dlink/sundance.c
> SUNPLUS IOP DRIVER
> M: Tony Huang <tonyhuang.sunplus@gmail.com>
> S: Maintained
> +F: Documentation/ABI/testing/sysfs-platform-soc@B
> F: Documentation/devicetree/bindings/misc/sunplu-iop.yaml
> +F: drivers/misc/sunplus_iop.c
>
> SUPERH
> M: Yoshinori Sato <ysato@users.sourceforge.jp>
> diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig
> index 0f5a49f..45655ea 100644
> --- a/drivers/misc/Kconfig
> +++ b/drivers/misc/Kconfig
> @@ -470,6 +470,18 @@ config HISI_HIKEY_USB
> switching between the dual-role USB-C port and the USB-A host ports
> using only one USB controller.
>
> +config SUNPLUS_IOP
> + tristate "Sunplus IOP support"
> + default ARCH_SUNPLUS
> + help
> + Sunplus I/O processor (8051) driver.
> + Processor for I/O control, RTC wake-up proceduce management,
> + and cooperation with CPU&PMC in power management.
> + Need Install DQ8051, The DQ8051 bin file generated by keil C.

I do not understand this sentence, what do you mean by it? Can you
provide a link to where the files that are required are? Why not
include them in the linux-firmware project?

> +
> + This driver can also be built as a module. If so, the module
> + will be called sunplus_iop.
> +
> source "drivers/misc/c2port/Kconfig"
> source "drivers/misc/eeprom/Kconfig"
> source "drivers/misc/cb710/Kconfig"
> diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
> index a086197..eafeab6 100644
> --- a/drivers/misc/Makefile
> +++ b/drivers/misc/Makefile
> @@ -52,6 +52,7 @@ obj-$(CONFIG_DW_XDATA_PCIE) += dw-xdata-pcie.o
> obj-$(CONFIG_PCI_ENDPOINT_TEST) += pci_endpoint_test.o
> obj-$(CONFIG_OCXL) += ocxl/
> obj-$(CONFIG_BCM_VK) += bcm-vk/
> +obj-$(CONFIG_SUNPLUS_IOP) += sunplus_iop.o
> obj-y += cardreader/
> obj-$(CONFIG_PVPANIC) += pvpanic/
> obj-$(CONFIG_HABANA_AI) += habanalabs/
> diff --git a/drivers/misc/sunplus_iop.c b/drivers/misc/sunplus_iop.c
> new file mode 100644
> index 0000000..a16d9e6
> --- /dev/null
> +++ b/drivers/misc/sunplus_iop.c
> @@ -0,0 +1,476 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * The IOP driver for Sunplus SP7021
> + *
> + * Copyright (C) 2021 Sunplus Technology Inc.
> + *
> + * All Rights Reserved.
> + */
> +#include <linux/delay.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/firmware.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/miscdevice.h>
> +#include <linux/of_platform.h>
> +#include <linux/of_address.h>
> +#include <linux/of_gpio.h>
> +
> +enum IOP_Status_e {
> + IOP_SUCCESS, /* successful */
> + IOP_ERR_IOP_BUSY, /* IOP is busy */
> +};
> +
> +struct regs_moon0 {
> + u32 stamp; /* 00 */
> + u32 clken[10]; /* 01~10 */
> + u32 gclken[10]; /* 11~20 */
> + u32 reset[10]; /* 21~30 */
> + u32 sfg_cfg_mode; /* 31 */

What are these comments numbering?

> +};
> +
> +struct regs_iop {
> + u32 iop_control;/* 00 */
> + u32 iop_reg1;/* 01 */
> + u32 iop_bp;/* 02 */
> + u32 iop_regsel;/* 03 */
> + u32 iop_regout;/* 04 */
> + u32 iop_reg5;/* 05 */
> + u32 iop_resume_pcl;/* 06 */
> + u32 iop_resume_pch;/* 07 */
> + u32 iop_data0;/* 08 */
> + u32 iop_data1;/* 09 */
> + u32 iop_data2;/* 10 */
> + u32 iop_data3;/* 11 */
> + u32 iop_data4;/* 12 */
> + u32 iop_data5;/* 13 */
> + u32 iop_data6;/* 14 */
> + u32 iop_data7;/* 15 */
> + u32 iop_data8;/* 16 */
> + u32 iop_data9;/* 17 */
> + u32 iop_data10;/* 18 */
> + u32 iop_data11;/* 19 */
> + u32 iop_base_adr_l;/* 20 */
> + u32 iop_base_adr_h;/* 21 */
> + u32 memory_bridge_control;/* 22 */
> + u32 iop_regmap_adr_l;/* 23 */
> + u32 iop_regmap_adr_h;/* 24 */
> + u32 iop_direct_adr;/* 25*/
> + u32 reserved[6];/* 26~31 */

Same here, what are these numbers?

And why are they not lined up like the previous structure?


> +};
> +
> +struct regs_iop_pmc {
> + u32 PMC_TIMER;/* 00 */
> + u32 PMC_CTRL;/* 01 */
> + u32 XTAL27M_PASSWORD_I;/* 02 */
> + u32 XTAL27M_PASSWORD_II;/* 03 */
> + u32 XTAL32K_PASSWORD_I;/* 04 */
> + u32 XTAL32K_PASSWORD_II;/* 05 */
> + u32 CLK27M_PASSWORD_I;/* 06 */
> + u32 CLK27M_PASSWORD_II;/* 07 */
> + u32 PMC_TIMER2;/* 08 */
> + u32 reserved[23];/* 9~31 */

Same comment question here.

> +};
> +
> +#define NORMAL_CODE_MAX_SIZE 0X1000

"0x"?

> +#define STANDBY_CODE_MAX_SIZE 0x4000

What are these for?

> +struct sp_iop {
> + struct miscdevice dev; // iop device

Why the comment?

> + struct mutex write_lock;
> + void *iop_regs;
> + void *pmc_regs;
> + void *moon0_regs;

Why void pointers? You created structures above, use them!

This is not Windows programming :)


> + int irq;
> + int gpio_wakeup;
> + unsigned char iop_normal_code[NORMAL_CODE_MAX_SIZE];
> + unsigned char iop_standby_code[STANDBY_CODE_MAX_SIZE];
> + resource_size_t iop_mem_start;
> + resource_size_t iop_mem_size;
> + bool mode;

How can a "mode" be boolean? Perhaps a better name?

> +};
> +
> +static void sp_iop_normal_mode(struct sp_iop *iop)
> +{
> + struct regs_iop *p_iop_reg = (struct regs_iop *)iop->iop_regs;

See, don't use a void pointer, use the real structure please.

> + struct regs_moon0 *p_moon0_reg = (struct regs_moon0 *)iop->moon0_regs;
> + void *iop_kernel_base;

Why void? Isn't this a structure too?

> + unsigned int reg;
> +
> + iop_kernel_base = ioremap(iop->iop_mem_start, NORMAL_CODE_MAX_SIZE);
> + memset(iop_kernel_base, 0, NORMAL_CODE_MAX_SIZE);
> + memcpy(iop_kernel_base, iop->iop_normal_code, NORMAL_CODE_MAX_SIZE);
> +
> + writel(0x00100010, &p_moon0_reg->clken[0]);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg |= 0x01;
> + writel(reg, &p_iop_reg->iop_control);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg &= ~(0x8000);
> + writel(reg, &p_iop_reg->iop_control);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg |= 0x0200;//disable watchdog event reset IOP
> + writel(reg, &p_iop_reg->iop_control);
> +
> + reg = (iop->iop_mem_start & 0xFFFF);
> + writel(reg, &p_iop_reg->iop_base_adr_l);
> + reg = (iop->iop_mem_start >> 16);
> + writel(reg, &p_iop_reg->iop_base_adr_h);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg &= ~(0x01);
> + writel(reg, &p_iop_reg->iop_control);
> + iop->mode = 0;
> +}
> +
> +static void sp_iop_standby_mode(struct sp_iop *iop)
> +{
> + struct regs_iop *p_iop_reg = (struct regs_iop *)iop->iop_regs;
> + struct regs_moon0 *p_moon0_reg = (struct regs_moon0 *)iop->moon0_regs;
> + void *iop_kernel_base;
> + unsigned long reg;
> +
> + iop_kernel_base = ioremap(iop->iop_mem_start, STANDBY_CODE_MAX_SIZE);
> + memset(iop_kernel_base, 0, STANDBY_CODE_MAX_SIZE);
> + memcpy(iop_kernel_base, iop->iop_standby_code, STANDBY_CODE_MAX_SIZE);
> +
> + writel(0x00100010, &p_moon0_reg->clken[0]);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg |= 0x01;
> + writel(reg, &p_iop_reg->iop_control);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg &= ~(0x8000);
> + writel(reg, &p_iop_reg->iop_control);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg |= 0x0200;//disable watchdog event reset IOP
> + writel(reg, &p_iop_reg->iop_control);
> +
> + reg = (iop->iop_mem_start & 0xFFFF);
> + writel(reg, &p_iop_reg->iop_base_adr_l);
> + reg = (iop->iop_mem_start >> 16);
> + writel(reg, &p_iop_reg->iop_base_adr_h);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg &= ~(0x01);
> + writel(reg, &p_iop_reg->iop_control);
> + iop->mode = 1;
> +}
> +
> +#define IOP_READY 0x4
> +#define RISC_READY 0x8
> +#define WAKEUP_PIN 0xFE02
> +#define S1 0x5331
> +#define S3 0x5333


What are these values for?

> +static int sp_iop_s3mode(struct device *dev, struct sp_iop *iop)
> +{
> + struct regs_iop *p_iop_reg = (struct regs_iop *)iop->iop_regs;
> + struct regs_moon0 *p_moon0_reg = (struct regs_moon0 *)iop->moon0_regs;
> + struct regs_iop_pmc *p_iop_pmc_reg = (struct regs_iop_pmc *)iop->pmc_regs;
> + unsigned int reg;
> + int ret, value;
> +
> + writel(0x00100010, &p_moon0_reg->clken[0]);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg &= ~(0x8000);
> + writel(reg, &p_iop_reg->iop_control);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg |= 0x1;
> + writel(reg, &p_iop_reg->iop_control);
> +
> + //PMC set
> + writel(0x00010001, &p_iop_pmc_reg->PMC_TIMER);
> + reg = readl(&p_iop_pmc_reg->PMC_CTRL);
> + reg |= 0x23;// disable system reset PMC, enalbe power down 27M, enable gating 27M

What is "27M"?

> + writel(reg, &p_iop_pmc_reg->PMC_CTRL);
> +
> + writel(0x55aa00ff, &p_iop_pmc_reg->XTAL27M_PASSWORD_I);
> + writel(0x00ff55aa, &p_iop_pmc_reg->XTAL27M_PASSWORD_II);
> + writel(0xaa00ff55, &p_iop_pmc_reg->XTAL32K_PASSWORD_I);
> + writel(0xff55aa00, &p_iop_pmc_reg->XTAL32K_PASSWORD_II);
> + writel(0xaaff0055, &p_iop_pmc_reg->CLK27M_PASSWORD_I);
> + writel(0x5500aaff, &p_iop_pmc_reg->CLK27M_PASSWORD_II);
> + writel(0x01000100, &p_iop_pmc_reg->PMC_TIMER2);
> +
> + //IOP Hardware IP reset

Always put a ' ' after '//'


> + reg = readl(&p_moon0_reg->reset[0]);
> + reg |= 0x10;
> + writel(reg, (&p_moon0_reg->reset[0]));
> + reg &= ~(0x10);
> + writel(reg, (&p_moon0_reg->reset[0]));
> +
> + writel(0x00ff0085, (iop->moon0_regs + 32 * 4 * 1 + 4 * 1));
> +
> + reg = readl(iop->moon0_regs + 32 * 4 * 1 + 4 * 2);
> + reg |= 0x08000800;
> + writel(reg, (iop->moon0_regs + 32 * 4 * 1 + 4 * 2));
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg |= 0x0200;//disable watchdog event reset IOP
> + writel(reg, &p_iop_reg->iop_control);
> +
> + reg = (iop->iop_mem_start & 0xFFFF);
> + writel(reg, &p_iop_reg->iop_base_adr_l);
> + reg = (iop->iop_mem_start >> 16);
> + writel(reg, &p_iop_reg->iop_base_adr_h);
> +
> + reg = readl(&p_iop_reg->iop_control);
> + reg &= ~(0x01);
> + writel(reg, &p_iop_reg->iop_control);
> +
> + writel(WAKEUP_PIN, &p_iop_reg->iop_data0);
> + writel(iop->gpio_wakeup, &p_iop_reg->iop_data1);
> +
> + ret = readl_poll_timeout(&p_iop_reg->iop_data2, value,
> + (value & IOP_READY) == IOP_READY, 1000, 10000);
> + if (ret) {
> + dev_err(dev, "timed out\n");
> + return ret;
> + }
> +
> + writel(RISC_READY, &p_iop_reg->iop_data2);
> + writel(0x00, &p_iop_reg->iop_data5);
> + writel(0x60, &p_iop_reg->iop_data6);
> +
> + ret = readl_poll_timeout(&p_iop_reg->iop_data7, value,
> + value == 0xaaaa, 1000, 10000);
> + if (ret) {
> + dev_err(dev, "timed out\n");
> + return ret;
> + }
> +
> + writel(0xdd, &p_iop_reg->iop_data1);//8051 bin file call Ultra low function.
> + mdelay(10);

Where did 10 come from? How do you know that is correct?

Same comment for your other delay calls in the driver.

> + return 0;
> +}
> +
> +static int sp_iop_s1mode(struct device *dev, struct sp_iop *iop)
> +{
> + struct regs_iop *p_iop_reg = (struct regs_iop *)iop->iop_regs;
> + int ret, value;
> +
> + ret = readl_poll_timeout(&p_iop_reg->iop_data2, value,
> + (value & IOP_READY) == IOP_READY, 1000, 10000);
> + if (ret) {
> + dev_err(dev, "timed out\n");
> + return ret;
> + }
> +
> + writel(RISC_READY, &p_iop_reg->iop_data2);
> + writel(0x00, &p_iop_reg->iop_data5);
> + writel(0x60, &p_iop_reg->iop_data6);
> +
> + ret = readl_poll_timeout(&p_iop_reg->iop_data7, value,
> + value == 0xaaaa, 1000, 10000);
> + if (ret) {
> + dev_err(dev, "timed out\n");
> + return ret;
> + }
> +
> + writel(0xee, &p_iop_reg->iop_data1);//8051 bin file call S1_mode function.
> + mdelay(10);
> + return 0;
> +}
> +
> +static ssize_t sp_iop_mailbox_show(struct device *dev, struct device_attribute *attr, char *buf)
> +{
> + struct sp_iop *iop = dev_get_drvdata(dev);
> + struct regs_iop *p_iop_reg = (struct regs_iop *)iop->iop_regs;
> + unsigned int mailbox;
> +
> + mailbox = readl(&p_iop_reg->iop_data0);
> + return sysfs_emit(buf, "mailbox = 0x%x\n", mailbox);
> +}
> +
> +static ssize_t sp_iop_mode_show(struct device *dev, struct device_attribute *attr, char *buf)
> +{
> + struct sp_iop *iop = dev_get_drvdata(dev);
> +
> + return sysfs_emit(buf, "bin code mode = 0x%x\n", iop->mode);

That is not a valid sysfs file output. Again "ONE VALUE PER FILE", you
should never have to parse the output like this.

> +}
> +
> +static ssize_t sp_iop_mode_store(struct device *dev, struct device_attribute *attr,
> + const char *buf, size_t count)
> +{
> + struct sp_iop *iop = dev_get_drvdata(dev);
> +
> + if (sysfs_streq(buf, "0"))
> + sp_iop_normal_mode(iop);
> + else if (sysfs_streq(buf, "1"))
> + sp_iop_standby_mode(iop);
> + return count;

So no matter what you write here, it will not return an error?

That is not correct.

> +}
> +
> +static DEVICE_ATTR_RO(sp_iop_mailbox);
> +static DEVICE_ATTR_RW(sp_iop_mode);
> +
> +static int sp_iop_get_normal_code(struct device *dev, struct sp_iop *iop)
> +{
> + const struct firmware *fw;
> + static const char file[] = "normal.bin";
> + unsigned int err, i;
> +
> + err = request_firmware(&fw, file, dev);
> + if (err) {
> + dev_err(dev, "get bin file error\n");
> + return err;
> + }
> +
> + for (i = 0; i < NORMAL_CODE_MAX_SIZE; i++) {
> + char temp;
> +
> + temp = fw->data[i];
> + iop->iop_normal_code[i] = temp;
> + }
> + release_firmware(fw);
> + return err;
> +}
> +
> +static int sp_iop_get_standby_code(struct device *dev, struct sp_iop *iop)
> +{
> + const struct firmware *fw;
> + static const char file[] = "standby.bin";
> + unsigned int err, i;
> +
> + err = request_firmware(&fw, file, dev);
> + if (err) {
> + dev_err(dev, "get bin file error\n");
> + return err;
> + }
> +
> + for (i = 0; i < STANDBY_CODE_MAX_SIZE; i++) {
> + char temp;
> +
> + temp = fw->data[i];
> + iop->iop_standby_code[i] = temp;
> + }
> + release_firmware(fw);
> + return err;
> +}
> +
> +static int sp_iop_get_resources(struct platform_device *pdev, struct sp_iop *p_sp_iop_info)
> +{
> + struct resource *r;
> +
> + r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "iop");
> + p_sp_iop_info->iop_regs = devm_ioremap_resource(&pdev->dev, r);
> + if (IS_ERR(p_sp_iop_info->iop_regs)) {
> + dev_err(&pdev->dev, "ioremap fail\n");
> + return PTR_ERR(p_sp_iop_info->iop_regs);
> + }
> +
> + r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "iop_pmc");
> + p_sp_iop_info->pmc_regs = devm_ioremap_resource(&pdev->dev, r);
> + if (IS_ERR(p_sp_iop_info->pmc_regs)) {
> + dev_err(&pdev->dev, "ioremap fail\n");
> + return PTR_ERR(p_sp_iop_info->pmc_regs);
> + }
> +
> + r = platform_get_resource_byname(pdev, IORESOURCE_MEM, "moon0");
> + p_sp_iop_info->moon0_regs = devm_ioremap_resource(&pdev->dev, r);
> + if (IS_ERR(p_sp_iop_info->moon0_regs)) {
> + dev_err(&pdev->dev, "ioremap fail\n");
> + return PTR_ERR(p_sp_iop_info->moon0_regs);
> + }
> + return IOP_SUCCESS;
> +}
> +
> +static int sp_iop_platform_driver_probe(struct platform_device *pdev)
> +{
> + int ret = -ENXIO;
> + int rc;
> + struct sp_iop *iop;
> + struct device_node *memnp;
> + struct resource mem_res;
> +
> + iop = devm_kzalloc(&pdev->dev, sizeof(struct sp_iop), GFP_KERNEL);
> + if (!iop) {
> + ret = -ENOMEM;
> + goto fail_kmalloc;
> + }
> + /* init */
> + mutex_init(&iop->write_lock);
> + ret = sp_iop_get_resources(pdev, iop);
> +
> + //Get reserve address
> + memnp = of_parse_phandle(pdev->dev.of_node, "memory-region", 0);
> + if (!memnp) {
> + dev_err(&pdev->dev, "no memory-region node\n");
> + return -EINVAL;
> + }
> +
> + rc = of_address_to_resource(memnp, 0, &mem_res);
> + of_node_put(memnp);
> + if (rc) {
> + dev_err(&pdev->dev, "failed to translate memory-region to a resource\n");
> + return -EINVAL;
> + }
> +
> + iop->iop_mem_start = mem_res.start;
> + iop->iop_mem_size = resource_size(&mem_res);
> +
> + ret = sp_iop_get_normal_code(&pdev->dev, iop);
> + if (ret != 0) {
> + dev_err(&pdev->dev, "get normal code err=%d\n", ret);
> + return ret;
> + }
> +
> + ret = sp_iop_get_standby_code(&pdev->dev, iop);
> + if (ret != 0) {
> + dev_err(&pdev->dev, "get standby code err=%d\n", ret);
> + return ret;
> + }
> +
> + sp_iop_normal_mode(iop);
> + platform_set_drvdata(pdev, iop);
> + device_create_file(&pdev->dev, &dev_attr_sp_iop_mailbox);
> + device_create_file(&pdev->dev, &dev_attr_sp_iop_mode);

You just raced with userspace and lost. Set the default groups pointer
of the misc device to your attribute group and then they will be
automatically created for you.




> + iop->gpio_wakeup = of_get_named_gpio(pdev->dev.of_node, "iop-wakeup", 0);
> + return 0;
> +
> +fail_kmalloc:
> + return ret;
> +}
> +
> +static void sp_iop_platform_driver_shutdown(struct platform_device *pdev)
> +{
> + struct sp_iop *iop = platform_get_drvdata(pdev);
> + struct regs_iop *p_iop_reg = (struct regs_iop *)iop->iop_regs;
> + unsigned int value;
> +
> + sp_iop_standby_mode(iop);
> + mdelay(10);

Why sleep on shutdown?

thanks,

greg k-h

\
 
 \ /
  Last update: 2021-12-30 14:13    [W:0.094 / U:0.500 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site