lkml.org 
[lkml]   [2021]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
From
Subject[PATCH v4 2/2] usb: misc: ehset: Rework test mode entry
Date
The USB2.0 spec chapter 11.24.2.13 says that the USB port which is going
under test needs to be put in suspend state before sending the test
command. Many hubs, don't enforce this precondition and they work fine
without this step. We should follow the specification and put the USB
port in suspend before sending the test command.

Also there are some "special" hubs, which requires to disable the USB
port power instead of putting it in suspend. I found out only three hubs
which requires this step, but if more are found, they can be added to
the list.

Since this changes the default implementation, it raises the posibility
of finding other broken hubs which are not compliant with the spec and
the test command might not work is the port is suspended. If such hubs
are found, a similar workaround like the disable part can be implemented
to skip putting the port in suspend.

Signed-off-by: Razvan Heghedus <heghedus.razvan@gmail.com>
---
Changes in v4:
- make a patch series
Changes in v3:
- use usb_device_match_id to correctly match the hub based on VID:PID
- reword commit message to be more explanatory on what the patch does
Changes in v2:
- style change regarding multi-line comments and a new black line after
local variable definitions
- No more corporate email annotation
drivers/usb/misc/ehset.c | 58 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 58 insertions(+)

diff --git a/drivers/usb/misc/ehset.c b/drivers/usb/misc/ehset.c
index f87890f9cd26..986d6589f053 100644
--- a/drivers/usb/misc/ehset.c
+++ b/drivers/usb/misc/ehset.c
@@ -18,6 +18,52 @@
#define TEST_SINGLE_STEP_GET_DEV_DESC 0x0107
#define TEST_SINGLE_STEP_SET_FEATURE 0x0108

+extern const struct usb_device_id *usb_device_match_id(struct usb_device *udev,
+ const struct usb_device_id *id);
+
+/*
+ * A list of USB hubs which requires to disable the power
+ * to the port before starting the testing procedures.
+ */
+static const struct usb_device_id ehset_hub_list[] = {
+ { USB_DEVICE(0x0424, 0x4502) },
+ { USB_DEVICE(0x0424, 0x4913) },
+ { USB_DEVICE(0x0451, 0x8027) },
+ { }
+};
+
+static int ehset_prepare_port_for_testing(struct usb_device *hub_udev, u16 portnum)
+{
+ int ret = 0;
+
+ /*
+ * The USB2.0 spec chapter 11.24.2.13 says that the USB port which is
+ * going under test needs to be put in suspend before sending the
+ * test command. Most hubs don't enforce this precondition, but there
+ * are some hubs which needs to disable the power to the port before
+ * starting the test.
+ */
+ if (usb_device_match_id(hub_udev, ehset_hub_list)) {
+ ret = usb_control_msg_send(hub_udev, 0, USB_REQ_CLEAR_FEATURE,
+ USB_RT_PORT, USB_PORT_FEAT_ENABLE,
+ portnum, NULL, 0, 1000, GFP_KERNEL);
+ /*
+ * Wait for the port to be disabled. It's an arbitrary value
+ * which worked every time.
+ */
+ msleep(100);
+ } else {
+ /*
+ * For the hubs which are compliant with the spec,
+ * put the port in SUSPEND.
+ */
+ ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
+ USB_RT_PORT, USB_PORT_FEAT_SUSPEND,
+ portnum, NULL, 0, 1000, GFP_KERNEL);
+ }
+ return ret;
+}
+
static int ehset_probe(struct usb_interface *intf,
const struct usb_device_id *id)
{
@@ -30,24 +76,36 @@ static int ehset_probe(struct usb_interface *intf,

switch (test_pid) {
case TEST_SE0_NAK_PID:
+ ret = ehset_prepare_port_for_testing(hub_udev, portnum);
+ if (!ret)
+ break;
ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
USB_RT_PORT, USB_PORT_FEAT_TEST,
(USB_TEST_SE0_NAK << 8) | portnum,
NULL, 0, 1000, GFP_KERNEL);
break;
case TEST_J_PID:
+ ret = ehset_prepare_port_for_testing(hub_udev, portnum);
+ if (!ret)
+ break;
ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
USB_RT_PORT, USB_PORT_FEAT_TEST,
(USB_TEST_J << 8) | portnum, NULL, 0,
1000, GFP_KERNEL);
break;
case TEST_K_PID:
+ ret = ehset_prepare_port_for_testing(hub_udev, portnum);
+ if (!ret)
+ break;
ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
USB_RT_PORT, USB_PORT_FEAT_TEST,
(USB_TEST_K << 8) | portnum, NULL, 0,
1000, GFP_KERNEL);
break;
case TEST_PACKET_PID:
+ ret = ehset_prepare_port_for_testing(hub_udev, portnum);
+ if (!ret)
+ break;
ret = usb_control_msg_send(hub_udev, 0, USB_REQ_SET_FEATURE,
USB_RT_PORT, USB_PORT_FEAT_TEST,
(USB_TEST_PACKET << 8) | portnum,
--
2.34.1
\
 
 \ /
  Last update: 2021-12-13 19:37    [W:1.717 / U:0.020 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site