lkml.org 
[lkml]   [2021]   [Nov]   [30]   [last100]   RSS Feed
Views: [wrap][no wrap]   [headers]  [forward] 
 
Messages in this thread
    Patch in this message
    /
    From
    Subject[PATCH v2] gpio: xlp: Remove Netlogic XLP variants
    Date
    Netlogic XLP was removed in commit 95b8a5e0111a ("MIPS: Remove NETLOGIC
    support"). With those gone, the single platform left to support is
    Cavium ThunderX2. Remove all the Netlogic variants and DT support.

    For simplicity, the existing kconfig name is retained.

    Cc: Linus Walleij <linus.walleij@linaro.org>
    Cc: Bartosz Golaszewski <brgl@bgdev.pl>
    Cc: linux-gpio@vger.kernel.org
    Signed-off-by: Rob Herring <robh@kernel.org>
    ---
    v2:
    - Fix !OF and ACPI build errors

    drivers/gpio/Kconfig | 10 ++-
    drivers/gpio/gpio-xlp.c | 147 +++-------------------------------------
    2 files changed, 15 insertions(+), 142 deletions(-)

    diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
    index 072ed610f9c6..e05f226b3d5d 100644
    --- a/drivers/gpio/Kconfig
    +++ b/drivers/gpio/Kconfig
    @@ -730,14 +730,12 @@ config GPIO_XILINX
    Say yes here to support the Xilinx FPGA GPIO device.

    config GPIO_XLP
    - tristate "Netlogic XLP GPIO support"
    - depends on OF_GPIO && (CPU_XLP || ARCH_THUNDER2 || COMPILE_TEST)
    + tristate "Cavium ThunderX2 GPIO support"
    + depends on ARCH_THUNDER2 || COMPILE_TEST
    select GPIOLIB_IRQCHIP
    help
    - This driver provides support for GPIO interface on Netlogic XLP MIPS64
    - SoCs. Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX,
    - XLP9XX and XLP5XX. The same GPIO controller block is also present in
    - Cavium's ThunderX2 CN99XX SoCs.
    + This driver provides support for GPIO interface on Cavium's ThunderX2
    + CN99XX SoCs (Originally from Netlogic XLP).

    If unsure, say N.

    diff --git a/drivers/gpio/gpio-xlp.c b/drivers/gpio/gpio-xlp.c
    index 0d94d3aef752..0199f545335f 100644
    --- a/drivers/gpio/gpio-xlp.c
    +++ b/drivers/gpio/gpio-xlp.c
    @@ -6,7 +6,6 @@

    #include <linux/gpio/driver.h>
    #include <linux/platform_device.h>
    -#include <linux/of_device.h>
    #include <linux/module.h>
    #include <linux/irq.h>
    #include <linux/interrupt.h>
    @@ -26,16 +25,6 @@
    *
    * where addr is base address of the that feature register and gpio is the pin.
    */
    -#define GPIO_OUTPUT_EN 0x00
    -#define GPIO_PADDRV 0x08
    -#define GPIO_INT_EN00 0x18
    -#define GPIO_INT_EN10 0x20
    -#define GPIO_INT_EN20 0x28
    -#define GPIO_INT_EN30 0x30
    -#define GPIO_INT_POL 0x38
    -#define GPIO_INT_TYPE 0x40
    -#define GPIO_INT_STAT 0x48
    -
    #define GPIO_9XX_BYTESWAP 0X00
    #define GPIO_9XX_CTRL 0X04
    #define GPIO_9XX_OUTPUT_EN 0x14
    @@ -52,14 +41,6 @@
    #define GPIO_9XX_INT_TYPE 0x114
    #define GPIO_9XX_INT_STAT 0x124

    -#define GPIO_3XX_INT_EN00 0x18
    -#define GPIO_3XX_INT_EN10 0x20
    -#define GPIO_3XX_INT_EN20 0x28
    -#define GPIO_3XX_INT_EN30 0x30
    -#define GPIO_3XX_INT_POL 0x78
    -#define GPIO_3XX_INT_TYPE 0x80
    -#define GPIO_3XX_INT_STAT 0x88
    -
    /* Interrupt type register mask */
    #define XLP_GPIO_IRQ_TYPE_LVL 0x0
    #define XLP_GPIO_IRQ_TYPE_EDGE 0x1
    @@ -72,16 +53,6 @@
    #define XLP_GPIO_IRQ_BASE 768
    #define XLP_MAX_NR_GPIO 96

    -/* XLP variants supported by this driver */
    -enum {
    - XLP_GPIO_VARIANT_XLP832 = 1,
    - XLP_GPIO_VARIANT_XLP316,
    - XLP_GPIO_VARIANT_XLP208,
    - XLP_GPIO_VARIANT_XLP980,
    - XLP_GPIO_VARIANT_XLP532,
    - GPIO_VARIANT_VULCAN
    -};
    -
    struct xlp_gpio_priv {
    struct gpio_chip chip;
    DECLARE_BITMAP(gpio_enabled_mask, XLP_MAX_NR_GPIO);
    @@ -257,44 +228,13 @@ static void xlp_gpio_set(struct gpio_chip *gc, unsigned gpio, int state)
    xlp_gpio_set_reg(priv->gpio_paddrv, gpio, state);
    }

    -static const struct of_device_id xlp_gpio_of_ids[] = {
    - {
    - .compatible = "netlogic,xlp832-gpio",
    - .data = (void *)XLP_GPIO_VARIANT_XLP832,
    - },
    - {
    - .compatible = "netlogic,xlp316-gpio",
    - .data = (void *)XLP_GPIO_VARIANT_XLP316,
    - },
    - {
    - .compatible = "netlogic,xlp208-gpio",
    - .data = (void *)XLP_GPIO_VARIANT_XLP208,
    - },
    - {
    - .compatible = "netlogic,xlp980-gpio",
    - .data = (void *)XLP_GPIO_VARIANT_XLP980,
    - },
    - {
    - .compatible = "netlogic,xlp532-gpio",
    - .data = (void *)XLP_GPIO_VARIANT_XLP532,
    - },
    - {
    - .compatible = "brcm,vulcan-gpio",
    - .data = (void *)GPIO_VARIANT_VULCAN,
    - },
    - { /* sentinel */ },
    -};
    -MODULE_DEVICE_TABLE(of, xlp_gpio_of_ids);
    -
    static int xlp_gpio_probe(struct platform_device *pdev)
    {
    struct gpio_chip *gc;
    struct gpio_irq_chip *girq;
    struct xlp_gpio_priv *priv;
    void __iomem *gpio_base;
    - int irq_base, irq, err;
    - int ngpio;
    - u32 soc_type;
    + int irq, err;

    priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
    if (!priv)
    @@ -308,62 +248,12 @@ static int xlp_gpio_probe(struct platform_device *pdev)
    if (irq < 0)
    return irq;

    - if (pdev->dev.of_node) {
    - soc_type = (uintptr_t)of_device_get_match_data(&pdev->dev);
    - } else {
    - const struct acpi_device_id *acpi_id;
    -
    - acpi_id = acpi_match_device(pdev->dev.driver->acpi_match_table,
    - &pdev->dev);
    - if (!acpi_id || !acpi_id->driver_data) {
    - dev_err(&pdev->dev, "Unable to match ACPI ID\n");
    - return -ENODEV;
    - }
    - soc_type = (uintptr_t) acpi_id->driver_data;
    - }
    -
    - switch (soc_type) {
    - case XLP_GPIO_VARIANT_XLP832:
    - priv->gpio_out_en = gpio_base + GPIO_OUTPUT_EN;
    - priv->gpio_paddrv = gpio_base + GPIO_PADDRV;
    - priv->gpio_intr_stat = gpio_base + GPIO_INT_STAT;
    - priv->gpio_intr_type = gpio_base + GPIO_INT_TYPE;
    - priv->gpio_intr_pol = gpio_base + GPIO_INT_POL;
    - priv->gpio_intr_en = gpio_base + GPIO_INT_EN00;
    - ngpio = 41;
    - break;
    - case XLP_GPIO_VARIANT_XLP208:
    - case XLP_GPIO_VARIANT_XLP316:
    - priv->gpio_out_en = gpio_base + GPIO_OUTPUT_EN;
    - priv->gpio_paddrv = gpio_base + GPIO_PADDRV;
    - priv->gpio_intr_stat = gpio_base + GPIO_3XX_INT_STAT;
    - priv->gpio_intr_type = gpio_base + GPIO_3XX_INT_TYPE;
    - priv->gpio_intr_pol = gpio_base + GPIO_3XX_INT_POL;
    - priv->gpio_intr_en = gpio_base + GPIO_3XX_INT_EN00;
    -
    - ngpio = (soc_type == XLP_GPIO_VARIANT_XLP208) ? 42 : 57;
    - break;
    - case XLP_GPIO_VARIANT_XLP980:
    - case XLP_GPIO_VARIANT_XLP532:
    - case GPIO_VARIANT_VULCAN:
    - priv->gpio_out_en = gpio_base + GPIO_9XX_OUTPUT_EN;
    - priv->gpio_paddrv = gpio_base + GPIO_9XX_PADDRV;
    - priv->gpio_intr_stat = gpio_base + GPIO_9XX_INT_STAT;
    - priv->gpio_intr_type = gpio_base + GPIO_9XX_INT_TYPE;
    - priv->gpio_intr_pol = gpio_base + GPIO_9XX_INT_POL;
    - priv->gpio_intr_en = gpio_base + GPIO_9XX_INT_EN00;
    -
    - if (soc_type == XLP_GPIO_VARIANT_XLP980)
    - ngpio = 66;
    - else if (soc_type == XLP_GPIO_VARIANT_XLP532)
    - ngpio = 67;
    - else
    - ngpio = 70;
    - break;
    - default:
    - dev_err(&pdev->dev, "Unknown Processor type!\n");
    - return -ENODEV;
    - }
    + priv->gpio_out_en = gpio_base + GPIO_9XX_OUTPUT_EN;
    + priv->gpio_paddrv = gpio_base + GPIO_9XX_PADDRV;
    + priv->gpio_intr_stat = gpio_base + GPIO_9XX_INT_STAT;
    + priv->gpio_intr_type = gpio_base + GPIO_9XX_INT_TYPE;
    + priv->gpio_intr_pol = gpio_base + GPIO_9XX_INT_POL;
    + priv->gpio_intr_en = gpio_base + GPIO_9XX_INT_EN00;

    bitmap_zero(priv->gpio_enabled_mask, XLP_MAX_NR_GPIO);

    @@ -373,8 +263,7 @@ static int xlp_gpio_probe(struct platform_device *pdev)
    gc->label = dev_name(&pdev->dev);
    gc->base = 0;
    gc->parent = &pdev->dev;
    - gc->ngpio = ngpio;
    - gc->of_node = pdev->dev.of_node;
    + gc->ngpio = 70;
    gc->direction_output = xlp_gpio_dir_output;
    gc->direction_input = xlp_gpio_dir_input;
    gc->set = xlp_gpio_set;
    @@ -382,19 +271,6 @@ static int xlp_gpio_probe(struct platform_device *pdev)

    spin_lock_init(&priv->lock);

    - /* XLP(MIPS) has fixed range for GPIO IRQs, Vulcan(ARM64) does not */
    - if (soc_type != GPIO_VARIANT_VULCAN) {
    - irq_base = devm_irq_alloc_descs(&pdev->dev, -1,
    - XLP_GPIO_IRQ_BASE,
    - gc->ngpio, 0);
    - if (irq_base < 0) {
    - dev_err(&pdev->dev, "Failed to allocate IRQ numbers\n");
    - return irq_base;
    - }
    - } else {
    - irq_base = 0;
    - }
    -
    girq = &gc->irq;
    girq->chip = &xlp_gpio_irq_chip;
    girq->parent_handler = xlp_gpio_generic_handler;
    @@ -405,7 +281,7 @@ static int xlp_gpio_probe(struct platform_device *pdev)
    if (!girq->parents)
    return -ENOMEM;
    girq->parents[0] = irq;
    - girq->first = irq_base;
    + girq->first = 0;
    girq->default_type = IRQ_TYPE_NONE;
    girq->handler = handle_level_irq;

    @@ -420,8 +296,8 @@ static int xlp_gpio_probe(struct platform_device *pdev)

    #ifdef CONFIG_ACPI
    static const struct acpi_device_id xlp_gpio_acpi_match[] = {
    - { "BRCM9006", GPIO_VARIANT_VULCAN },
    - { "CAV9006", GPIO_VARIANT_VULCAN },
    + { "BRCM9006" },
    + { "CAV9006" },
    {},
    };
    MODULE_DEVICE_TABLE(acpi, xlp_gpio_acpi_match);
    @@ -430,7 +306,6 @@ MODULE_DEVICE_TABLE(acpi, xlp_gpio_acpi_match);
    static struct platform_driver xlp_gpio_driver = {
    .driver = {
    .name = "xlp-gpio",
    - .of_match_table = xlp_gpio_of_ids,
    .acpi_match_table = ACPI_PTR(xlp_gpio_acpi_match),
    },
    .probe = xlp_gpio_probe,
    --
    2.32.0
    \
     
     \ /
      Last update: 2021-11-30 20:59    [W:2.501 / U:0.008 seconds]
    ©2003-2020 Jasper Spaans|hosted at Digital Ocean and TransIP|Read the blog|Advertise on this site