lkml.org 
[lkml]   [2021]   [Nov]   [9]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
Patch in this message
/
Date
From
SubjectRe: [PATCH] pci: Don't call resume callback for nearly bound devices
On Tue, Nov 09, 2021 at 06:18:18PM +0100, Rafael J. Wysocki wrote:
> On Tue, Nov 9, 2021 at 7:59 AM Uwe Kleine-König
> <u.kleine-koenig@pengutronix.de> wrote:
> > On Mon, Nov 08, 2021 at 08:56:19PM -0600, Bjorn Helgaas wrote:
> > > [+cc Greg: new device_is_bound() use]
> >
> > ack, that's what I would have suggested now, too.
> >
> > > On Mon, Nov 08, 2021 at 10:22:26PM +0100, Uwe Kleine-König wrote:
> > > > pci_pm_runtime_resume() exits early when the device to resume isn't
> > > > bound yet:
> > > >
> > > > if (!to_pci_driver(dev->driver))
> > > > return 0;
> > > >
> > > > This however isn't true when the device currently probes and
> > > > local_pci_probe() calls pm_runtime_get_sync() because then the driver
> > > > core already setup dev->driver. As a result the driver's resume callback
> > > > is called before the driver's probe function is called and so more often
> > > > than not required driver data isn't setup yet.
> > > >
> > > > So replace the check for the device being unbound by a check that only
> > > > becomes true after .probe() succeeded.
> > >
> > > I like the fact that this patch is short and simple.
> > >
> > > But there are 30+ users of to_pci_driver(). This patch asserts that
> > > *one* of them, pci_pm_runtime_resume(), is special and needs to test
> > > device_is_bound() instead of using to_pci_driver().
> >
> > Maybe for the other locations using device_is_bound(&pdev->dev) instead
> > of to_pci_driver(pdev) != NULL would be nice, too?
> >
> > I have another doubt: device_is_bound() should (according to its
> > kernel-doc) be called with the device lock held. For the call stack that
> > is (maybe) fixed here, the lock is held (by __device_attach). We
> > probably should check if the lock is also held for the other calls of
> > pci_pm_runtime_resume().
> >
> > Hmm, the device lock is a mutex, the pm functions might be called in
> > atomic context, right?
> >
> > > It's special because the current PM implementation calls it via
> > > pm_runtime_get_sync() before the driver's .probe() method. That
> > > connection is a little bit obscure and fragile. What if the PM
> > > implementation changes?
> >
> > Maybe a saver bet would be to not use pm_runtime_get_sync() in
> > local_pci_probe()?
>
> Yes, in principle it might be replaced with pm_runtime_get_noresume().
>
> In theory, that may be problematic if a device is put into a low-power
> state on remove and then the driver is bound again to it.
>
> > I wonder if the same problem exists on remove, i.e. pci_device_remove()
> > calls pm_runtime_put_sync() after the driver's .remove() callback was
> > called.
>
> If it is called after ->remove() and before clearing the device's
> driver pointer, then yes.

Yes, that is the case:

pci_device_remove
if (drv->remove) {
pm_runtime_get_sync
drv->remove() # <-- driver ->remove() method
pm_runtime_put_noidle
}
...
pm_runtime_put_sync # <-- after ->remove()

So pm_runtime_put_sync() is called after drv->remove(), and it may
call drv->pm->runtime_idle(). I think the driver may not expect this.

> If this is turned into pm_runtime_put_noidle(), all should work.

pci_device_remove() already calls pm_runtime_put_noidle() immediately
after calling the driver ->remove() method.

Are you saying we should do this, which means pci_device_remove()
would call pm_runtime_put_noidle() twice?

diff --git a/drivers/pci/pci-driver.c b/drivers/pci/pci-driver.c
index 1d98c974381c..79c1a920fdc8 100644
--- a/drivers/pci/pci-driver.c
+++ b/drivers/pci/pci-driver.c
@@ -318,7 +318,7 @@ static long local_pci_probe(void *_ddi)
* count, in its probe routine and pm_runtime_get_noresume() in
* its remove routine.
*/
- pm_runtime_get_sync(dev);
+ pm_runtime_get_noresume(dev);
rc = pci_drv->probe(pci_dev, ddi->id);
if (!rc)
return rc;
@@ -465,7 +465,7 @@ static void pci_device_remove(struct device *dev)
pci_iov_remove(pci_dev);

/* Undo the runtime PM settings in local_pci_probe() */
- pm_runtime_put_sync(dev);
+ pm_runtime_put_noidle(dev);

/*
* If the device is still on, set the power state as "unknown",
\
 
 \ /
  Last update: 2021-11-09 19:13    [W:0.133 / U:0.272 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site