lkml.org 
[lkml]   [2021]   [Dec]   [13]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [PATCH RESEND v2 0/5] Avoid requesting page from DMA zone when no managed pages
On 12/09/21 at 01:59pm, Christoph Lameter wrote:
> On Thu, 9 Dec 2021, Baoquan He wrote:
>
> > > The slab allocators guarantee that all kmalloc allocations are DMA able
> > > indepent of specifying ZONE_DMA/ZONE_DMA32
> >
> > Here you mean we guarantee dma-kmalloc will be DMA able independent of
> > specifying ZONE_DMA/DMA32, or the whole sla/ub allocator?
>
> All memory obtained via kmalloc --independent of "dma-alloc", ZONE_DMA
> etc-- must be dmaable.

This has a prerequisite as you said at below, only if devices can
address full memory, right?


>
> > With my understanding, isn't the reasonable sequence zone DMA firstly if
> > GFP_DMA, then zone DMA32, finaly zone NORMAL. At least, on x86_64, I
> > believe device driver developer prefer to see this because most of time,
> > zone DMA and zone DMA32 are both used for dma buffer allocation, if
> > IOMMU is not enabled. However, memory got from zone NORMAL when required
> > with GFP_DMA, and it succeeds, does it mean that the developer doesn't
> > take the GFP_DMA flag seriously, just try to get buffer for allocation?
>
> ZONE_NORMAL is also used for DMA allocations. ZONE_DMA and ZONE_DMA32 are
> only used if the physical range of memory supported by a device does not
> include all of normal memory.

If devices can address full memory, ZONE_NORMAL can also be used for DMA
allocations. (This covers the systems where IOMMU is provided).

If device has address limit, e.g dma mask is 24bit or 32bit, ZONE_DMA
and ZONE_DMA32 are needed.

>
> > > The size of ZONE_DMA is traditionally depending on the platform. On some
> > > it is 16MB, on some 1G and on some 4GB. ZONE32 is always 4GB and should
> > > only be used if ZONE_DMA has already been used.
> >
> > As said at above, ia64 and riscv don't have ZONE_DMA at all, they just
> > cover low 4G with ZONE_DMA32 alone.
>
> If you do not have devices that are crap and cannot address the full
> memory then you dont need these special zones.

I am not a DMA expert, with my understanding, on x86_64 and arm64, we
have PCIe devices which dma mask is 32bit, means they can only address
ZONE_DMA32. Supporting to address full memory might be too expensive for
devices, e.g on these two ARCHes, supported memory could be deployed on
Petabyte of address.

>
> Sorry this subject has caused confusion multiple times over the years and
> there are still arches that are not implementing this in a consistent way.

Seems so.

And by the way, when I read slub code, noticed a strange phenomenon, I
haven't found out why. When create cache with kmem_cache_create(), zone
flag SLAB_CACHE_DMA, SLAB_CACHE_DMA32 can be specified. allocflags will
store them, and will take out to use when allocating new slab.
Meanwhile, we can also specify gfpflags, but it can't be GFP_DMA32,
because of GFP_SLAB_BUG_MASK. I traced back to very old git history,
didn't find out why GFP_DMA32 can't be specified during
kmem_cache_alloc().

We can completely rely on the cache->allocflags to mark the zone which
we will request page from, but we can also specify gfpflags in
kmem_cache_alloc() to change zone. GFP_DMA32 is prohibited. Here I can
only see that kmalloc() might be the reason, since kmalloc_large()
doesn't have created cache, so no ->allocflags to use.

Is this expected? What can we do to clarify or improve this, at
leaset on code readability?

I am going to post v3, will discard the 'Further thinking' in cover
letter according to your comment. Please help point out if anthing need
be done or missed.

Thanks a lot.

Baoquan
Thanks

\
 
 \ /
  Last update: 2021-12-13 08:40    [W:0.095 / U:0.696 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site