lkml.org 
[lkml]   [2021]   [Nov]   [8]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
/
Date
From
SubjectRe: [RFC PATCH v2 1/5] leds: trigger: add API for HW offloading of triggers
On Mon, Nov 08, 2021 at 09:11:10PM +0100, Marek Behún wrote:
> On Mon, 8 Nov 2021 20:53:36 +0100
> Andrew Lunn <andrew@lunn.ch> wrote:
>
> > > I guess I will have to work on this again ASAP or we will end up with
> > > solution that I don't like.
> > >
> > > Nonetheless, what is your opinion about offloading netdev trigger vs
> > > introducing another trigger?
> >
> > It is a solution that fits the general pattern, do it in software, and
> > offload it if possible.
> >
> > However, i'm not sure the software solution actually works very well.
> > At least for switches. The two DSA drivers which implement
> > get_stats64() simply copy the cached statistics. The XRS700X updates
> > its cached values every 3000ms. The ar9331 is the same. Those are the
> > only two switch drivers which implement get_stats64 and none implement
> > get_stats. There was also was an issue that get_stats64() cannot
> > perform blocking calls. I don't remember if that was fixed, but if
> > not, get_stats64() is going to be pretty useless on switches.
> >
> > We also need to handle drivers which don't actually implement
> > dev_get_stats(). That probably means only supporting offloads, all
> > modes which cannot be offloaded need to be rejected. This is pretty
> > much the same case of software control of the LEDs is not possible.
> > Unfortunately, dev_get_stats() does not return -EOPNOTSUPP, you need
> > to look at dev->netdev_ops->ndo_get_stats64 and
> > dev->netdev_ops->ndo_get_stats.
> >
> > Are you working on Marvell switches? Have you implemented
> > get_stats64() for mv88e6xxx? How often do you poll the hardware for
> > the stats?
> >
> > Given this, i think we need to bias the API so that it very likely
> > ends up offloading, if offloading is available.
>
> I am working with Marvell PHYs and Marvell switches. I am aware of the
> problem that SW netdev does not work for switches because we don't have
> uptodate data.
>
> It seems to me that yes, if the user wants to blink the LEDs on
> activity on switch port, the netdev trigger should only work in offload
> mode and only on LEDs that are connected to switch pins, unless we
> implement a mechanism to get statistics at lest 10 times a second
> (which could maybe be done on marvell switches by reading the registers
> via ethernet frames instead of MDIO).
>
> Marvell switches don't seem to support rx only / tx only activity
> blinking, only rx/tx. I think this could be solved by making rx/tx
> sysfs files for netdev trigger behave so that writing to one would also
> write to another.
>
> But since currently netdev trigger does not work for these switches, I
> think making it so that it works at least to some fashion (in HW
> supported modes) would still be better that current situation.
>
> I will try to look into this, maybe work together with Ansuel.
>
> Marek

I'm polishing some api with Andrew comments and will try to extend
netdev trigger while still proposing the additional trigger. Better
discuss in v3.
I think the main target here is first have a good generic solution for
offload and then actually thinking about working on the triggers/offload
part.

--
Ansuel

\
 
 \ /
  Last update: 2021-11-08 21:16    [W:0.194 / U:0.016 seconds]
©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site