lkml.org 
[lkml]   [2021]   [Dec]   [16]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH] clk: qcom: rcg2: Cache rate changes for parked RCGs
From
Date
Quoting Bjorn Andersson (2021-12-16 15:32:32)
> On Thu 16 Dec 10:58 PST 2021, Stephen Boyd wrote:
>
> > Quoting Bjorn Andersson (2021-12-15 18:48:27)
> > > On Wed 15 Dec 17:51 PST 2021, Stephen Boyd wrote:
> > >
> > > > Quoting Bjorn Andersson (2021-12-02 19:56:01)
> > > > > As GDSCs are turned on and off some associated clocks are momentarily
> > > > > enabled for house keeping purposes. Failure to enable these clocks seems
> > > > > to have been silently ignored in the past, but starting in SM8350 this
> > > > > failure will prevent the GDSC to turn on.
> > > > >
> > > > > At least on SM8350 this operation will enable the RCG per the
> > > > > configuration in CFG_REG. This means that the current model where the
> > > > > current configuration is written back to CF_REG immediately after
> > > > > parking the RCG doesn't work.
> > > >
> > > > Just to clarify, is the RCG off and "parked" at XO with the config
> > > > register dirty and set to the desired frequency and then the RCG is
> > > > turned on by the GDSC?
> > > >
> > >
> > > Correct, that's exactly what I'm observing.
> >
> > Cool can you add that detail to the commit message?
> >
>
> Sure.
>
> > >
> > > > >
> > > > > Instead, keep track of the currently requested rate of the clock and
> > > > > upon enabling the clock reapply the configuration per the saved rate.
> > > >
> > > > We already keep track of the requested rate and reapply it on enable,
> > > > just we're lazy and stash that information in the hardware and not the
> > > > software. I didn't think the gdsc would be turned on and ruin that all,
> > > > but it's fair.
> > > >
> > >
> > > Up until SM8350 I see no evidence that this has been a problem, but now
> > > it is. So there's likely some changes in the hardware there...
> > >
> > > > >
> > > > > Fixes: 7ef6f11887bd ("clk: qcom: Configure the RCGs to a safe source as needed")
> > > > > Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> > > > > ---
> > > > > drivers/clk/qcom/clk-rcg.h | 2 ++
> > > > > drivers/clk/qcom/clk-rcg2.c | 32 +++++++++++++++++---------------
> > > > > 2 files changed, 19 insertions(+), 15 deletions(-)
> > > > >
> > > > > diff --git a/drivers/clk/qcom/clk-rcg.h b/drivers/clk/qcom/clk-rcg.h
> > > > > index 99efcc7f8d88..6939f4e62768 100644
> > > > > --- a/drivers/clk/qcom/clk-rcg.h
> > > > > +++ b/drivers/clk/qcom/clk-rcg.h
> > > > > @@ -139,6 +139,7 @@ extern const struct clk_ops clk_dyn_rcg_ops;
> > > > > * @freq_tbl: frequency table
> > > > > * @clkr: regmap clock handle
> > > > > * @cfg_off: defines the cfg register offset from the CMD_RCGR + CFG_REG
> > > > > + * @current_rate: cached rate for parked RCGs
> > > > > */
> > > > > struct clk_rcg2 {
> > > > > u32 cmd_rcgr;
> > > > > @@ -149,6 +150,7 @@ struct clk_rcg2 {
> > > > > const struct freq_tbl *freq_tbl;
> > > > > struct clk_regmap clkr;
> > > > > u8 cfg_off;
> > > > > + unsigned long current_rate;
> > > > > };
> > > > >
> > > > > #define to_clk_rcg2(_hw) container_of(to_clk_regmap(_hw), struct clk_rcg2, clkr)
> > > > > diff --git a/drivers/clk/qcom/clk-rcg2.c b/drivers/clk/qcom/clk-rcg2.c
> > > > > index e1b1b426fae4..b574b38dcbd5 100644
> > > > > --- a/drivers/clk/qcom/clk-rcg2.c
> > > > > +++ b/drivers/clk/qcom/clk-rcg2.c
> > > > > @@ -167,6 +167,7 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
> > > > > {
> > > > > struct clk_rcg2 *rcg = to_clk_rcg2(hw);
> > > > > u32 cfg, hid_div, m = 0, n = 0, mode = 0, mask;
> > > > > + unsigned long rate;
> > > > >
> > > > > regmap_read(rcg->clkr.regmap, RCG_CFG_OFFSET(rcg), &cfg);
> > > > >
> > > > > @@ -186,7 +187,11 @@ clk_rcg2_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
> > > > > hid_div = cfg >> CFG_SRC_DIV_SHIFT;
> > > > > hid_div &= mask;
> > > > >
> > > > > - return calc_rate(parent_rate, m, n, mode, hid_div);
> > > > > + rate = calc_rate(parent_rate, m, n, mode, hid_div);
> > > > > + if (!rcg->current_rate)
> > > > > + rcg->current_rate = rate;
> > > >
> > > > Instead of doing this in recalc_rate, all the time, why not make an init
> > > > clk op that does it once during registration? The other problem I see is
> > > > that the rate we calculate may be wrong if the parent is registered
> > > > after this clk. I think this came up originally when the patch this is
> > > > fixing was discussed.
> > > >
> > >
> > > I would need to go back and reproduce the issue I saw, but I had to add
> > > this because I ended up in clk_rcg2_shared_enable() with current_rate =
> > > 0, which I think would be equally bad to just committing the dirty
> > > configuration.
> >
> > Alright.
> >
> > >
> > > > So instead of saving the current_rate can we save the cfg register value
> > > > (or however many registers we need) to put back the frequency of the clk
> > > > to what we want on enable? The other thing is that we made recalc_rate()
> > > > work "seamlessly" here by stashing the frequency into the register but
> > > > leaving it uncommitted until enable. We may need to now look at the
> > > > software copy of the registers in the shared rcg recalc rate operation
> > > > to figure out what the frequency is.
> > > >
> > >
> > > I made an attempt at this, the problem I had was to come up within
> > > something sane for how to deal with set_rate on parked clocks; because
> > > we need to re-generate the register contents, without writing out the
> > > value - and that got messy.
> >
> > Looking back on the introduction of this code[1] I see that it's not
> > about the rate but more about the parent. i.e. we park the clk on the XO
> > parent but don't care about the m/n values or pre divider because it
> > doesn't really matter if the clk is running slowly. So nothing needs to
> > be saved except for the cfg register, and we can do that in software
> > with a single u32 instead of using a rate and looking it up and then
> > reprogramming the other values. We should be able to cache the register
> > content with an init clk_op.
> >
>
> So you're suggesting that, in clk_rcg2_shared_set_rate(), when the RCG
> is found to be disabled, I should write out M, N, D and calculate a new
> cfg value which I stash until the next enable?
>
> Looks a little bit messy, but I will give it a try.

No. I don't see where clk_rcg2_shared_set_rate() needs to change.

I'm suggesting we cache the config register on disable so it can be
restored on enable. Basically everything is the same except now we don't
write the cfg register and leave it dirty in the hardware. We need a
shared rcg version of recalc rate that looks at the shadow cfg register
instead of reading the hardware because we've changed the parent behind
the back of the framework and we want to make it look like nothing has
changed.

This is all based on my understanding that the problem is the RCG is
changing rate due to the gdsc turning on the clk for us. So we can't
leave anything dirty in the hardware and have to keep it in software.
I hope the change is minimal.

\
 
 \ /
  Last update: 2021-12-17 02:46    [W:0.067 / U:2.088 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site