lkml.org 
[lkml]   [2021]   [Dec]   [15]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v2] usb: hub: Add delay for SuperSpeed hub resume to let links transit to U0
Date
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1

USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.

So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
---
v2:
- Add a small delay instead of waking up all hubs.

drivers/usb/core/hub.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
index 00070a8a65079..576fdf2c9f3c8 100644
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1110,7 +1110,10 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
} else {
hub_power_on(hub, true);
}
- }
+ /* Give some time on remote wakeup to let links to transit to U0 */
+ } else if (hub_is_superspeed(hub->hdev))
+ msleep(20);
+
init2:

/*
--
2.33.1
\
 
 \ /
  Last update: 2021-12-15 13:03    [W:0.069 / U:0.024 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site