lkml.org 
[lkml]   [2021]   [Dec]   [17]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2 2/2] mtd: spi-nor: macronix: Add support for mx66lm1g45g
Date
mx66lm1g45g supports just 1-1-1, 8-8-8 and 8d-8d-8d modes. There are
versions of mx66lm1g45g which do not support SFDP, thus use
SPI_NOR_SKIP_SFDP. The RDID command issued through the octal peripheral
interface outputs data always in STR mode for whatever reason. Since
8d-8d-8s is not common, avoid reading the ID when enabling the octal dtr
mode. Instead, read back the CR2 to check if the switch was successful.
Tested in 1-1-1 and 8d-8d-8d modes using sama7g5 QSPI IP.

Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
---
v2:
- drop setting of dummy cycles, use the default value
- avoid odd lengths in octal dtr mode
- s/8d-8d-8d/8D-8D-8D

# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/jedec_id
c2853b
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/manufacturer
macronix
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/partname
mx66lm1g45g
# cat /sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/sfdp
cat: can't open '/sys/devices/platform/soc/e080c000.spi/spi_master/spi1/spi1.0/spi-nor/sfdp': No such file or directory

drivers/mtd/spi-nor/macronix.c | 96 ++++++++++++++++++++++++++++++++++
1 file changed, 96 insertions(+)

diff --git a/drivers/mtd/spi-nor/macronix.c b/drivers/mtd/spi-nor/macronix.c
index 67aaa83038b6..4c672deb1d1c 100644
--- a/drivers/mtd/spi-nor/macronix.c
+++ b/drivers/mtd/spi-nor/macronix.c
@@ -32,6 +32,95 @@ static struct spi_nor_fixups mx25l25635_fixups = {
.post_bfpt = mx25l25635_post_bfpt_fixups,
};

+#define SPINOR_OP_READ_CR2 0x71
+#define SPINOR_OP_WRITE_CR2 0x72
+#define SPINOR_OP_MX_DTR_RD 0xee
+
+#define SPINOR_REG_CR2_MODE_ADDR 0
+#define SPINOR_REG_CR2_DTR_OPI_ENABLE BIT(1)
+#define SPINOR_REG_CR2_SPI 0
+
+static int spi_nor_macronix_octal_dtr_enable(struct spi_nor *nor, bool enable)
+{
+ u8 *buf = nor->bouncebuf;
+ struct spi_mem_op op;
+ int ret;
+
+ /* Set/unset the octal and DTR enable bits. */
+ if (enable) {
+ buf[0] = SPINOR_REG_CR2_DTR_OPI_ENABLE;
+ } else {
+ /*
+ * The register is one byte wide, but the one byte transactions
+ * are not allowed in 8D-8D-8D mode. Since there is no register
+ * at the next location, just initialize the value to zero and
+ * let the transaction go on.
+ */
+ buf[0] = SPINOR_REG_CR2_SPI;
+ buf[1] = 0;
+ }
+
+ op = (struct spi_mem_op)
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_WRITE_CR2, 1),
+ SPI_MEM_OP_ADDR(4, SPINOR_REG_CR2_MODE_ADDR, 1),
+ SPI_MEM_OP_NO_DUMMY,
+ SPI_MEM_OP_DATA_OUT(enable ? 1 : 2, buf, 1));
+ if (!enable)
+ spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+ ret = spi_nor_write_enable(nor);
+ if (ret)
+ return ret;
+
+ ret = spi_mem_exec_op(nor->spimem, &op);
+ if (ret)
+ return ret;
+
+ /* Read back CR2 to make sure the switch was successful. */
+ op = (struct spi_mem_op)
+ SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_READ_CR2, 1),
+ SPI_MEM_OP_ADDR(4, SPINOR_REG_CR2_MODE_ADDR, 1),
+ SPI_MEM_OP_DUMMY(enable ? 4 : 0, 1),
+ SPI_MEM_OP_DATA_IN(enable ? 2 : 1, buf, 1));
+ if (enable)
+ spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+
+ ret = spi_mem_exec_op(nor->spimem, &op);
+ if (ret)
+ return ret;
+
+ if (enable) {
+ if (buf[0] != SPINOR_REG_CR2_DTR_OPI_ENABLE) {
+ dev_dbg(nor->dev, "Failed to enable 8D-8D-8D mode.\n");
+ return -EINVAL;
+ }
+ } else if (buf[0] != SPINOR_REG_CR2_SPI) {
+ dev_dbg(nor->dev, "Failed to disable 8D-8D-8D mode.\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void mx66lm1g45g_late_init(struct spi_nor *nor)
+{
+ nor->params->octal_dtr_enable = spi_nor_macronix_octal_dtr_enable;
+
+ /* Set the Fast Read settings. */
+ nor->params->hwcaps.mask |= SNOR_HWCAPS_READ_8_8_8_DTR;
+ spi_nor_set_read_settings(&nor->params->reads[SNOR_CMD_READ_8_8_8_DTR],
+ 0, 20, SPINOR_OP_MX_DTR_RD,
+ SNOR_PROTO_8_8_8_DTR);
+
+ nor->cmd_ext_type = SPI_NOR_EXT_INVERT;
+ nor->params->rdsr_dummy = 4;
+ nor->params->rdsr_addr_nbytes = 4;
+}
+
+static struct spi_nor_fixups mx66lm1g45g_fixups = {
+ .late_init = mx66lm1g45g_late_init,
+};
+
static const struct flash_info macronix_parts[] = {
/* Macronix */
{ "mx25l512e", INFO(0xc22010, 0, 64 * 1024, 1)
@@ -100,6 +189,13 @@ static const struct flash_info macronix_parts[] = {
{ "mx66u2g45g", INFO(0xc2253c, 0, 64 * 1024, 4096)
NO_SFDP_FLAGS(SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ)
FIXUP_FLAGS(SPI_NOR_4B_OPCODES) },
+ { "mx66lm1g45g", INFO(0xc2853b, 0, 64 * 1024, 2048)
+ NO_SFDP_FLAGS(SPI_NOR_SKIP_SFDP | SECT_4K |
+ SPI_NOR_OCTAL_DTR_READ | SPI_NOR_OCTAL_DTR_PP)
+ FIXUP_FLAGS(SPI_NOR_4B_OPCODES | SPI_NOR_IO_MODE_EN_VOLATILE |
+ SPI_NOR_SOFT_RESET)
+ .fixups = &mx66lm1g45g_fixups,
+ },
};

static void macronix_default_init(struct spi_nor *nor)
--
2.25.1
\
 
 \ /
  Last update: 2021-12-17 14:43    [W:0.706 / U:0.584 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site