lkml.org 
[lkml]   [2021]   [Dec]   [11]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
From
Date
SubjectRe: [PATCH v2 1/4] ASoC: dt-bindings: stm32: i2s: add audio-graph-card port
On Tue, Dec 7, 2021 at 7:52 AM Alexandre TORGUE
<alexandre.torgue@foss.st.com> wrote:
>
> Hi Rob
>
> On 12/1/21 11:34 PM, Rob Herring wrote:
> > On Fri, Nov 26, 2021 at 11:25:27AM +0100, Olivier MOYSAN wrote:
> >> Hi Rob,
> >>
> >> On 11/25/21 10:26 PM, Rob Herring wrote:
> >>> On Thu, 25 Nov 2021 15:40:50 +0100, Olivier Moysan wrote:
> >>>> The STM2 I2S DAI can be connected via the audio-graph-card.
> >>>> Add port entry into the bindings.
> >>>>
> >>>> Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
> >>>> ---
> >>>> Documentation/devicetree/bindings/sound/st,stm32-i2s.yaml | 5 +++++
> >>>> 1 file changed, 5 insertions(+)
> >>>>
> >>>
> >>> Running 'make dtbs_check' with the schema in this patch gives the
> >>> following warnings. Consider if they are expected or the schema is
> >>> incorrect. These may not be new warnings.
> >>>
> >>> Note that it is not yet a requirement to have 0 warnings for dtbs_check.
> >>> This will change in the future.
> >>>
> >>> Full log is available here: https://patchwork.ozlabs.org/patch/1559750
> >>>
> >>>
> >>> audio-controller@4000b000: 'port' does not match any of the regexes: '^port@[0-9]', 'pinctrl-[0-9]+'
> >>> arch/arm/boot/dts/stm32mp157a-dk1.dt.yaml
> >>> arch/arm/boot/dts/stm32mp157c-dk2.dt.yaml
> >>>
> >>
> >> This warning is not a new one.
> >>
> >> The i2s2 node in stm32mp15xx-dkx.dtsi would require the following binding:
> >> port:
> >> $ref: audio-graph-port.yaml#
> >> unevaluatedProperties: false
> >>
> >> However the spi binding requires to introduce a unit address:
> >> patternProperties:
> >> '^port@[0-9]':
> >> $ref: audio-graph-port.yaml#
> >> unevaluatedProperties: false
> >>
> >> The warning can be removed by re-ordering the bindings patches in the serie,
> >> as "additionalProperties: true" makes the check more tolerant on extra
> >> properties.
> >
> > That's never right.
> >
> >> The patch "ASoC: dt-bindings: stm32: i2s: add audio-graph-card port" can
> >> even be merely dropped.
> >> So, I suggest to resend the serie without audio-graph-card patch.
> >
> > Only if you aren't using audio-graph-card.
> >
> >>
> >> Does it sound too permissive to you ?
> >
> > I think perhaps you need to combine the schemas into 1. Or you need to
> > restructure your dtsi files such that you only add spi specific
> > properties when spi mode is enabled and only add i2s specific properties
> > when i2s mode is enabled. Or use the /delete-property/ directive.
>
> Initially the aim of this series was to fix a "make W=1" warnings seen
> on spi and i2s nodes (duplicate unit-address). Moving both nodes in a
> common node + using a different compatible depending on SPI or I2S usage
> sounded good) but it is not enough. In this series the common node is
> named as following: "spi2s2: spi@4000b000". It is fine for a spi usage
> but if we want to use this "common node" with I2S compatible and
> specific bindings, the node name remains spi@... and then specific spi
> checks are done. For this with this series applied we got this issue
> reported by spi-controller.yaml:
>
> spi@4000b000: port@0: 'compatible' is a required property
>
> So, if we use two separates nodes we got W=1 warning and if we use a
> common node we got yaml check issue. One possibility would be to use a
> common node with a new node name (for example i2spi@...) but I think it
> is not acceptable.

It is acceptable, see this thread[1].

Rob

[1] https://lore.kernel.org/all/20211203183517.11390-1-semen.protsenko@linaro.org/

\
 
 \ /
  Last update: 2021-12-11 21:06    [W:0.096 / U:0.460 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site