lkml.org 
[lkml]   [2021]   [Dec]   [3]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH] base: arch_topology: Use policy->max to calculate freq_factor
On Thu, Dec 02, 2021 at 05:31:53PM +0100, Rafael J. Wysocki wrote:
> On Thu, Dec 2, 2021 at 11:50 AM Morten Rasmussen
> <morten.rasmussen@arm.com> wrote:
> >
> > On Wed, Nov 17, 2021 at 06:59:05PM +0100, Rafael J. Wysocki wrote:
> > > On Wed, Nov 17, 2021 at 6:01 PM Thara Gopinath
> > > <thara.gopinath@linaro.org> wrote:
> > > >
> > > > Hi,
> > > >
> > > > On 11/17/21 7:49 AM, Rafael J. Wysocki wrote:
> > > > > On Wed, Nov 17, 2021 at 11:46 AM Lukasz Luba <lukasz.luba@arm.com> wrote:
> > > > >>
> > > > >> Hi Rafael,
> > > > >>
> > > > >> On 11/16/21 7:05 PM, Rafael J. Wysocki wrote:
> > > > >>> On Mon, Nov 15, 2021 at 9:10 PM Thara Gopinath
> > > > >>> <thara.gopinath@linaro.org> wrote:
> > > > >>>>
> > > > >>>> cpuinfo.max_freq can reflect boost frequency if enabled during boot. Since
> > > > >>>> we don't consider boost frequencies while calculating cpu capacities, use
> > > > >>>> policy->max to populate the freq_factor during boot up.
> > > > >>>
> > > > >>> I'm not sure about this. schedutil uses cpuinfo.max_freq as the max frequency.
> > > > >>
> > > > >> Agree it's tricky how we treat the boost frequencies and also combine
> > > > >> them with thermal pressure.
> > > > >> We probably would have consider these design bits:
> > > > >> 1. Should thermal pressure include boost frequency?
> > > > >
> > > > > Well, I guess so.
> > > > >
> > > > > Running at a boost frequency certainly increases thermal pressure.
> > > > >
> > > > >> 2. Should max capacity 1024 be a boost frequency so scheduler
> > > > >> would see it explicitly?
> > > > >
> > > > > That's what it is now if cpuinfo.max_freq is a boost frequency.
> > > > >
> > > > >> - if no, then schedutil could still request boost freq thanks to
> > > > >> map_util_perf() where we add 25% to the util and then
> > > > >> map_util_freq() would return a boost freq when util was > 1024
> > > > >>
> > > > >>
> > > > >> I can see in schedutil only one place when cpuinfo.max_freq is used:
> > > > >> get_next_freq(). If the value stored in there is a boost,
> > > > >> then don't we get a higher freq value for the same util?
> > > > >
> > > > > Yes. we do, which basically is my point.
> > > > >
> > > > > The schedutil's response is proportional to cpuinfo.max_freq and that
> > > > > needs to be taken into account for the results to be consistent.
> > > >
> > > > So IIUC, cpuinfo.max_freq is always supposed to be the highest supported
> > > > frequency of a cpu, irrespective of whether boost is enabled or not.
> > > > Where as policy->max is the currently available maximum cpu frequency
> > > > which can be equal to cpuinfo.max_freq or lower (depending on whether
> > > > boost is enabled, whether there is a constraint on policy->max placed by
> > > > thermal etc).
> > >
> > > It may also depend on the limit set by user space.
> > >
> > > > So in this case isn't it better for schedutil to consider
> > > > policy->max instead of cpuinfo.max ?
> > >
> > > Not really.
> > >
> > > In that case setting policy->max to 1/2 of cpuinfo.max_freq would
> > > cause schedutil to choose 1/4 of cpuinfo.max_freq for 50% utilization
> > > which would be rather unexpected.
> > >
> > > policy->max is a cap, not the current maximum capacity.
> > >
> > > > Like you mentioned above same
> > > > utilization will relate to different frequencies depending on the
> > > > maximum frequency.
> > >
> > > Which is not how it is expected (and defined) to work, though.
> > >
> > > If you really want to play with the current maximum capacity, you need
> > > to change it whenever boost is disabled or enabled - and there is a
> > > mechanism for updating cpufinfo.max_freq in such cases.
> >
> > I don't see why we would want to change max capacity on the fly. It is
> > not a cheap operation as we would need to normalize the capacity for all
> > CPUs if the CPU(s) with capacity = 1024 changes its capacity. Worst case
> > we even have to rebuild the sched_domain hierarchy to update flags. The
> > update would also temporarily mess with load and utilization signals, so
> > not a cheap operation.
>
> I didn't say it was cheap. :-)

You didn't :-) But I thought it was worth pointing out in case someone
would think we need to constantly renormalize to the highest achievable
performance level taking all factors into account, including thermal
capping.

> However, boost frequencies are not disabled and enabled very often, so
> it may be acceptable to do it then. I actually don't know.

Agree.

>
> The point is that if you set the max capacity to correspond to the max
> boosted perf and it is never reached (because boost is disabled), the
> scaling will cause CPUs to appear as underutilized, but in fact there
> is no spare capacity in the system.

We kind of have the problem already with thermal capping but addressed
it by having the thermal pressure signal to indicate the some of the
capacity is unavailable. Perhaps the thermal pressure signal should be extended
to cover all reasons for capacity being unavailable, or we should have
another signal to track boost frequencies not being delivered, manually
disabled or not possible due to system circumstances?

> Conversely, if the max capacity corresponds to the max non-boost perf
> and boost is used very often, the scaling will cause the CPUs to
> appear to be 100% loaded, but there may be still spare capacity in the
> system.

It is even worse than that. Allowing delivered performance to exceed the
CPU capacity will break utilization scale invariance at it will make
per-task utilization appear smaller than it really is potentially
leading to wrong task placement.

I think we have to ensure that the full performance range is visible to
the OS. If part of it is often unachievable we need to track the gap
between requested and delivered performance and somehow take that into
account when making task placement decisions.

Morten

\
 
 \ /
  Last update: 2021-12-03 10:49    [W:0.086 / U:0.664 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site