lkml.org 
[lkml]   [2021]   [Dec]   [2]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v6] ARM: dts: aspeed: Adding Facebook Bletchley BMC
Hello Howard,

Please just cc the people that get_maintainers.pl spits out. You don't
want to cc soc@kenrel.org (that's for when patches are ready to apply,
and something that the maintainer for the platform will handle).

$ ./scripts/get_maintainer.pl -f
arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
Rob Herring <robh+dt@kernel.org> (maintainer:OPEN FIRMWARE AND
FLATTENED DEVICE TREE BINDINGS)
Joel Stanley <joel@jms.id.au> (supporter:ARM/ASPEED MACHINE SUPPORT)
Andrew Jeffery <andrew@aj.id.au> (reviewer:ARM/ASPEED MACHINE SUPPORT)
devicetree@vger.kernel.org (open list:OPEN FIRMWARE AND FLATTENED
DEVICE TREE BINDINGS)
linux-arm-kernel@lists.infradead.org (moderated list:ARM/ASPEED MACHINE SUPPORT)
linux-aspeed@lists.ozlabs.org (moderated list:ARM/ASPEED MACHINE SUPPORT)
linux-kernel@vger.kernel.org (open list)


On Wed, 1 Dec 2021 at 03:39, Howard Chiu <howard10703049@gmail.com> wrote:
>
> Initial introduction of Facebook Bletchley equipped with
> Aspeed 2600 BMC SoC.

I like to have some background on the machine, as it provides context
for the review. Is it a x86 server? A x86 switch? Of course if this
information is confidential then that's fine to omit it, only provide
what you can.

>
> Signed-off-by: Howard Chiu <howard.chiu@quantatw.com>
>


Put the changes below under ---. This is so they are not included in
the commit message when added to the kernel.

If the information is relevant, then put it in the commit message
above your s-o-b.

> Change since v5:
> - Add an EEPROM on i2c-7
> - Change address of FUSB302 to 0x22
> - Assign interrupt pin to FUSB302
> - Rework pin assignment of pca9539
>
> Change since v4:
> - Change address of TMP421 on i2c-12 to 0x4d
>
> Change since v3:
> - Add a TMP421 on i2c-10
>
> Change since v2:
> - Remove uart5 workaround
> - Remove gpio nodes of pca9552/pca9539
> - Modify gpio-line-name of led/power/presence pins with openbmc pattern
> - Add MP5023 devices
>
> Change since v1:
> - Keep sorted in Makefile
> - Change baudrate to 57600 from 115200
> - Rename node *-ember to *-amber
> - Use openbmc-flash-layout-128.dtsi
> ---
> arch/arm/boot/dts/Makefile | 1 +
> .../dts/aspeed-bmc-facebook-bletchley.dts | 760 ++++++++++++++++++
> 2 files changed, 761 insertions(+)
> create mode 100644 arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 0de64f237cd8..b804b577010a 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1482,6 +1482,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
> aspeed-bmc-arm-stardragon4800-rep2.dtb \
> aspeed-bmc-asrock-e3c246d4i.dtb \
> aspeed-bmc-bytedance-g220a.dtb \
> + aspeed-bmc-facebook-bletchley.dtb \
> aspeed-bmc-facebook-cloudripper.dtb \
> aspeed-bmc-facebook-cmm.dtb \
> aspeed-bmc-facebook-elbert.dtb \
> diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
> new file mode 100644
> index 000000000000..c013ebe1704a
> --- /dev/null
> +++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
> @@ -0,0 +1,760 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +// Copyright (c) 2021 Facebook Inc.
> +/dts-v1/;
> +
> +#include "aspeed-g6.dtsi"
> +#include <dt-bindings/gpio/aspeed-gpio.h>
> +#include <dt-bindings/usb/pd.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +
> +/ {
> + model = "Facebook Bletchley BMC";
> + compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
> +
> + aliases {
> + serial4 = &uart5;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS4,57600n8";
> + };
> +
> + memory@80000000 {
> + device_type = "memory";
> + reg = <0x80000000 0x80000000>;
> + };
> +
> + iio-hwmon {
> + compatible = "iio-hwmon";
> + io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
> + <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
> + <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
> + <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
> + };
> +
> + spi_gpio: spi-gpio {
> + status = "okay";

The okay is redundant.

> + compatible = "spi-gpio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
> + gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
> + gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
> + num-chipselects = <1>;
> + cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
> +
> + tpmdev@0 {
> + compatible = "tcg,tpm_tis-spi";
> + spi-max-frequency = <33000000>;
> + reg = <0>;
> + };
> + };
> +
> + switchphy: ethernet-phy@0 {
> + // Fixed-link

Are there any properties we should be adding here? Other examples
mention the speed and duplex setting.

> + };
> +

> +
> +&i2c0 {

> +
> + sled0_fusb302: typec-portc@54 {
> + compatible = "fcs,fusb302";
> + reg = <0x22>;

Your reg property is 22, but the unit address is 54. These need to
math or you will get a warning from the device tree compiler:

arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts:254.32-271.4:
Warning (i2c_bus_reg):
/ahb/apb/bus@1e78a000/i2c-bus@80/typec-portc@54: I2C bus unit address
format error, expected "22"

Please fix this for all the fusb302 nodes, and make sure you build
test with this patch applied to v5.16-rc1, or newer.

../arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts:254.32-271.4:
Warning (i2c_bus_reg):
/ahb/apb/bus@1e78a000/i2c-bus@80/typec-portc@54: I2C bus unit address
format error, expected "22"
../arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts:318.32-335.4:
Warning (i2c_bus_reg):
/ahb/apb/bus@1e78a000/i2c-bus@100/typec-portc@54: I2C bus unit address
format error, expected "22"
../arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts:386.32-404.4:
Warning (i2c_bus_reg):
/ahb/apb/bus@1e78a000/i2c-bus@180/typec-portc@54: I2C bus unit address
format error, expected "22"
../arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts:451.32-469.4:
Warning (i2c_bus_reg):
/ahb/apb/bus@1e78a000/i2c-bus@200/typec-portc@54: I2C bus unit address
format error, expected "22"
../arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts:516.32-533.4:
Warning (i2c_bus_reg):
/ahb/apb/bus@1e78a000/i2c-bus@280/typec-portc@54: I2C bus unit address
format error, expected "22"
../arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts:580.32-597.4:
Warning (i2c_bus_reg):
/ahb/apb/bus@1e78a000/i2c-bus@300/typec-portc@54: I2C bus unit address
format error, expected "22"


> + interrupt-parent = <&gpio0>;
> + interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
> +
> + connector {
> + compatible = "usb-c-connector";
> + label = "USB-C";
> + power-role = "dual";
> + try-power-role = "sink";
> + source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> + sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> + PDO_VAR(3000, 12000, 3000)
> + PDO_PPS_APDO(3000, 11000, 3000)>;
> + op-sink-microwatt = <10000000>;
> + };
> + };
> +};
> +

Cheers,

Joel

\
 
 \ /
  Last update: 2021-12-02 07:08    [W:0.099 / U:0.148 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site