lkml.org 
[lkml]   [2021]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
SubjectRe: [PATCH v12, 06/19] media: mtk-vcodec: Add to support multi hardware decode
From
Date
Hi Steve,

Thanks for your suggestion,
On Thu, 2021-12-09 at 15:29 -0800, Steve Cho wrote:
> Few comments and questions.
>
> On Wed, Dec 1, 2021 at 7:46 PM Yunfei Dong <yunfei.dong@mediatek.com>
> wrote:
> >
> > There are more than two hardwares for decoder: LAT0, LAT1 and CORE.
> > In order to
> > manage these hardwares, register each hardware as independent
> > platform device
> > for the larbs are different.
>
> basic question: what is "larbs"?
>
Can regard larbs as some hardware which decode depends on.
> >
> > Each hardware module controls its own information which includes
> > interrupt/power/
> > clocks/registers.
> >
> > Calling of_platform_populate in parent device, and use
> > subdev_bitmap to record
> > whether the hardwares are registered done.
>
> nit: s/registered done/registered/ ?
>
Fix in v13.
> >
> > Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
> > ---
> > drivers/media/platform/mtk-vcodec/Makefile | 5 +-
> > .../platform/mtk-vcodec/mtk_vcodec_dec_drv.c | 111 +++++++----
> > .../platform/mtk-vcodec/mtk_vcodec_dec_hw.c | 172
> > ++++++++++++++++++
> > .../platform/mtk-vcodec/mtk_vcodec_dec_hw.h | 51 ++++++
> > .../mtk-vcodec/mtk_vcodec_dec_stateful.c | 1 +
> > .../mtk-vcodec/mtk_vcodec_dec_stateless.c | 2 +
> > .../platform/mtk-vcodec/mtk_vcodec_drv.h | 19 ++
> > 7 files changed, 329 insertions(+), 32 deletions(-)
> > create mode 100644 drivers/media/platform/mtk-
> > vcodec/mtk_vcodec_dec_hw.c
> > create mode 100644 drivers/media/platform/mtk-
> > vcodec/mtk_vcodec_dec_hw.h
> >
> > diff --git a/drivers/media/platform/mtk-vcodec/Makefile
> > b/drivers/media/platform/mtk-vcodec/Makefile
> > index ca8e9e7a9c4e..c61bfb179bcc 100644
> > --- a/drivers/media/platform/mtk-vcodec/Makefile
> > +++ b/drivers/media/platform/mtk-vcodec/Makefile
> > @@ -2,7 +2,8 @@
> >
> > obj-$(CONFIG_VIDEO_MEDIATEK_VCODEC) += mtk-vcodec-dec.o \
> > mtk-vcodec-enc.o \
> > - mtk-vcodec-common.o
> > + mtk-vcodec-common.o \
> > + mtk-vcodec-dec-hw.o
> >
> > mtk-vcodec-dec-y := vdec/vdec_h264_if.o \
> > vdec/vdec_vp8_if.o \
> > @@ -16,6 +17,8 @@ mtk-vcodec-dec-y := vdec/vdec_h264_if.o \
> > mtk_vcodec_dec_stateless.o \
> > mtk_vcodec_dec_pm.o \
> >
> > +mtk-vcodec-dec-hw-y := mtk_vcodec_dec_hw.o
> > +
> > mtk-vcodec-enc-y := venc/venc_vp8_if.o \
> > venc/venc_h264_if.o \
> > mtk_vcodec_enc.o \
> > diff --git a/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_drv.c
> > b/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_drv.c
> > index b7a51e96d4ba..95fbe9be3f6d 100644
> > --- a/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_drv.c
> > +++ b/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_drv.c
> > @@ -18,19 +18,40 @@
> >
> > #include "mtk_vcodec_drv.h"
> > #include "mtk_vcodec_dec.h"
> > +#include "mtk_vcodec_dec_hw.h"
> > #include "mtk_vcodec_dec_pm.h"
> > #include "mtk_vcodec_intr.h"
> > #include "mtk_vcodec_util.h"
> > #include "mtk_vcodec_fw.h"
> >
> > -#define VDEC_HW_ACTIVE 0x10
> > -#define VDEC_IRQ_CFG 0x11
> > -#define VDEC_IRQ_CLR 0x10
> > -#define VDEC_IRQ_CFG_REG 0xa4
> > -
> > module_param(mtk_v4l2_dbg_level, int, 0644);
> > module_param(mtk_vcodec_dbg, bool, 0644);
> >
> > +static int mtk_vcodec_subdev_device_check(struct mtk_vcodec_dev
> > *vdec_dev)
> > +{
> > + struct platform_device *pdev = vdec_dev->plat_dev;
> > + struct device_node *subdev_node;
> > + enum mtk_vdec_hw_id hw_idx;
> > + const struct of_device_id *of_id;
> > + int i;
> > +
> > + for (i = 0; i < ARRAY_SIZE(mtk_vdec_hw_match); i++) {
> > + of_id = &mtk_vdec_hw_match[i];
> > + subdev_node = of_find_compatible_node(NULL, NULL,
> > + of_id->compatible);
> > + if (!subdev_node)
> > + continue;
> > +
> > + hw_idx = (enum mtk_vdec_hw_id)(uintptr_t)of_id-
> > >data;
> > + if (!test_bit(hw_idx, vdec_dev->subdev_bitmap)) {
> > + dev_err(&pdev->dev, "Vdec %d is not ready",
> > hw_idx);
> > + return -EAGAIN;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > static irqreturn_t mtk_vcodec_dec_irq_handler(int irq, void *priv)
> > {
> > struct mtk_vcodec_dev *dev = priv;
> > @@ -95,6 +116,42 @@ static int mtk_vcodec_get_reg_bases(struct
> > mtk_vcodec_dev *dev)
> > return 0;
> > }
> >
> > +static int mtk_vcodec_init_dec_resources(struct mtk_vcodec_dev
> > *dev)
> > +{
> > + struct platform_device *pdev = dev->plat_dev;
> > + int ret;
> > +
> > + ret = mtk_vcodec_get_reg_bases(dev);
> > + if (ret)
> > + return ret;
> > +
> > + if (dev->vdec_pdata->is_subdev_supported)
> > + return 0;
> > +
> > + dev->dec_irq = platform_get_irq(pdev, 0);
> > + if (dev->dec_irq < 0) {
> > + dev_err(&pdev->dev, "failed to get irq number");
> > + return dev->dec_irq;
> > + }
> > +
> > + irq_set_status_flags(dev->dec_irq, IRQ_NOAUTOEN);
> > + ret = devm_request_irq(&pdev->dev, dev->dec_irq,
> > + mtk_vcodec_dec_irq_handler, 0, pdev->name, dev);
> > + if (ret) {
> > + dev_err(&pdev->dev, "failed to install dev->dec_irq
> > %d (%d)",
> > + dev->dec_irq, ret);
> > + return ret;
> > + }
> > +
> > + ret = mtk_vcodec_init_dec_pm(pdev, &dev->pm);
> > + if (ret < 0) {
> > + dev_err(&pdev->dev, "failed to get mt vcodec clock
> > source");
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > static int fops_vcodec_open(struct file *file)
> > {
> > struct mtk_vcodec_dev *dev = video_drvdata(file);
> > @@ -116,6 +173,12 @@ static int fops_vcodec_open(struct file *file)
> > init_waitqueue_head(&ctx->queue);
> > mutex_init(&ctx->lock);
> >
> > + ret = mtk_vcodec_subdev_device_check(dev);
> > + if (ret) {
> > + mtk_v4l2_err("Failed to check vdec comp device.");
>
> basic question: what is "comp" device?
>
This line can be removed, "comp" is subdev.
> > + goto err_ctrls_setup;
> > + }
> > +
> > ctx->type = MTK_INST_DECODER;
> > ret = dev->vdec_pdata->ctrls_setup(ctx);
> > if (ret) {
> > @@ -220,7 +283,6 @@ static int mtk_vcodec_probe(struct
> > platform_device *pdev)
> > {
> > struct mtk_vcodec_dev *dev;
> > struct video_device *vfd_dec;
> > - struct resource *res;
> > phandle rproc_phandle;
> > enum mtk_vcodec_fw_type fw_type;
> > int ret;
> > @@ -249,32 +311,10 @@ static int mtk_vcodec_probe(struct
> > platform_device *pdev)
> > if (IS_ERR(dev->fw_handler))
> > return PTR_ERR(dev->fw_handler);
> >
> > - ret = mtk_vcodec_init_dec_pm(dev->plat_dev, &dev->pm);
> > - if (ret < 0) {
> > - dev_err(&pdev->dev, "Failed to get mt vcodec clock
> > source");
> > - goto err_dec_pm;
> > - }
> > -
> > - ret = mtk_vcodec_get_reg_bases(dev);
> > - if (ret)
> > - goto err_res;
> > -
> > - res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
> > - if (res == NULL) {
> > - dev_err(&pdev->dev, "failed to get irq resource");
> > - ret = -ENOENT;
> > - goto err_res;
> > - }
> > -
> > - dev->dec_irq = platform_get_irq(pdev, 0);
> > - irq_set_status_flags(dev->dec_irq, IRQ_NOAUTOEN);
> > - ret = devm_request_irq(&pdev->dev, dev->dec_irq,
> > - mtk_vcodec_dec_irq_handler, 0, pdev->name,
> > dev);
> > + ret = mtk_vcodec_init_dec_resources(dev);
> > if (ret) {
> > - dev_err(&pdev->dev, "Failed to install dev->dec_irq
> > %d (%d)",
> > - dev->dec_irq,
> > - ret);
> > - goto err_res;
> > + dev_err(&pdev->dev, "Failed to init dec
> > resources");
> > + goto err_dec_pm;
> > }
> >
> > mutex_init(&dev->dec_mutex);
> > @@ -329,6 +369,15 @@ static int mtk_vcodec_probe(struct
> > platform_device *pdev)
> > goto err_event_workq;
> > }
> >
> > + if (dev->vdec_pdata->is_subdev_supported) {
> > + ret = of_platform_populate(pdev->dev.of_node, NULL,
> > NULL,
> > + &pdev->dev);
> > + if (ret) {
> > + mtk_v4l2_err("Main device
> > of_platform_populate failed.");
> > + goto err_event_workq;
> > + }
> > + }
> > +
> > if (dev->vdec_pdata->uses_stateless_api) {
> > dev->mdev_dec.dev = &pdev->dev;
> > strscpy(dev->mdev_dec.model, MTK_VCODEC_DEC_NAME,
> > diff --git a/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_hw.c
> > b/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_hw.c
> > new file mode 100644
> > index 000000000000..025a103008ba
> > --- /dev/null
> > +++ b/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_hw.c
> > @@ -0,0 +1,172 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (c) 2021 MediaTek Inc.
> > + * Author: Yunfei Dong <yunfei.dong@mediatek.com>
> > + */
> > +
> > +#include <linux/interrupt.h>
> > +#include <linux/irq.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/slab.h>
> > +
> > +#include "mtk_vcodec_drv.h"
> > +#include "mtk_vcodec_dec.h"
> > +#include "mtk_vcodec_dec_hw.h"
> > +#include "mtk_vcodec_dec_pm.h"
> > +#include "mtk_vcodec_intr.h"
> > +#include "mtk_vcodec_util.h"
> > +
> > +const struct of_device_id mtk_vdec_hw_match[] = {
> > + {
> > + .compatible = "mediatek,mtk-vcodec-lat",
> > + .data = (void *)MTK_VDEC_LAT0,
> > + },
>
> Are we supposed to have LAT1 here as well?
At current period, need not to add it. LAT1 may be used in the future.
>
> > + {
> > + .compatible = "mediatek,mtk-vcodec-core",
> > + .data = (void *)MTK_VDEC_CORE,
> > + },
> > + {},
> > +};
> > +EXPORT_SYMBOL_GPL(mtk_vdec_hw_match);
> > +
> > +MODULE_DEVICE_TABLE(of, mtk_vdec_hw_match);
> > +
> > +static irqreturn_t mtk_vdec_hw_irq_handler(int irq, void *priv)
> > +{
> > + struct mtk_vdec_hw_dev *dev = priv;
> > + struct mtk_vcodec_ctx *ctx;
> > + u32 cg_status;
> > + unsigned int dec_done_status;
> > + void __iomem *vdec_misc_addr = dev->reg_base[VDEC_HW_MISC]
> > +
> > + VDEC_IRQ_CFG_REG;
> > +
> > + ctx = mtk_vcodec_get_curr_ctx(dev->main_dev);
> > +
> > + /* check if HW active or not */
> > + cg_status = readl(dev->reg_base[VDEC_HW_SYS]);
> > + if (cg_status & VDEC_HW_ACTIVE) {
> > + mtk_v4l2_err("vdec active is not 0x0 (0x%08x)",
> > + cg_status);
> > + return IRQ_HANDLED;
> > + }
> > +
> > + dec_done_status = readl(vdec_misc_addr);
> > + if ((dec_done_status & MTK_VDEC_IRQ_STATUS_DEC_SUCCESS) !=
> > + MTK_VDEC_IRQ_STATUS_DEC_SUCCESS)
> > + return IRQ_HANDLED;
> > +
> > + /* clear interrupt */
> > + writel(dec_done_status | VDEC_IRQ_CFG, vdec_misc_addr);
>
> Is VDEC_IRQ_CFG also intended for clear interrupt?
>
VDEC_IRQ_CFG and VDEC_IRQ_CLR are different bits to clear interrupt.
> > + writel(dec_done_status & ~VDEC_IRQ_CLR, vdec_misc_addr);
> > +
> > + wake_up_ctx(ctx, MTK_INST_IRQ_RECEIVED);
> > +
> > + mtk_v4l2_debug(3, "wake up ctx %d, dec_done_status=%x",
> > + ctx->id, dec_done_status);
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +static int mtk_vdec_hw_init_irq(struct mtk_vdec_hw_dev *dev)
> > +{
> > + struct platform_device *pdev = dev->plat_dev;
> > + int ret;
> > +
> > + dev->dec_irq = platform_get_irq(pdev, 0);
> > + if (dev->dec_irq < 0) {
> > + dev_err(&pdev->dev, "Failed to get irq resource");
> > + return dev->dec_irq;
> > + }
> > +
> > + irq_set_status_flags(dev->dec_irq, IRQ_NOAUTOEN);
> > + ret = devm_request_irq(&pdev->dev, dev->dec_irq,
> > + mtk_vdec_hw_irq_handler, 0, pdev-
> > >name, dev);
> > + if (ret) {
> > + dev_err(&pdev->dev, "Failed to install dev->dec_irq
> > %d (%d)",
> > + dev->dec_irq, ret);
> > + return ret;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int mtk_vdec_hw_probe(struct platform_device *pdev)
> > +{
> > + struct device *dev = &pdev->dev;
> > + struct mtk_vdec_hw_dev *subdev_dev;
> > + struct mtk_vcodec_dev *main_dev;
> > + const struct of_device_id *of_id;
> > + int hw_idx;
> > + int ret;
> > +
> > + if (!dev->parent) {
> > + dev_err(dev, "no parent for hardware devices.\n");
> > + return -ENODEV;
> > + }
> > +
> > + main_dev = dev_get_drvdata(dev->parent);
> > + if (!main_dev) {
> > + dev_err(dev, "failed to get parent driver data");
> > + return -EINVAL;
> > + }
> > +
> > + subdev_dev = devm_kzalloc(dev, sizeof(*subdev_dev),
> > GFP_KERNEL);
> > + if (!subdev_dev)
> > + return -ENOMEM;
> > +
> > + subdev_dev->plat_dev = pdev;
> > + ret = mtk_vcodec_init_dec_pm(pdev, &subdev_dev->pm);
> > + if (ret)
> > + return ret;
> > +
> > + subdev_dev->reg_base[VDEC_HW_MISC] =
> > + devm_platform_ioremap_resource(pdev, 0);
> > + if (IS_ERR((__force void *)subdev_dev-
> > >reg_base[VDEC_HW_MISC])) {
> > + ret = PTR_ERR((__force void *)subdev_dev-
> > >reg_base[VDEC_HW_MISC]);
> > + goto err;
> > + }
> > +
> > + ret = mtk_vdec_hw_init_irq(subdev_dev);
> > + if (ret)
> > + goto err;
> > +
> > + of_id = of_match_device(mtk_vdec_hw_match, dev);
> > + if (!of_id) {
> > + dev_err(dev, "Can't get vdec subdev id.\n");
> > + ret = -EINVAL;
> > + goto err;
> > + }
> > +
> > + hw_idx = (enum mtk_vdec_hw_id)(uintptr_t)of_id->data;
> > + if (hw_idx >= MTK_VDEC_HW_MAX) {
> > + dev_err(dev, "Hardware index %d not correct.\n",
> > hw_idx);
> > + ret = -EINVAL;
> > + goto err;
> > + }
> > +
> > + main_dev->subdev_dev[hw_idx] = subdev_dev;
> > + subdev_dev->hw_idx = hw_idx;
> > + subdev_dev->main_dev = main_dev;
> > + subdev_dev->reg_base[VDEC_HW_SYS] = main_dev-
> > >reg_base[VDEC_HW_SYS];
> > + set_bit(subdev_dev->hw_idx, main_dev->subdev_bitmap);
> > +
> > + platform_set_drvdata(pdev, subdev_dev);
> > + return 0;
> > +err:
> > + mtk_vcodec_release_dec_pm(&subdev_dev->pm);
> > + return ret;
> > +}
> > +
> > +static struct platform_driver mtk_vdec_driver = {
> > + .probe = mtk_vdec_hw_probe,
> > + .driver = {
> > + .name = "mtk-vdec-comp",
> > + .of_match_table = mtk_vdec_hw_match,
> > + },
> > +};
> > +module_platform_driver(mtk_vdec_driver);
> > +
> > +MODULE_LICENSE("GPL v2");
> > +MODULE_DESCRIPTION("Mediatek video decoder hardware driver");
> > diff --git a/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_hw.h
> > b/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_hw.h
> > new file mode 100644
> > index 000000000000..f7f36790629d
> > --- /dev/null
> > +++ b/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_hw.h
> > @@ -0,0 +1,51 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * Copyright (c) 2021 MediaTek Inc.
> > + * Author: Yunfei Dong <yunfei.dong@mediatek.com>
> > + */
> > +
> > +#ifndef _MTK_VCODEC_DEC_HW_H_
> > +#define _MTK_VCODEC_DEC_HW_H_
> > +
> > +#include <linux/io.h>
> > +#include <linux/platform_device.h>
> > +
> > +#include "mtk_vcodec_drv.h"
> > +
> > +#define VDEC_HW_ACTIVE 0x10
> > +#define VDEC_IRQ_CFG 0x11
> > +#define VDEC_IRQ_CLR 0x10
> > +#define VDEC_IRQ_CFG_REG 0xa4
> > +
> > +extern const struct of_device_id
> > mtk_vdec_hw_match[MTK_VDEC_HW_MAX];
> > +
> > +/**
> > + * enum mtk_vdec_hw_reg_idx - subdev hardware register base index
> > + */
> > +enum mtk_vdec_hw_reg_idx {
> > + VDEC_HW_SYS,
> > + VDEC_HW_MISC,
> > + VDEC_HW_MAX
> > +};
> > +
> > +/**
> > + * struct mtk_vdec_hw_dev - vdec hardware driver data
> > + * @plat_dev: platform device
> > + * @main_dev: main device
> > + * @reg_base: Mapped address of MTK Vcodec registers.
> > + *
> > + * @dec_irq: decoder irq resource
> > + * @pm: power management control
> > + * @hw_idx: each hardware index
> > + */
> > +struct mtk_vdec_hw_dev {
> > + struct platform_device *plat_dev;
> > + struct mtk_vcodec_dev *main_dev;
> > + void __iomem *reg_base[VDEC_HW_MAX];
> > +
> > + int dec_irq;
> > + struct mtk_vcodec_pm pm;
> > + int hw_idx;
> > +};
> > +
> > +#endif /* _MTK_VCODEC_DEC_HW_H_ */
> > diff --git a/drivers/media/platform/mtk-
> > vcodec/mtk_vcodec_dec_stateful.c b/drivers/media/platform/mtk-
> > vcodec/mtk_vcodec_dec_stateful.c
> > index bef49244e61b..c7f9259ad094 100644
> > --- a/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_stateful.c
> > +++ b/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_stateful.c
> > @@ -625,4 +625,5 @@ const struct mtk_vcodec_dec_pdata
> > mtk_vdec_8173_pdata = {
> > .num_framesizes = NUM_SUPPORTED_FRAMESIZE,
> > .worker = mtk_vdec_worker,
> > .flush_decoder = mtk_vdec_flush_decoder,
> > + .is_subdev_supported = false,
> > };
> > diff --git a/drivers/media/platform/mtk-
> > vcodec/mtk_vcodec_dec_stateless.c b/drivers/media/platform/mtk-
> > vcodec/mtk_vcodec_dec_stateless.c
> > index 26e4d6f4ec04..2d285515b625 100644
> > --- a/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_stateless.c
> > +++ b/drivers/media/platform/mtk-vcodec/mtk_vcodec_dec_stateless.c
> > @@ -357,6 +357,7 @@ const struct mtk_vcodec_dec_pdata
> > mtk_vdec_8183_pdata = {
>
> 8173 might be only one for stateful. But we have multiple platforms
> for 8183. Shouldn't this name reflect this?
>
This platform is used for mt8183, all mt8183 need to used it.
And 8173 is stateful, 8183 is stateless.
> > .uses_stateless_api = true,
> > .worker = mtk_vdec_worker,
> > .flush_decoder = mtk_vdec_flush_decoder,
> > + .is_subdev_supported = false,
> > };
> >
> > const struct mtk_vcodec_dec_pdata mtk_lat_sig_core_pdata = {
> > @@ -373,4 +374,5 @@ const struct mtk_vcodec_dec_pdata
> > mtk_lat_sig_core_pdata = {
>
> Which platforms is this supposed to be used? Some comments on this
> might be helpful.
>
Add in v13.

Thanks,
Yunfei Dong
> > .uses_stateless_api = true,
> > .worker = mtk_vdec_worker,
> > .flush_decoder = mtk_vdec_flush_decoder,
> > + .is_subdev_supported = true,
> > };
> > diff --git a/drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h
> > b/drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h
> > index 0fa9d85114b9..2160f26263ef 100644
> > --- a/drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h
> > +++ b/drivers/media/platform/mtk-vcodec/mtk_vcodec_drv.h
> > @@ -93,6 +93,17 @@ enum mtk_fmt_type {
> > MTK_FMT_FRAME = 2,
> > };
> >
> > +/**
> > + * struct mtk_vdec_hw_id - Hardware index used to separate
> > + * different hardware
> > + */
> > +enum mtk_vdec_hw_id {
> > + MTK_VDEC_CORE,
> > + MTK_VDEC_LAT0,
> > + MTK_VDEC_LAT1,
> > + MTK_VDEC_HW_MAX,
> > +};
> > +
> > /*
> > * struct mtk_video_fmt - Structure used to store information
> > about pixelformats
> > */
> > @@ -332,6 +343,7 @@ enum mtk_chip {
> > *
> > * @chip: chip this decoder is compatible with
> > *
> > + * @is_subdev_supported: whether support parent-node
> > architecture(subdev)
> > * @uses_stateless_api: whether the decoder uses the stateless API
> > with requests
> > */
> >
> > @@ -353,6 +365,7 @@ struct mtk_vcodec_dec_pdata {
> >
> > enum mtk_chip chip;
> >
> > + bool is_subdev_supported;
> > bool uses_stateless_api;
> > };
> >
> > @@ -423,6 +436,9 @@ struct mtk_vcodec_enc_pdata {
> > * @pm: power management control
> > * @dec_capability: used to identify decode capability, ex: 4k
> > * @enc_capability: used to identify encode capability
> > + *
> > + * @subdev_dev: subdev hardware device
> > + * @subdev_bitmap: used to record hardware is ready or not
> > */
> > struct mtk_vcodec_dev {
> > struct v4l2_device v4l2_dev;
> > @@ -460,6 +476,9 @@ struct mtk_vcodec_dev {
> > struct mtk_vcodec_pm pm;
> > unsigned int dec_capability;
> > unsigned int enc_capability;
> > +
> > + void *subdev_dev[MTK_VDEC_HW_MAX];
> > + DECLARE_BITMAP(subdev_bitmap, MTK_VDEC_HW_MAX);
> > };
> >
> > static inline struct mtk_vcodec_ctx *fh_to_ctx(struct v4l2_fh *fh)
> > --
> > 2.25.1
> >
\
 
 \ /
  Last update: 2021-12-13 09:41    [W:0.118 / U:0.036 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site